[PATCH v5 01/22] dt-bindings: mux: Remove nodename pattern constraints

[Rob Herring (Arm)]

On Thu, 27 Nov 2025 12:48:28 +0100, Tommaso Merciai wrote:
> The nodename pattern in  created an unnecessary restriction that forced
> all mux nodes to be named with the 'mux-controller' prefix.
> This prevented valid use cases where mux functionality is part of other
> hardware blocks that should use more specific naming conventions.
> 
> Remove the $nodename pattern constraints from both the 'select' keyword
> and the properties section of the mux-controller schema.
> 
> Reviewed-by: Conor Dooley <conor.dooley at microchip.com>
> Signed-off-by: Tommaso Merciai <tommaso.merciai.xr at bp.renesas.com>
> ---
> v4->v5:
>  - Added Reviewed-by tag from Conor Dooley.
> 
> v3->v4:
>  - New patch.
> 
>  Documentation/devicetree/bindings/mux/mux-controller.yaml | 6 ------
>  1 file changed, 6 deletions(-)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/slimbus/slimbus.example.dtb: slim at 28080000 (qcom,slim-ngd-v1.5.0): 'audio-codec at 1,0' does not match any of the regexes: '^pinctrl-[0-9]+$', '^slim@[0-9a-f]+$'
	from schema $id: http://devicetree.org/schemas/slimbus/qcom,slim-ngd.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/slimbus/slimbus.example.dtb: slim at 28080000 (qcom,slim-ngd-v1.5.0): #address-cells: 1 was expected
	from schema $id: http://devicetree.org/schemas/slimbus/qcom,slim-ngd.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/slimbus/slimbus.example.dtb: slim at 28080000 (qcom,slim-ngd-v1.5.0): 'dmas' is a required property
	from schema $id: http://devicetree.org/schemas/slimbus/qcom,slim-ngd.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/slimbus/slimbus.example.dtb: slim at 28080000 (qcom,slim-ngd-v1.5.0): 'dma-names' is a required property
	from schema $id: http://devicetree.org/schemas/slimbus/qcom,slim-ngd.yaml
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor at c263000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor at c263000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor at c265000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor at c265000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/d0518a64bac31a5a755471f79d6000aa81657503.1764241212.git.tommaso.merciai.xr@bp.renesas.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.