[PATCH v1 3/4] arm64: dts: qcom: Add PCIe 3 support for HAMOA-IOT-SOM platform

[Krishna Chaitanya Chundru]

On 9/22/2025 1:25 PM, Ziyue Zhang wrote:
> Update the HAMOA-IOT-SOM device tree to enable PCIe 3 support. Add perst
> wake and clkreq sideband signals and required regulators in PCIe3
> controller and PHY device tree node.
> 
> Signed-off-by: Ziyue Zhang <ziyue.zhang at oss.qualcomm.com
> ---
>   arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi | 70 +++++++++++++++++++++
>   1 file changed, 70 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi b/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi
> index 0c8ae34c1f37..7486204a4a46 100644
> --- a/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi
> +++ b/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi
> @@ -390,6 +390,53 @@ &gpu_zap_shader {
>   	firmware-name = "qcom/x1e80100/gen70500_zap.mbn";
>   };
>   
> +&pm8550ve_8_gpios {
> +	pcie_x8_12v: pcie-12v-default-state {
> +		pins = "gpio8";
> +		function = "normal";
> +		output-enable;
> +		output-high;
> +		bias-pull-down;
> +		power-source = <0>;
> +	};
> +};
> +
> +&pmc8380_3_gpios {
> +	pm_sde7_aux_3p3_en: pcie-aux-3p3-default-state {
> +		pins = "gpio8";
> +		function = "normal";
> +		output-enable;
> +		output-high;
> +		bias-pull-down;
> +		power-source = <0>;
> +	};
> +
> +	pm_sde7_main_3p3_en: pcie-main-3p3-default-state {
> +		pins = "gpio6";
> +		function = "normal";
> +		output-enable;
> +		output-high;
> +		bias-pull-down;
> +		power-source = <0>;
> +	};
> +};
Either squash patch 3/4 with 4/4 or move these pin configuration to
patch 4/4.

- Krishna Chaitanya.
> +
> +&pcie3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie3_default>;
> +	perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
> +	wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
> +
> +	status = "okay";
> +};
> +
> +&pcie3_phy {
> +	vdda-phy-supply = <&vreg_l3c_0p8>;
> +	vdda-pll-supply = <&vreg_l3e_1p2>;
> +
> +	status = "okay";
> +};
> +
>   &pcie4 {
>   	perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
>   	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
> @@ -471,6 +518,29 @@ &tlmm {
>   	gpio-reserved-ranges = <34 2>, /* TPM LP & INT */
>   			       <44 4>; /* SPI (TPM) */
>   
> +	pcie3_default: pcie3-default-state {
> +		clkreq-n-pins {
> +			pins = "gpio144";
> +			function = "pcie3_clk";
> +			drive-strength = <2>;
> +			bias-pull-up;
> +		};
> +
> +		perst-n-pins {
> +			pins = "gpio143";
> +			function = "gpio";
> +			drive-strength = <2>;
> +			bias-pull-down;
> +		};
> +
> +		wake-n-pins {
> +			pins = "gpio145";
> +			function = "gpio";
> +			drive-strength = <2>;
> +			bias-pull-up;
> +		};
> +	};
> +
>   	pcie4_default: pcie4-default-state {
>   		clkreq-n-pins {
>   			pins = "gpio147";