[PATCH v12 1/2] dt-bindings: phy: qcom: Add CSI2 C-PHY/DPHY schema

[Vladimir Zapolskiy]

On 7/19/26 16:47, Bryan O'Donoghue wrote:
> Add a base schema for the MIPI CSI2 PHYs on Qualcomm SoCs. This PHY
> supports both DPHY and CPHY operation. A special mode of DPHY operation -
> called variously split-mode or combo-mode also allows for two sensors to be
> connected to one PHY.
> 
> The submitted binding here describes the DPHY modes of operation only. CPHY
> is left to future work.
> 
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski at oss.qualcomm.com>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue at linaro.org>
> ---
>   .../bindings/phy/qcom,x1e80100-csi2-phy.yaml       | 195 +++++++++++++++++++++
>   1 file changed, 195 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml
> new file mode 100644
> index 0000000000000..880fe602945cb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml
> @@ -0,0 +1,195 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/phy/qcom,x1e80100-csi2-phy.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm X1E80100 SoC CSI2 PHY
> +
> +maintainers:
> +  - Bryan O'Donoghue <bod at kernel.org>
> +
> +description:
> +  Qualcomm MIPI CSI2 C-PHY/D-PHY combination PHY. Connects MIPI CSI2 sensors
> +  to Qualcomm's Camera CSI Decoder. The PHY supports both C-PHY and D-PHY
> +  modes.
> +
> +properties:
> +  compatible:
> +    const: qcom,x1e80100-csi2-phy
> +
> +  reg:
> +    maxItems: 1
> +
> +  "#phy-cells":
> +    const: 1
> +    description:
> +      The single cell specifies the PHY operating mode.
> +

This has been reported before, #phy-cells shall be 0, the operation
mode is selected by bus-type of endpoints as it is described in
video-interfaces.yaml

Two competing values are redundant, the technical discussion has
not been started yet.

> +  clocks:
> +    maxItems: 3
> +
> +  clock-names:
> +    items:
> +      - const: core
> +      - const: timer
> +      - const: ahb
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  operating-points-v2: true
> +
> +  opp-table:
> +    type: object
> +
> +  power-domains:
> +    items:
> +      - description: Titan Top GDSC - Titan ISP Block, Global Distributed Switch Controller.
> +      - description: MMCX voltage rail
> +      - description: MXC or MXA voltage rail

Please double check that there is such voltage rail as MXA.

> +
> +  power-domain-names:
> +    items:
> +      - const: top
> +      - const: mmcx
> +      - const: mx
> +
> +  vdda-0p9-supply:
> +    description: Phandle to a 0.9V regulator supply to a PHY.
> +
> +  vdda-1p2-supply:
> +    description: Phandle to 1.2V regulator supply to a PHY.
> +
> +  ports:
> +    $ref: /schemas/graph.yaml#/properties/ports
> +
> +    properties:
> +      port at 0:
> +        $ref: /schemas/graph.yaml#/$defs/port-base
> +        description:
> +          Sensor input. Always present. A single sensor is described by a
> +          single endpoint with one to four data lanes. DPHY split mode,
> +          where two independent sensors share the same PHY, is described
> +          by two endpoints; endpoint at 0 with exactly two data-lanes and
> +          endpoint at 1 with exactly one data-lane.
> +        unevaluatedProperties: false
> +
> +        patternProperties:
> +          "^endpoint(@[0-9a-f]+)?$":

endpoint regexp is not corrected, this issue has been reported
previously.

> +            $ref: /schemas/media/video-interfaces.yaml#
> +            unevaluatedProperties: false
> +            properties:
> +              data-lanes:
> +                minItems: 1
> +                maxItems: 4
> +
> +            required:
> +              - data-lanes
> +              - remote-endpoint
> +
> +        allOf:
> +          - if:
> +              required:
> +                - endpoint at 1
> +            then:
> +              properties:
> +                endpoint at 0:
> +                  properties:
> +                    data-lanes:
> +                      minItems: 2
> +                      maxItems: 2
> +                endpoint at 1:
> +                  properties:
> +                    data-lanes:
> +                      maxItems: 1
> +              required:
> +                - endpoint at 0
> +
> +      port at 1:
> +        $ref: /schemas/graph.yaml#/properties/port
> +        description: Output to the CAMSS CSID controller.
> +
> +    required:
> +      - port at 0
> +      - port at 1
> +
> +required:
> +  - compatible
> +  - reg
> +  - "#phy-cells"
> +  - clocks
> +  - clock-names
> +  - interrupts
> +  - operating-points-v2
> +  - power-domains
> +  - power-domain-names
> +  - vdda-0p9-supply
> +  - vdda-1p2-supply
> +  - ports
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/clock/qcom,x1e80100-camcc.h>
> +    #include <dt-bindings/clock/qcom,x1e80100-gcc.h>
> +    #include <dt-bindings/power/qcom,rpmhpd.h>
> +
> +    phy at ace4000 {
> +        compatible = "qcom,x1e80100-csi2-phy";
> +        reg = <0x0ace4000 0x2000>;
> +        #phy-cells = <1>;
> +
> +        clocks = <&camcc CAM_CC_CSIPHY0_CLK>,
> +                 <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
> +                 <&camcc CAM_CC_CORE_AHB_CLK>;
> +        clock-names = "core",
> +                      "timer",
> +                      "ahb";
> +
> +        interrupts = <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>;
> +
> +        operating-points-v2 = <&csiphy_opp_table>;
> +
> +        power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>,
> +                        <&rpmhpd RPMHPD_MMCX>,
> +                        <&rpmhpd RPMHPD_MX>;
> +        power-domain-names = "top",
> +                             "mmcx",
> +                             "mx";
> +
> +        vdda-0p9-supply = <&vreg_l2c_0p9>;
> +        vdda-1p2-supply = <&vreg_l1c_1p2>;
> +
> +        ports {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            port at 0 {
> +                reg = <0>;
> +                csiphy0_in: endpoint {
> +                    data-lanes = <0 1 2 3>;

data-lanes values has not been corrected in accordance to linux-media
requirements.

> +                    remote-endpoint = <&sensor_out>;
> +                };
> +            };
> +
> +            port at 1 {
> +                reg = <1>;
> +                csiphy0_out: endpoint {
> +                    remote-endpoint = <&csid_in>;
> +                };
> +            };
> +        };
> +
> +        csiphy_opp_table: opp-table {
> +            compatible = "operating-points-v2";
> +
> +            opp-300000000 {
> +                opp-hz = /bits/ 64 <300000000>;
> +                required-opps = <&rpmhpd_opp_low_svs_d1>,
> +                                <&rpmhpd_opp_low_svs_d1>;
> +            };
> +        };
> +    };
> 

-- 
Best wishes,
Vladimir