[PATCH v3 1/2] dt-bindings: phy: qcom: Add CSI2 C-PHY/DPHY schema

[Vijay Kumar Tumati]

Hi Bryan,

On 2/26/2026 4:34 AM, Bryan O'Donoghue wrote:
> Add a base schema initially compatible with x1e80100 to describe MIPI CSI2
> PHY devices.
> 
> The hardware can support both C-PHY and D-PHY modes. The CSIPHY devices
> have their own pinouts on the SoC as well as their own individual voltage
> rails.
> 
> The need to model voltage rails on a per-PHY basis leads us to define
> CSIPHY devices as individual nodes.
> 
> Two nice outcomes in terms of schema and DT arise from this change.
> 
> 1. The ability to define on a per-PHY basis voltage rails.
> 2. The ability to require those voltage.
> 
> We have had a complete bodge upstream for this where a single set of
> voltage rail for all CSIPHYs has been buried inside of CAMSS.
> 
> Much like the I2C bus which is dedicated to Camera sensors - the CCI bus in
> CAMSS parlance, the CSIPHY devices should be individually modelled.
> 
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue at linaro.org>
> ---
>   .../bindings/phy/qcom,x1e80100-csi2-phy.yaml       | 114 +++++++++++++++++++++
>   1 file changed, 114 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml
> new file mode 100644
> index 0000000000000..c937d26ccbda9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml
> @@ -0,0 +1,114 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/phy/qcom,x1e80100-csi2-phy.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm CSI2 PHY
> +
> +maintainers:
> +  - Bryan O'Donoghue <bod at kernel.org>
> +
> +description:
> +  Qualcomm MIPI CSI2 C-PHY/D-PHY combination PHY. Connects MIPI CSI2 sensors
> +  to Qualcomm's Camera CSI Decoder. The PHY supports both C-PHY and D-PHY
> +  modes.
> +
> +properties:
> +  compatible:
> +    const: qcom,x1e80100-csi2-phy
> +
> +  reg:
> +    maxItems: 1
> +
> +  "#phy-cells":
> +    const: 1
> +
> +  clocks:
> +    maxItems: 4
> +
> +  clock-names:
> +    items:
> +      - const: csiphy
> +      - const: csiphy_timer
> +      - const: camnoc_axi
> +      - const: cpas_ahb
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  operating-points-v2:
> +    maxItems: 1
> +
> +  power-domains:
> +    maxItems: 1
> +
> +  vdda-0p8-supply:
> +    description: Phandle to a 0.8V regulator supply to a PHY.
> +
> +  vdda-1p2-supply:
> +    description: Phandle to 1.2V regulator supply to a PHY.
> +
> +required:
> +  - compatible
> +  - reg
> +  - "#phy-cells"
> +  - clocks
> +  - clock-names
> +  - interrupts
> +  - operating-points-v2
> +  - power-domains
> +  - vdda-0p8-supply
> +  - vdda-1p2-supply
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/clock/qcom,x1e80100-camcc.h>
> +    #include <dt-bindings/clock/qcom,x1e80100-gcc.h>
> +    #include <dt-bindings/phy/phy.h>
> +
> +    csiphy at ace4000 {
> +        compatible = "qcom,x1e80100-csi2-phy";
> +        reg = <0x0ace4000 0x2000>;
> +        #phy-cells = <1>;
> +
> +        clocks = <&camcc CAM_CC_CSIPHY0_CLK>,
> +                 <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
> +                 <&camcc CAM_CC_CAMNOC_AXI_RT_CLK>,
> +                 <&camcc CAM_CC_CPAS_AHB_CLK>;
> +        clock-names = "csiphy",
> +                      "csiphy_timer",
> +                      "camnoc_axi",
> +                      "cpas_ahb";
> +
> +        operating-points-v2 = <&csiphy_opp_table>;
> +
> +        interrupts = <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>;
> +
> +        power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
As we are cleaning up the PHY device nodes, we should consider fixing 
the power domains as well. Although TOP GDSC is defined as a power 
domain, it is not the power source for the PHY devices. Rather, it is 
the MMCX, MXC and optionally MXA based on the architecture (Refer to 
'Voltage rail' column for PHY clocks in IPCAT). There is no
parent-child relationship between the TOP GDSC and these in the clock 
driver and it was just working as the required power rails are getting 
enabled by/for other MM devices.
> +
> +        vdda-0p8-supply = <&vreg_l2c_0p8>;
> +        vdda-1p2-supply = <&vreg_l1c_1p2>;
> +    };
> +
> +    csiphy_opp_table: opp-table-csiphy {
> +        compatible = "operating-points-v2";
> +
> +        opp-300000000 {
> +            opp-hz = /bits/ 64 <300000000>;
> +            required-opps = <&rpmhpd_opp_low_svs_d1>;
> +        };
> +
> +        opp-400000000 {
> +            opp-hz = /bits/ 64 <400000000>;
> +            required-opps = <&rpmhpd_opp_low_svs>;
> +        };
> +
> +        opp-480000000 {
> +            opp-hz = /bits/ 64 <480000000>;
> +            required-opps = <&rpmhpd_opp_low_svs>;
> +        };
> +    };
> 
Thanks,
Vijay.