[PATCH v3 2/4] dt-bindings: phy: qcom,qcs615-qmp-usb3-dp-phy: Add support for Shikra

[Krishna Kurapati]

On 5/27/2026 3:16 PM, Krzysztof Kozlowski wrote:
> On Wed, May 27, 2026 at 12:13:59AM +0530, Pratham Pratap wrote:
>> From: Krishna Kurapati <krishna.kurapati at oss.qualcomm.com>
>>
>> Declare the USB QMP Phy present on Shikra SoC. On this SoC, although
>> there are DP registers, the required internal pins have been removed
>> and hence DP wouldn't be operational.
>>
>> Shikra needs 3 resets (dp/ phy/ phy_phy) to be asserted and de-asserted
>> as per hardware recommendation. Extend the bindings to accommodate the
>> additional reset.
>>
>> Use QCS615 as a fallback since the software interface is compatible with
>> Shikra.
>>
>> Signed-off-by: Krishna Kurapati <krishna.kurapati at oss.qualcomm.com>
>> Signed-off-by: Pratham Pratap <pratham.pratap at oss.qualcomm.com>
>> ---
>>   .../bindings/phy/qcom,qcs615-qmp-usb3dp-phy.yaml    | 13 ++++++++++---
>>   1 file changed, 10 insertions(+), 3 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/phy/qcom,qcs615-qmp-usb3dp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qcs615-qmp-usb3dp-phy.yaml
>> index efb465c71c1b..65ae4c6e09db 100644
>> --- a/Documentation/devicetree/bindings/phy/qcom,qcs615-qmp-usb3dp-phy.yaml
>> +++ b/Documentation/devicetree/bindings/phy/qcom,qcs615-qmp-usb3dp-phy.yaml
>> @@ -16,8 +16,12 @@ description:
>>   
>>   properties:
>>     compatible:
>> -    enum:
>> -      - qcom,qcs615-qmp-usb3-dp-phy
>> +    oneOf:
>> +      - items:
>> +          - enum:
>> +              - qcom,shikra-qmp-usb3-dp-phy
>> +          - const: qcom,qcs615-qmp-usb3-dp-phy
>> +      - const: qcom,qcs615-qmp-usb3-dp-phy
>>   
>>     reg:
>>       maxItems: 1
>> @@ -33,12 +37,15 @@ properties:
>>         - const: pipe
>>   
>>     resets:
>> -    maxItems: 2
>> +    minItems: 2
>> +    maxItems: 3
> 
> So QCS615 has three resets now? This needs to be explained in the commit
> msg. Or fixed with constraints, see writing bindings.
> 

Ok, will separate out for Shikra and keep only two for Talos.

>>   
>>     reset-names:
>> +    minItems: 2
>>       items:
>>         - const: phy_phy
>>         - const: dp_phy
>> +      - const: phy
> 
> Not phy_phy_phy? Joking aside, you already have a phy - "phy_phy" - so
> this is not correct name. I don't know what is the correct name, though.
> Please consult device manual.
> 
The resets needed on Shikra are:

GCC_USB3PHY_PHY_PRIM_SP0_BCR
GCC_USB3_DP_PHY_PRIM_BCR
GCC_USB3_PHY_PRIM_SP0_BCR

Hence named the third one as "phy".

Regards,
Krishna,