[PATCH 4/5] arm64: dts: qcom: qcs8300: enable pcie0 for QCS8300

[Konrad Dybcio]

On 14.11.2024 10:54 AM, Ziyue Zhang wrote:
> Add configurations in devicetree for PCIe0, including registers, clocks,
> interrupts and phy setting sequence.
> 
> Signed-off-by: Ziyue Zhang <quic_ziyuzhan at quicinc.com>
> ---
>  arch/arm64/boot/dts/qcom/qcs8300-ride.dts |  44 +++++-
>  arch/arm64/boot/dts/qcom/qcs8300.dtsi     | 176 ++++++++++++++++++++++

This implies this patch should be two separate ones


[...]


> +&tlmm {
> +	pcie0_default_state: pcie0-default-state {
> +		perst-pins {
> +			pins = "gpio2";
> +			function = "gpio";
> +			drive-strength = <2>;
> +			bias-pull-down;
> +		};
> +
> +		clkreq-pins {
> +			pins = "gpio1";
> +			function = "pcie0_clkreq";
> +			drive-strength = <2>;
> +			bias-pull-up;
> +		};
> +
> +		wake-pins {
> +			pins = "gpio0";

Sorting these in an increasing order would be welcome


>  
> +		pcie0: pci at 1c00000 {
> +			compatible = "qcom,pcie-qcs8300","qcom,pcie-sa8775p";

Missing ' ' after ','

> +			reg = <0x0 0x01c00000 0x0 0x3000>,
> +			      <0x0 0x40000000 0x0 0xf20>,
> +			      <0x0 0x40000f20 0x0 0xa8>,
> +			      <0x0 0x40001000 0x0 0x4000>,
> +			      <0x0 0x40100000 0x0 0x100000>,
> +			      <0x0 0x01c03000 0x0 0x1000>;
> +
> +			reg-names = "parf",
> +				    "dbi",
> +				    "elbi",
> +				    "atu",
> +				    "config",
> +				    "mhi";
> +
> +			device_type = "pci";

Please try to match the style in x1e80100, it's mostly coherent but
things like newlines differ, which is tiny but mildly annoying

> +
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,
> +				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;

Looks like there's a bit more space in there
> +			bus-range = <0x00 0xff>;
> +
> +			dma-coherent;
> +
> +			linux,pci-domain = <0>;
> +			num-lanes = <2>;
> +
> +			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
> +
> +			interrupt-names = "msi0",
> +					  "msi1",
> +					  "msi2",
> +					  "msi3",
> +					  "msi4",
> +					  "msi5",
> +					  "msi6",
> +					  "msi7";

Please also add a "global" interrupt.. looks like it's GIC_SPI 166, but
please confirm

> +
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc GIC_SPI 434 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 2 &intc GIC_SPI 435 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 3 &intc GIC_SPI 438 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 4 &intc GIC_SPI 439 IRQ_TYPE_LEVEL_HIGH>;
> +
> +			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
> +				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
> +				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
> +				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
> +				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>;
> +
> +			clock-names = "aux",
> +				      "cfg",
> +				      "bus_master",
> +				      "bus_slave",
> +				      "slave_q2a";
> +
> +			assigned-clocks = <&gcc GCC_PCIE_0_AUX_CLK>;
> +			assigned-clock-rates = <19200000>;
> +
> +			interconnects = <&pcie_anoc MASTER_PCIE_0 0 &mc_virt SLAVE_EBI1 0>,

QCOM_ICC_TAG_ALWAYS

> +					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_0 0>;

QCOM_ICC_TAG_ACTIVE_ONLY

[...]

> +
> +			pcieport0: pcie at 0 {
> +				device_type = "pci";
> +				reg = <0x0 0x0 0x0 0x0 0x0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				ranges;
> +				bus-range = <0x01 0xff>;
> +			};

Are you going to use this? If not, please drop

> +		};
> +
> +		pcie0_phy: phy at 1c04000 {
> +			compatible = "qcom,qcs8300-qmp-gen4x2-pcie-phy";
> +			reg = <0x0 0x1c04000 0x0 0x2000>;
> +
> +			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,

This clock goes to the RC, it should be _PHY_AUX (which you put below
as phy_aux), please replace it.

> +				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
> +				 <&gcc GCC_PCIE_CLKREF_EN>,
> +				 <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>,
> +				 <&gcc GCC_PCIE_0_PIPE_CLK>,
> +				 <&gcc GCC_PCIE_0_PIPEDIV2_CLK>,
> +				 <&gcc GCC_PCIE_0_PHY_AUX_CLK>;
> +
> +			clock-names = "aux",
> +				      "cfg_ahb",
> +				      "ref",
> +				      "rchng",
> +				      "pipe",
> +				      "pipediv2",
> +				      "phy_aux";

Konrad