[PATCH v8 2/5] include: linux: phy: Add phy attribute "type" and associated helpers

[Krishna Kurapati]

On 10/5/2026 2:14 PM, Vinod Koul wrote:
> On 13-09-26, 20:10, Krishna Kurapati wrote:
>> In cases like USB High-speed phys which can be either USB2 or EUSB2, it is
>> required to know the type of phy (rather than the operating mode) because
>> DP and DM interrupt lines need to be configured differently for each of
>> them.
> 
> Does the controller care? In preceding patch you defined the EUSB2 in dt
> type, so this describes the hardware. So phy knows it is usb or eusb...
>>

Controller is agnostic of whether the phy is usb2 or eusb2. Phy does now 
its type, but it needs to communicate the same to controller.

>> Add support to cache the PHY_TYPE and add the following helpers:
>>
>> - phy_set_type() for the phy drivers (like m31_eusb2 or snps-eusb2) to
>> declare what type of PHY they are (in this case PHY_TYPE_EUSB2).
>>
>> - phy_get_type() for the consumers (like USB controllers) to query the
>> type of phy connected to them.
> 
> I am not convinced that this is the way to go... Driver already knows
> the type and should use it...
> we alreayd have mode, i am inclined to not say yes to adding type here
> 

"Mode" attribute describes the current operating scenario of the phy 
(device mode, host mode, high speed, super speed etc.,). But it doesn't 
describe the type of hardware and hence a new attribute.

Regards,
Krishna,

>>
>> Reviewed-by: Thinh Nguyen <Thinh.Nguyen at synopsys.com>
>> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam at oss.qualcomm.com>
>> Signed-off-by: Krishna Kurapati <krishna.kurapati at oss.qualcomm.com>
>> ---
>>   include/linux/phy/phy.h | 27 +++++++++++++++++++++++++++
>>   1 file changed, 27 insertions(+)
>>
>> diff --git a/include/linux/phy/phy.h b/include/linux/phy/phy.h
>> index ea47975e288a..038c2b58bbe1 100644
>> --- a/include/linux/phy/phy.h
>> +++ b/include/linux/phy/phy.h
>> @@ -21,6 +21,8 @@
>>   #include <linux/phy/phy-lvds.h>
>>   #include <linux/phy/phy-mipi-dphy.h>
>>   
>> +#include <dt-bindings/phy/phy.h>
>> +
>>   struct phy;
>>   
>>   enum phy_mode {
>> @@ -152,11 +154,13 @@ struct phy_ops {
>>    * @bus_width: Data path width implemented by PHY
>>    * @max_link_rate: Maximum link rate supported by PHY (units to be decided by producer and consumer)
>>    * @mode: PHY mode
>> + * @type: PHY type
>>    */
>>   struct phy_attrs {
>>   	u32			bus_width;
>>   	u32			max_link_rate;
>>   	enum phy_mode		mode;
>> +	int			type;
>>   };
>>   
>>   /**
>> @@ -262,6 +266,20 @@ static inline enum phy_mode phy_get_mode(struct phy *phy)
>>   {
>>   	return phy->attrs.mode;
>>   }
>> +
>> +static inline int phy_get_type(struct phy *phy)
>> +{
>> +	if (phy)
>> +		return phy->attrs.type;
>> +
>> +	return PHY_NONE;
>> +}
>> +
>> +static inline void phy_set_type(struct phy *phy, int type)
>> +{
>> +	phy->attrs.type = type;
>> +}
>> +
>>   int phy_reset(struct phy *phy);
>>   int phy_calibrate(struct phy *phy);
>>   int phy_notify_connect(struct phy *phy, int port);
>> @@ -393,6 +411,15 @@ static inline enum phy_mode phy_get_mode(struct phy *phy)
>>   	return PHY_MODE_INVALID;
>>   }
>>   
>> +static inline int phy_get_type(struct phy *phy)
>> +{
>> +	return PHY_NONE;
>> +}
>> +
>> +static inline void phy_set_type(struct phy *phy, int type)
>> +{
>> +}
>> +
>>   static inline int phy_reset(struct phy *phy)
>>   {
>>   	if (!phy)
>>
>> -- 
>> 2.34.1
>