[PATCH V2 3/3] arm64: dts: freescale: Add chargebyte Charge Control Y

[Frank Li]

On Mon, Aug 31, 2026 at 03:47:15PM +0200, Stefan Wahren wrote:
> Am 31.08.26 um 11:04 schrieb sashiko-bot at kernel.org:
> > Thank you for your contribution! Sashiko AI review found 3 potential issue(s) to consider:
> > - [Medium] Missing GPIO initialization / Unused pin for X_nRST_LAN
> > - [Medium] Missing Pin Mux Configuration for USDHC2_VSELECT in default state
> > - [Low] DT Binding Violation: Undocumented compatible string 'microchip,mcp2542'
> > --
> >
> > commit c595019b7dc419cc298a111c2b215904a12f65e1
> > Author: Stefan Wahren <wahrenst at gmx.net>
> > arm64: dts: freescale: Add chargebyte Charge Control Y
> >
> > This commit introduces device tree support for the chargebyte Charge Control Y,
> > an Electrical Vehicle Supply Equipment for MCS charging stations based on the
> > phyCORE-i.MX 93 ARM SoM. It defines necessary pin multiplexing, peripherals
> > like CAN and Ethernet, and device-specific layouts.
> >
> > > diff --git a/arch/arm64/boot/dts/freescale/imx93-charge-control-y.dts b/arch/arm64/boot/dts/freescale/imx93-charge-control-y.dts
> > > new file mode 100644
> > > index 0000000000000..0405098cc05c4
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/freescale/imx93-charge-control-y.dts
> > [ ... ]
> >
> > > +	// Heartbeat LED of phyCore is not populated
> > > +	/delete-node/ leds;
> > > +
> > > +	flexcan1_tc: can-phy0 {
> > > +		compatible = "microchip,mcp2542", "ti,tcan1042";
> > [Severity: Low]
> > Is the "microchip,mcp2542" compatible string documented in any devicetree
> > binding schema?
> This is included in patch #2.
> > Using an undocumented compatible string here might cause `make dtbs_check`
> > validation tooling to fail.
> I verified this patch series with "make dtbs_check". False positive?
> >
> > > +		#phy-cells = <0>;
> > > +		max-bitrate = <1000000>;
> > > +	};
> > [ ... ]
> >
> > > +	pinctrl_flexcan1: flexcan1grp {
> > > +		fsl,pins = <
> > > +			MX93_PAD_PDM_BIT_STREAM0__CAN1_RX	0x139e
> > > +			MX93_PAD_PDM_CLK__CAN1_TX		0x1382
> > > +		>;
> > > +	};
> > > +
> > > +	pinctrl_gpio1: gpio1grp {
> > > +		fsl,pins = <
> > > +			MX93_PAD_I2C2_SDA__GPIO1_IO03		0x31e
> > [Severity: Medium]
> > Does the X_nRST_LAN reset pin (GPIO1_IO03) need a GPIO hog or a driver
> > consumer (e.g., via a reset-gpios property) in the device tree?
> >
> > Since the upstream lan865x SPI kernel driver does not parse or manage
> > reset-gpios, leaving its functional state unmanaged here might result in the
> > hardware reset pin floating or being left in an indeterminate state.
> >
> > Could this cause the LAN8651 Ethernet interface to fail to emerge from reset
> > and initialize properly on a cold boot?
> As already mentioned in the cover letter, I like to proceed with the version
> until the reset management is implemented in LAN8651.
> The pin is not floating because there is a pull resistor in hardware.
>
> Should I move the explanation to the commit message of this patch or add a
> comment in the DTS?

Comments in code.

Frank

> >
> > > +			MX93_PAD_PDM_BIT_STREAM1__GPIO1_IO10	0x382
> > > +		>;
> > > +	};
> > > +
> > > +	pinctrl_gpio4: gpio4grp {
> > [ ... ]
> >
> > > +	pinctrl_usdhc2_cd: usdhc2cdgrp {
> > > +		fsl,pins = <
> > > +			MX93_PAD_SD2_CD_B__GPIO3_IO00		0x31e
> > > +		>;
> > > +	};
> > > +
> > > +	/* need to config the SION for data and cmd pad, refer to ERR052021 */
> > > +	pinctrl_usdhc2_default: usdhc2grp {
> > > +		fsl,pins = <
> > > +			MX93_PAD_SD2_CLK__USDHC2_CLK		0x119e
> > > +			MX93_PAD_SD2_CMD__USDHC2_CMD		0x4000139e
> > > +			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x4000138e
> > > +			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x4000138e
> > > +			MX93_PAD_SD2_DATA2__USDHC2_DATA2	0x4000138e
> > > +			MX93_PAD_SD2_DATA3__USDHC2_DATA3	0x4000139e
> > [Severity: Medium]
> > Should MX93_PAD_SD2_VSELECT__USDHC2_VSELECT be included in this default
> > state group?
> >
> > The MMC core initially brings up the SD card in the default 3.3V state. Without
> > the USDHC2_VSELECT pad configured here, the controller might not be able to
> > actively manage the IO voltage selection in its default state.
> >
> > Could this absence lead to unpredictable external voltage regulator behavior or
> > SD card initialization failures?
> Nice catch, will fix it
>
> Best regards
> >
> > > +		>;
> > > +	};
> > > +
> > > +	/* need to config the SION for data and cmd pad, refer to ERR052021 */
> > > +	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
>