[PATCH RFC v4 9/9] arm64: dts: qcom: glymur: Wire PCIe3a/3b to shared Gen5x8 PHY

[Konrad Dybcio]

On 6/29/26 7:05 AM, Qiang Yu wrote:
> On Wed, Jun 17, 2026 at 01:19:49PM +0200, Konrad Dybcio wrote:
>> On 5/19/26 7:47 AM, Qiang Yu wrote:
>>> Glymur PCIe3 uses a single shared Gen5x8 QMP PHY block. Model PCIe3a and
>>> PCIe3b as consumers of that shared PHY provider instead of separate PHY
>>> nodes.
>>>
>>> Update the DTS wiring to:
>>> - point GCC PCIe3A/3B pipe parents to the shared PHY clock outputs
>>> - add PCIe3a controller node and route PCIe3a/PCIe3b port phys to
>>>   &pcie3_phy using two-cell PHY arguments
>>> - configure the shared PHY node with link-mode and dual pipe outputs
>>>
>>> Use QMP_PCIE_GLYMUR_MODE_* dt-binding macros for mode selection.
>>>
>>> Signed-off-by: Qiang Yu <qiang.yu at oss.qualcomm.com>
>>> ---
>>
>> [...]
>>
>>> +		pcie3a: pci at 1c10000 {
>>> +			device_type = "pci";
>>> +			compatible = "qcom,glymur-pcie", "qcom,pcie-x1e80100";
>>> +			reg = <0x0 0x01c10000 0x0 0x3000>,
>>> +			      <0x0 0x70000000 0x0 0xf20>,
>>> +			      <0x0 0x70000f40 0x0 0xa8>,
>>> +			      <0x0 0x70001000 0x0 0x4000>,
>>> +			      <0x0 0x70100000 0x0 0x100000>,
>>> +			      <0x0 0x01c13000 0x0 0x1000>;
>>> +			reg-names = "parf",
>>> +				    "dbi",
>>> +				    "elbi",
>>> +				    "atu",
>>> +				    "config",
>>> +				    "mhi";
>>> +			#address-cells = <3>;
>>> +			#size-cells = <2>;
>>> +			ranges = <0x01000000 0x0 0x00000000 0x0 0x70200000 0x0 0x100000>,
>>> +				 <0x02000000 0x0 0x70000000 0x0 0x70300000 0x0 0x3d00000>,
>>> +				 <0x03000000 0x7 0x00000000 0x7 0x00000000 0x0 0x40000000>,
>>> +				 <0x43000000 0x70 0x00000000 0x70 0x00000000 0x10 0x00000000>;
>>> +
>>> +			bus-range = <0 0xff>;
>>> +
>>> +			dma-coherent;
>>> +
>>> +			linux,pci-domain = <3>;
>>> +			num-lanes = <8>;
>>
>> Is it fine to keep num-lanes 8 here even for configurations with
>> bifurcated PHY?
>>
>> I would assume so, given essentially this is a x8 host, whose 4
>> lanes may simply be effectively NC 
>>
> Actually, on existing platforms, the PCIe3a and PCIe3b controllers are
> never enabled at the same time. When PCIe3a is exposed, it is always in an
> x8 slot. But if we have a x4+x4 platform in future, we can simply override
> num-lanes to 4 in the board.dts.

My question is whether that will be necessary - if yes, sure, we
can do it, but if not, we can conclude on this early and not have
to fight over it in a couple months

Konrad