[PATCH v4 linux-phy 2/3] phy: ti: alphabetically sort Kconfig and Makefile
Ioana Ciornei
ioana.ciornei at nxp.com
Mon May 18 07:20:25 PDT 2026
Sort alphabetically the entries in the Kconfig and Makefile files.
Signed-off-by: Ioana Ciornei <ioana.ciornei at nxp.com>
---
Changes in v4:
- patch is new
---
drivers/phy/ti/Kconfig | 92 ++++++++++++++++++++---------------------
drivers/phy/ti/Makefile | 12 +++---
2 files changed, 52 insertions(+), 52 deletions(-)
diff --git a/drivers/phy/ti/Kconfig b/drivers/phy/ti/Kconfig
index b40f28019131..dbe65500f20c 100644
--- a/drivers/phy/ti/Kconfig
+++ b/drivers/phy/ti/Kconfig
@@ -2,24 +2,29 @@
#
# Phy drivers for TI platforms
#
-config PHY_DA8XX_USB
- tristate "TI DA8xx USB PHY Driver"
- depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST
- select GENERIC_PHY
- select MFD_SYSCON
+config OMAP_CONTROL_PHY
+ tristate "OMAP CONTROL PHY Driver"
+ depends on ARCH_OMAP2PLUS || COMPILE_TEST
help
- Enable this to support the USB PHY on DA8xx SoCs.
-
- This driver controls both the USB 1.1 PHY and the USB 2.0 PHY.
+ Enable this to add support for the PHY part present in the control
+ module. This driver has API to power on the USB2 PHY and to write to
+ the mailbox. The mailbox is present only in omap4 and the register to
+ power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
+ additional register to power on USB3 PHY/SATA PHY/PCIE PHY
+ (PIPE3 PHY).
-config PHY_DM816X_USB
- tristate "TI dm816x USB PHY driver"
- depends on ARCH_OMAP2PLUS || COMPILE_TEST
+config OMAP_USB2
+ tristate "OMAP USB2 PHY Driver"
+ depends on ARCH_OMAP2PLUS || ARCH_K3 || COMPILE_TEST
depends on USB_SUPPORT
select GENERIC_PHY
select USB_PHY
+ select OMAP_CONTROL_PHY if ARCH_OMAP2PLUS || COMPILE_TEST
help
- Enable this for dm816x USB to work.
+ Enable this to support the transceiver that is part of SOC. This
+ driver takes care of all the PHY functionality apart from comparator.
+ The USB OTG controller communicates with the comparator using this
+ driver.
config PHY_AM654_SERDES
tristate "TI AM654 SERDES support"
@@ -33,6 +38,25 @@ config PHY_AM654_SERDES
This option enables support for TI AM654 SerDes PHY used for
PCIe.
+config PHY_DA8XX_USB
+ tristate "TI DA8xx USB PHY Driver"
+ depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ Enable this to support the USB PHY on DA8xx SoCs.
+
+ This driver controls both the USB 1.1 PHY and the USB 2.0 PHY.
+
+config PHY_DM816X_USB
+ tristate "TI dm816x USB PHY driver"
+ depends on ARCH_OMAP2PLUS || COMPILE_TEST
+ depends on USB_SUPPORT
+ select GENERIC_PHY
+ select USB_PHY
+ help
+ Enable this for dm816x USB to work.
+
config PHY_J721E_WIZ
tristate "TI J721E WIZ (SERDES Wrapper) support"
depends on OF && (ARCH_K3 || COMPILE_TEST)
@@ -49,29 +73,20 @@ config PHY_J721E_WIZ
three clock selects (pll0, pll1, dig) and resets for each of the
lanes.
-config OMAP_CONTROL_PHY
- tristate "OMAP CONTROL PHY Driver"
- depends on ARCH_OMAP2PLUS || COMPILE_TEST
+config PHY_TI_GMII_SEL
+ tristate
+ select GENERIC_PHY
+ select REGMAP
help
- Enable this to add support for the PHY part present in the control
- module. This driver has API to power on the USB2 PHY and to write to
- the mailbox. The mailbox is present only in omap4 and the register to
- power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
- additional register to power on USB3 PHY/SATA PHY/PCIE PHY
- (PIPE3 PHY).
+ This driver supports configuring of the TI CPSW Port mode depending on
+ the Ethernet PHY connected to the CPSW Port.
-config OMAP_USB2
- tristate "OMAP USB2 PHY Driver"
- depends on ARCH_OMAP2PLUS || ARCH_K3 || COMPILE_TEST
- depends on USB_SUPPORT
+config PHY_TUSB1210
+ tristate "TI TUSB1210 ULPI PHY module"
+ depends on USB_ULPI_BUS
select GENERIC_PHY
- select USB_PHY
- select OMAP_CONTROL_PHY if ARCH_OMAP2PLUS || COMPILE_TEST
help
- Enable this to support the transceiver that is part of SOC. This
- driver takes care of all the PHY functionality apart from comparator.
- The USB OTG controller communicates with the comparator using this
- driver.
+ Support for TI TUSB1210 USB ULPI PHY.
config TI_PIPE3
tristate "TI PIPE3 PHY Driver"
@@ -84,13 +99,6 @@ config TI_PIPE3
This driver interacts with the "OMAP Control PHY Driver" to power
on/off the PHY.
-config PHY_TUSB1210
- tristate "TI TUSB1210 ULPI PHY module"
- depends on USB_ULPI_BUS
- select GENERIC_PHY
- help
- Support for TI TUSB1210 USB ULPI PHY.
-
config TWL4030_USB
tristate "TWL4030 USB Transceiver Driver"
depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
@@ -103,11 +111,3 @@ config TWL4030_USB
family chips (including the TWL5030 and TPS659x0 devices).
This transceiver supports high and full speed devices plus,
in host mode, low speed.
-
-config PHY_TI_GMII_SEL
- tristate
- select GENERIC_PHY
- select REGMAP
- help
- This driver supports configuring of the TI CPSW Port mode depending on
- the Ethernet PHY connected to the CPSW Port.
diff --git a/drivers/phy/ti/Makefile b/drivers/phy/ti/Makefile
index dcba2571c9bd..975fb8448ba5 100644
--- a/drivers/phy/ti/Makefile
+++ b/drivers/phy/ti/Makefile
@@ -1,11 +1,11 @@
# SPDX-License-Identifier: GPL-2.0
-obj-$(CONFIG_PHY_DA8XX_USB) += phy-da8xx-usb.o
-obj-$(CONFIG_PHY_DM816X_USB) += phy-dm816x-usb.o
obj-$(CONFIG_OMAP_CONTROL_PHY) += phy-omap-control.o
obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
-obj-$(CONFIG_TI_PIPE3) += phy-ti-pipe3.o
-obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
-obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
obj-$(CONFIG_PHY_AM654_SERDES) += phy-am654-serdes.o
-obj-$(CONFIG_PHY_TI_GMII_SEL) += phy-gmii-sel.o
+obj-$(CONFIG_PHY_DA8XX_USB) += phy-da8xx-usb.o
+obj-$(CONFIG_PHY_DM816X_USB) += phy-dm816x-usb.o
obj-$(CONFIG_PHY_J721E_WIZ) += phy-j721e-wiz.o
+obj-$(CONFIG_PHY_TI_GMII_SEL) += phy-gmii-sel.o
+obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
+obj-$(CONFIG_TI_PIPE3) += phy-ti-pipe3.o
+obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
--
2.25.1
More information about the linux-phy
mailing list