[PATCH 14/17] phy: qcom: edp: Add Nord PLL configuration callback

[Nabige Aala]

On 9/14/2026 5:42 AM, Dmitry Baryshkov wrote:
> On Fri, Sep 11, 2026 at 09:06:45PM +0530, Nabige Aala wrote:
>> From: Ritesh Kumar <ritesh.kumar at oss.qualcomm.com>
>>
>> Nord uses a 38.4 MHz CXO reference with a different QSERDES v8 COM
>> register layout and PLL coefficients.  Add
>> qcom_edp_com_configure_pll_nord() which programs all QSERDES COM PLL
>> registers with link-rate-dependent values for RBR, HBR, HBR2 and
>> HBR3, per HPG Table 2-1-d.
>>
>> Signed-off-by: Ritesh Kumar <ritesh.kumar at oss.qualcomm.com>
>> Signed-off-by: Nabige Aala <nabige.aala at oss.qualcomm.com>
>> ---
>>   drivers/phy/qualcomm/phy-qcom-edp.c | 112 ++++++++++++++++++++++++++++++++++++
>>   1 file changed, 112 insertions(+)
>>
>> diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c
>> index a0f4b12e561e..4d1b2c81d956 100644
>> --- a/drivers/phy/qualcomm/phy-qcom-edp.c
>> +++ b/drivers/phy/qualcomm/phy-qcom-edp.c
>> @@ -1688,6 +1688,118 @@ static int qcom_edp_com_configure_ssc_nord(const struct qcom_edp *edp)
>>   }
>>   
>>   
>> +/*
>> + * Nord PLL configuration per HPG Table 2-1-d, CXO = 38.4 MHz.
>> + * Supported link rates: 1.62 Gbps (RBR), 2.7 Gbps (HBR),
>> + * 5.4 Gbps (HBR2), 8.1 Gbps (HBR3).
>> + */
>> +static int qcom_edp_com_configure_pll_nord(const struct qcom_edp *edp)
>> +{
>> +	const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
>> +	u32 div_frac_start1_mode0;
>> +	u32 div_frac_start2_mode0;
>> +	u32 div_frac_start3_mode0;
>> +	u32 dec_start_mode0;
>> +	u32 lock_cmp1_mode0;
>> +	u32 lock_cmp2_mode0;
>> +	u32 lock_cmp_en;
>> +	u32 hsclk_sel;
>> +	u32 code1_mode0;
>> +	u32 code2_mode0;
>> +	u32 core_clk_div_mode0 = 0x14;
>> +
>> +	switch (dp_opts->link_rate) {
>> +	case 1620:
>> +		hsclk_sel		= 0x0c;
>> +		dec_start_mode0		= 0x54;
>> +		div_frac_start1_mode0	= 0x00;
>> +		div_frac_start2_mode0	= 0x00;
>> +		div_frac_start3_mode0	= 0x06;
>> +		lock_cmp1_mode0		= 0x37;
>> +		lock_cmp2_mode0		= 0x04;
>> +		lock_cmp_en		= 0x04;
>> +		code1_mode0		= 0x8d;
>> +		code2_mode0		= 0x27;
> No extra alignment, please.
Ack
>
>> +		break;
>> +
>> +	case 2700:
>> +		hsclk_sel		= 0x04;
>> +		dec_start_mode0		= 0x46;
>> +		div_frac_start1_mode0	= 0x00;
>> +		div_frac_start2_mode0	= 0x00;
>> +		div_frac_start3_mode0	= 0x05;
>> +		lock_cmp1_mode0		= 0x07;
>> +		lock_cmp2_mode0		= 0x07;
>> +		lock_cmp_en		= 0x08;
>> +		code1_mode0		= 0xf6;
>> +		code2_mode0		= 0x20;
>> +		break;
>> +
>> +	case 5400:
>> +		hsclk_sel		= 0x01;
>> +		dec_start_mode0		= 0x46;
>> +		div_frac_start1_mode0	= 0x00;
>> +		div_frac_start2_mode0	= 0x00;
>> +		div_frac_start3_mode0	= 0x05;
>> +		lock_cmp1_mode0		= 0x0f;
>> +		lock_cmp2_mode0		= 0x0e;
>> +		lock_cmp_en		= 0x08;
>> +		code1_mode0		= 0xf6;
>> +		code2_mode0		= 0x20;
>> +		break;
>> +
>> +	case 8100:
>> +		hsclk_sel		= 0x03;
>> +		dec_start_mode0		= 0x4f;
>> +		div_frac_start1_mode0	= 0x00;
>> +		div_frac_start2_mode0	= 0xa0;
>> +		div_frac_start3_mode0	= 0x01;
>> +		lock_cmp1_mode0		= 0x17;
>> +		lock_cmp2_mode0		= 0x15;
>> +		lock_cmp_en		= 0x08;
>> +		code1_mode0		= 0x14;
>> +		code2_mode0		= 0x25;
>> +		core_clk_div_mode0	= 0x0a;
>> +		break;
>> +
>> +	default:
>> +		return -EINVAL;
>> +	}
>> +
>> +	writel(0x01, edp->pll + DP_QSERDES_V8_COM_SVS_MODE_CLK_SEL_NORD);
>> +	writel(0x0b, edp->pll + DP_QSERDES_V8_COM_SYSCLK_EN_SEL);
>> +	writel(0x02, edp->pll + DP_QSERDES_V8_COM_SYS_CLK_CTRL);
>> +	writel(0x0c, edp->pll + DP_QSERDES_V8_COM_CLK_ENABLE1);
>> +	writel(0x06, edp->pll + DP_QSERDES_V8_COM_SYSCLK_BUF_ENABLE);
>> +	writel(0x30, edp->pll + DP_QSERDES_V8_COM_CLK_SELECT);
>> +	writel(hsclk_sel, edp->pll + DP_QSERDES_V8_COM_HSCLK_SEL_1);
>> +	writel(0x07, edp->pll + DP_QSERDES_V8_COM_PLL_IVCO);
>> +	writel(lock_cmp_en, edp->pll + DP_QSERDES_V8_COM_LOCK_CMP_EN);
>> +	writel(0x36, edp->pll + DP_QSERDES_V8_COM_PLL_CCTRL_MODE0);
>> +	writel(0x16, edp->pll + DP_QSERDES_V8_COM_PLL_RCTRL_MODE0);
>> +	writel(0x06, edp->pll + DP_QSERDES_V8_COM_CP_CTRL_MODE0);
>> +	writel(dec_start_mode0, edp->pll + DP_QSERDES_V8_COM_DEC_START_MODE0);
>> +	writel(div_frac_start1_mode0, edp->pll + DP_QSERDES_V8_COM_DIV_FRAC_START1_MODE0);
> Always 0x00
Ack, This value is always 0x00 will update this in next revision.
>
>> +	writel(div_frac_start2_mode0, edp->pll + DP_QSERDES_V8_COM_DIV_FRAC_START2_MODE0);
>> +	writel(div_frac_start3_mode0, edp->pll + DP_QSERDES_V8_COM_DIV_FRAC_START3_MODE0);
>> +	writel(0x12, edp->pll + DP_QSERDES_V8_COM_CMN_CONFIG_1);
>> +	writel(0x3f, edp->pll + DP_QSERDES_V8_COM_INTEGLOOP_GAIN0_MODE0);
>> +	writel(0x00, edp->pll + DP_QSERDES_V8_COM_INTEGLOOP_GAIN1_MODE0);
>> +	writel(0x00, edp->pll + DP_QSERDES_V8_COM_VCO_TUNE_MAP);
>> +	writel(lock_cmp1_mode0, edp->pll + DP_QSERDES_V8_COM_LOCK_CMP1_MODE0);
>> +	writel(lock_cmp2_mode0, edp->pll + DP_QSERDES_V8_COM_LOCK_CMP2_MODE0);
>> +	writel(0x0a, edp->pll + DP_QSERDES_V8_COM_BG_TIMER);
>> +	writel(core_clk_div_mode0, edp->pll + DP_QSERDES_V8_COM_CORECLK_DIV_MODE0);
>> +	writel(0x00, edp->pll + DP_QSERDES_V8_COM_VCO_TUNE_CTRL);
>> +	writel(0x1d, edp->pll + DP_QSERDES_V8_COM_BIAS_EN_CLKBUFLR_EN);
> Not 0x1f?
Ack, This should be 0x1f. I will update in next revision.
>
>> +	writel(0x0f, edp->pll + DP_QSERDES_V8_COM_CORE_CLK_EN);
> No DP_QSERDES_V8_COM_VCO_TUNE1_MODE0 /
> DP_QSERDES_V8_COM_VCO_TUNE2_MODE0?

As per HPG, We dont need to programmed these for Nord.

Thanks,

Nabige

>> +	writel(code1_mode0, edp->pll + DP_QSERDES_V8_COM_BIN_VCOCAL_CMP_CODE1_MODE0);
>> +	writel(code2_mode0, edp->pll + DP_QSERDES_V8_COM_BIN_VCOCAL_CMP_CODE2_MODE0);
>> +
>> +	return 0;
>> +}
>> +
>> +
>>   static const struct of_device_id qcom_edp_phy_match_table[] = {
>>   	{ .compatible = "qcom,glymur-dp-phy", .data = &glymur_phy_cfg, },
>>   	{ .compatible = "qcom,sa8775p-edp-phy", .data = &sa8775p_dp_phy_cfg, },
>>
>> -- 
>> 2.34.1
>>