[PATCH v1 2/7] nvmem: qcom-spmi-sdam: Migrate to devm_spmi_subdevice_alloc_and_add()

[AngeloGioacchino Del Regno]

Il 21/07/25 15:56, Casey Connolly ha scritto:
> 
> 
> On 21/07/2025 14:45, AngeloGioacchino Del Regno wrote:
>> Il 21/07/25 12:44, Casey Connolly ha scritto:
>>> Hi Angelo,
>>>
>>> On 21/07/2025 09:55, AngeloGioacchino Del Regno wrote:
>>>> Some Qualcomm PMICs integrate a SDAM device, internally located in
>>>> a specific address range reachable through SPMI communication.
>>>>
>>>> Instead of using the parent SPMI device (the main PMIC) as a kind
>>>> of syscon in this driver, register a new SPMI sub-device for SDAM
>>>> and initialize its own regmap with this sub-device's specific base
>>>> address, retrieved from the devicetree.
>>>>
>>>> This allows to stop manually adding the register base address to
>>>> every R/W call in this driver, as this can be, and is now, handled
>>>> by the regmap API instead.
>>>
>>> This is honestly a really nice improvement :D>
>>
>> Thanks! :-D
>>
>>>> Signed-off-by: AngeloGioacchino Del Regno
>>>> <angelogioacchino.delregno at collabora.com>
>>>> ---
>>>>    drivers/nvmem/qcom-spmi-sdam.c | 41 +++++++++++++++++++++++++---------
>>>>    1 file changed, 30 insertions(+), 11 deletions(-)
>>>>
>>>> diff --git a/drivers/nvmem/qcom-spmi-sdam.c b/drivers/nvmem/qcom-
>>>> spmi-sdam.c
>>>> index 4f1cca6eab71..1b80e8563a33 100644
>>>> --- a/drivers/nvmem/qcom-spmi-sdam.c
>>>> +++ b/drivers/nvmem/qcom-spmi-sdam.c
>>>> @@ -9,6 +9,7 @@
>>>>    #include <linux/nvmem-provider.h>
>>>>    #include <linux/platform_device.h>
>>>>    #include <linux/regmap.h>
>>>> +#include <linux/spmi.h>
>>>>      #define SDAM_MEM_START            0x40
>>>>    #define REGISTER_MAP_ID            0x40
>>>> @@ -20,7 +21,6 @@
>>>>    struct sdam_chip {
>>>>        struct regmap            *regmap;
>>>>        struct nvmem_config        sdam_config;
>>>> -    unsigned int            base;
>>>>        unsigned int            size;
>>>>    };
>>>>    @@ -73,7 +73,7 @@ static int sdam_read(void *priv, unsigned int
>>>> offset, void *val,
>>>>            return -EINVAL;
>>>>        }
>>>>    -    rc = regmap_bulk_read(sdam->regmap, sdam->base + offset, val,
>>>> bytes);
>>>> +    rc = regmap_bulk_read(sdam->regmap, offset, val, bytes);
>>>>        if (rc < 0)
>>>>            dev_err(dev, "Failed to read SDAM offset %#x len=%zd,
>>>> rc=%d\n",
>>>>                            offset, bytes, rc);
>>>> @@ -100,7 +100,7 @@ static int sdam_write(void *priv, unsigned int
>>>> offset, void *val,
>>>>            return -EINVAL;
>>>>        }
>>>>    -    rc = regmap_bulk_write(sdam->regmap, sdam->base + offset, val,
>>>> bytes);
>>>> +    rc = regmap_bulk_write(sdam->regmap, offset, val, bytes);
>>>>        if (rc < 0)
>>>>            dev_err(dev, "Failed to write SDAM offset %#x len=%zd,
>>>> rc=%d\n",
>>>>                            offset, bytes, rc);
>>>> @@ -110,28 +110,47 @@ static int sdam_write(void *priv, unsigned int
>>>> offset, void *val,
>>>>      static int sdam_probe(struct platform_device *pdev)
>>>>    {
>>>> +    struct regmap_config sdam_regmap_config = {
>>>> +        .reg_bits = 16,
>>>> +        .val_bits = 16,
>>>
>>> I believe registers are 8 bits wide, at least on Qualcomm platforms.
>>>
>>
>> I used 16 because usually that's the usual default for SPMI - but if
>> you're sure
>> about Qualcomm platforms having 8-bits wide registers and you can
>> confirm that,
>> I can change both of those to 8 in a jiffy.
> 
> reg_bits should be 16, only val_bits needs changing.
> 
>>
>> I anyway have to send a v2 because I forgot an error check - so changing
>> this is
>> not a problem at all for me.
>>
>> But.
>>
>> Before me changing - can you please please please double check and confirm?
>>
>> If you can also check the register width of the others that I converted,
>> I'd really
>> appreciate that (I have no datasheets for qcom so it's a bit of a
>> guessing game for
>> me here... :-P), just so that we get everything right from the get-
>> go ... even if
>> a mismatch wouldn't really cause issues in the current state of things.
>>
>> That's because - I just noticed - in qcom-spmi-pmic.c, reg_bits is 16,
>> but val_bits
>> is 8 (which basically means "the registers are 16-bits wide, but we
>> always only
>> care about the lower 8 bits).
> 
> yeah that's right, so as of today where we don't have the subdevices we
> always get 8 bit values from the registers.
> 
> I don't have so much access to docs anymore but I only ever remember
> seeing 8 bit wide registers on Qualcomm PMICs, I've never seen anything
> wider, I can think of a few drivers where changing this to 16 would for
> sure cause havoc.
> 

Yeah, right. I'm changing all val_bits to 8 to ensure compatibility.

Cheers,
Angelo