[PATCH V2 2/6] phy: qcom-qmp-ufs: Refactor phy_power_on and phy_calibrate callbacks

neil.armstrong at linaro.org neil.armstrong at linaro.org
Tue Mar 18 08:09:10 PDT 2025


On 18/03/2025 15:49, Nitin Rawat wrote:
> Commit 052553af6a31 ("ufs/phy: qcom: Refactor to use phy_init call")
> puts enabling regulators & clks, calibrating UFS PHY, starting serdes
> and polling PCS ready status into phy_power_on.
> 
> In Current code regulators enable, clks enable, calibrating UFS PHY,
> start_serdes and polling PCS_ready_status are part of phy_power_on.
> 
> UFS PHY registers are retained after power collapse, meaning calibrating
> UFS PHY, start_serdes and polling PCS_ready_status can be done only when
> hba is powered_on, and not needed every time when phy_power_on is called
> during resume. Hence keep the code which enables PHY's regulators & clks
> in phy_power_on and move the rest steps into phy_calibrate function.
> 
> Refactor the code to retain PHY regulators & clks in phy_power_on and
> move out rest of the code to new phy_calibrate function.
> 
> Co-developed-by: Can Guo <quic_cang at quicinc.com>
> Signed-off-by: Can Guo <quic_cang at quicinc.com>
> Signed-off-by: Nitin Rawat <quic_nitirawa at quicinc.com>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 18 ++----------------
>   1 file changed, 2 insertions(+), 16 deletions(-)
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> index bb836bc0f736..0089ee80f852 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> @@ -1796,7 +1796,7 @@ static int qmp_ufs_com_exit(struct qmp_ufs *qmp)
>   	return 0;
>   }
> 
> -static int qmp_ufs_init(struct phy *phy)
> +static int qmp_ufs_power_on(struct phy *phy)
>   {
>   	struct qmp_ufs *qmp = phy_get_drvdata(phy);
>   	const struct qmp_phy_cfg *cfg = qmp->cfg;
> @@ -1898,21 +1898,6 @@ static int qmp_ufs_exit(struct phy *phy)
>   	return 0;
>   }
> 
> -static int qmp_ufs_power_on(struct phy *phy)
> -{
> -	int ret;
> -
> -	ret = qmp_ufs_init(phy);
> -	if (ret)
> -		return ret;
> -
> -	ret = qmp_ufs_phy_calibrate(phy);
> -	if (ret)
> -		qmp_ufs_exit(phy);
> -
> -	return ret;
> -}
> -
>   static int qmp_ufs_disable(struct phy *phy)
>   {
>   	int ret;
> @@ -1942,6 +1927,7 @@ static int qmp_ufs_set_mode(struct phy *phy, enum phy_mode mode, int submode)
>   static const struct phy_ops qcom_qmp_ufs_phy_ops = {
>   	.power_on	= qmp_ufs_power_on,
>   	.power_off	= qmp_ufs_disable,
> +	.calibrate	= qmp_ufs_phy_calibrate,

Ok so this will break the UFS until patch 5 is applied,
breaking bisectability.

Make sure UFS host driver calls calibrate first, and then
do the refactor in the PHY driver.

And either all would go in a single tree or either PHY
or SCSI maintainer would need to provide an immutable
branch for the final merge.

>   	.set_mode	= qmp_ufs_set_mode,
>   	.owner		= THIS_MODULE,
>   };
> --
> 2.48.1
> 
> 




More information about the linux-phy mailing list