[PATCH] phy: qcom: qmp-pcie: Configure all tables on port B PHY

[Johan Hovold]

On Fri, Jul 26, 2024 at 11:09:14AM +0300, Abel Vesa wrote:
> From: Qiang Yu <quic_qianyu at quicinc.com>
> 
> Currently, only the RX and TX tables are written to the second PHY
> (port B) when the 4-lanes mode is configured, but according to Qualcomm
> internal documentation, the pcs, pcs_misc, serdes and ln_shrd tables need
> to be written as well.
> 
> Signed-off-by: Qiang Yu <quic_qianyu at quicinc.com>
> Signed-off-by: Abel Vesa <abel.vesa at linaro.org>
> ---
>  drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 14 +++++++++++++-
>  1 file changed, 13 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> index 5b36cc7ac78b..fd59ebd32f5f 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> @@ -3660,18 +3660,30 @@ static void qmp_pcie_init_port_b(struct qmp_pcie *qmp, const struct qmp_phy_cfg_
>  {
>  	const struct qmp_phy_cfg *cfg = qmp->cfg;
>  	const struct qmp_pcie_offsets *offs = cfg->offsets;
> -	void __iomem *tx3, *rx3, *tx4, *rx4;
> +	void __iomem *tx3, *rx3, *tx4, *rx4, *pcs, *pcs_misc, *ln_shrd, *serdes;

Please order these as serdes, tx/rx, pcs, pcs_misc, ln_shrd so that it
matches the order port_a is programmed (even if the hardware doesn't
care about this).

>  
>  	tx3 = qmp->port_b + offs->tx;
>  	rx3 = qmp->port_b + offs->rx;
>  	tx4 = qmp->port_b + offs->tx2;
>  	rx4 = qmp->port_b + offs->rx2;
> +	serdes = qmp->port_b + offs->serdes;

And use the same order here (move serdes above tx3).

> +	pcs = qmp->port_b + offs->pcs;
> +	pcs_misc = qmp->port_b + offs->pcs_misc;
> +	ln_shrd = qmp->port_b + offs->ln_shrd;

>  	qmp_configure_lane(tx3, tbls->tx, tbls->tx_num, 1);
>  	qmp_configure_lane(rx3, tbls->rx, tbls->rx_num, 1);
>  
>  	qmp_configure_lane(tx4, tbls->tx, tbls->tx_num, 2);
>  	qmp_configure_lane(rx4, tbls->rx, tbls->rx_num, 2);
> +
> +	qmp_configure(serdes, tbls->serdes, tbls->serdes_num);
> +	qmp_configure(serdes, cfg->serdes_4ln_tbl, cfg->serdes_4ln_num);

And here (e.g. move serdes above tx3).

> +
> +	qmp_configure(pcs, tbls->pcs, tbls->pcs_num);
> +	qmp_configure(pcs_misc, tbls->pcs_misc, tbls->pcs_misc_num);
> +
> +	qmp_configure(ln_shrd, tbls->ln_shrd, tbls->ln_shrd_num);
>  }

Johan