[PATCH v3 1/3] dt-bindings: phy: nuvoton,ma35d1-usb2-phy: extend for dual-port and OTG

[Joey Lu]

The MA35D1 exposes two USB PHY ports (PHY0 and PHY1) managed by the
same hardware block (USBPMISCR register in the system-management syscon).
PHY0 is shared between the DWC2 gadget controller and EHCI0/OHCI0
through an automatic hardware mux that follows the USB ID pin; PHY1 is
dedicated to EHCI1/OHCI1.  Because both ports share the same register
topology a single binding and driver should cover both.

Changing '#phy-cells' from const: 0 to enum: [0, 1] lets consumers name
the port they need while preserving backward compatibility: boards already
using '#phy-cells = <0>' continue to validate and function unchanged.

The two new optional properties:
  - nuvoton,rcalcode: the resistor calibration trim code is determined at
    board design time to match the PCB trace impedance.
  - nuvoton,oc-active-high: the over-current detect polarity depends on
    the choice of VBUS power switch.

Signed-off-by: Joey Lu <a0987203069 at gmail.com>
---
 .../bindings/phy/nuvoton,ma35d1-usb2-phy.yaml | 45 +++++++++++++++++--
 1 file changed, 42 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/nuvoton,ma35d1-usb2-phy.yaml b/Documentation/devicetree/bindings/phy/nuvoton,ma35d1-usb2-phy.yaml
index fff858c909a0..191d1b2272ec 100644
--- a/Documentation/devicetree/bindings/phy/nuvoton,ma35d1-usb2-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/nuvoton,ma35d1-usb2-phy.yaml
@@ -8,6 +8,18 @@ title: Nuvoton MA35D1 USB2 phy
 
 maintainers:
   - Hui-Ping Chen <hpchen0nvt at gmail.com>
+  - Joey Lu <yclu4 at nuvoton.com>
+
+description:
+  USB 2.0 PHY for the Nuvoton MA35D1 SoC. The PHY node is a standalone
+  platform device that accesses the USB PHY control registers inside the
+  system-management syscon block via the nuvoton,sys phandle.
+
+  PHY0 is the OTG port whose signals are routed to either the DWC2 gadget
+  controller or the EHCI0/OHCI0 host controller by a hardware mux that
+  follows the USB ID pin automatically.
+
+  PHY1 is a dedicated host-only port used by EHCI1/OHCI1.
 
 properties:
   compatible:
@@ -15,7 +27,12 @@ properties:
       - nuvoton,ma35d1-usb2-phy
 
   "#phy-cells":
-    const: 0
+    enum: [0, 1]
+    description:
+      When 0, the node exposes PHY0 only and consumers reference it
+      with no cell argument. When 1, the single cell selects the port,
+      with 0 for the OTG port (USB0, shared with DWC2 gadget controller)
+      and 1 for the host-only port (USB1).
 
   clocks:
     maxItems: 1
@@ -23,7 +40,29 @@ properties:
   nuvoton,sys:
     $ref: /schemas/types.yaml#/definitions/phandle
     description:
-      phandle to syscon for checking the PHY clock status.
+      Phandle to the system-management syscon node providing access to the
+      USB PHY control registers.
+
+  nuvoton,rcalcode:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 2
+    maxItems: 2
+    items:
+      minimum: 0
+      maximum: 15
+    description:
+      Resistor calibration trim codes for PHY0 and PHY1 respectively.
+      Each 4-bit value is written to the RCALCODE field in USBPMISCR and
+      adjusts the PHY's internal termination resistance. Both entries must
+      be supplied when this property is present; when absent the hardware
+      reset default is used for each port.
+
+  nuvoton,oc-active-high:
+    type: boolean
+    description:
+      When present, the over-current detect input from the VBUS power switch
+      is treated as active-high. The default (property absent) is active-low.
+      This setting is shared by both USB host ports.
 
 required:
   - compatible
@@ -39,7 +78,7 @@ examples:
 
     usb_phy: usb-phy {
         compatible = "nuvoton,ma35d1-usb2-phy";
-        clocks = <&clk USBD_GATE>;
+        clocks = <&clk HUSBH0_GATE>;
         nuvoton,sys = <&sys>;
         #phy-cells = <0>;
     };
-- 
2.43.0