[PATCH v4 3/3] phy: qcom: edp: Add v6 specific ops and X1E80100 platform support
Abel Vesa
abel.vesa at linaro.org
Tue Feb 20 14:05:23 PST 2024
Add v6 HW support by implementing the version ops. Add the X1E80100
compatible and match config as it is v6.
Signed-off-by: Abel Vesa <abel.vesa at linaro.org>
---
drivers/phy/qualcomm/phy-qcom-edp.c | 180 ++++++++++++++++++++++++++++++++++++
1 file changed, 180 insertions(+)
diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c
index 9bbf977c7b4e..da2b32fb5b45 100644
--- a/drivers/phy/qualcomm/phy-qcom-edp.c
+++ b/drivers/phy/qualcomm/phy-qcom-edp.c
@@ -24,6 +24,7 @@
#include "phy-qcom-qmp-dp-phy.h"
#include "phy-qcom-qmp-qserdes-com-v4.h"
+#include "phy-qcom-qmp-qserdes-com-v6.h"
/* EDP_PHY registers */
#define DP_PHY_CFG 0x0010
@@ -532,6 +533,184 @@ static const struct qcom_edp_phy_cfg sc8280xp_edp_phy_cfg = {
.ver_ops = &qcom_edp_phy_ops_v4,
};
+static int qcom_edp_phy_power_on_v6(const struct qcom_edp *edp)
+{
+ u32 val;
+
+ writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
+ DP_PHY_PD_CTL_LANE_0_1_PWRDN | DP_PHY_PD_CTL_LANE_2_3_PWRDN |
+ DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
+ edp->edp + DP_PHY_PD_CTL);
+ writel(0xfc, edp->edp + DP_PHY_MODE);
+
+ return readl_poll_timeout(edp->pll + QSERDES_V6_COM_CMN_STATUS,
+ val, val & BIT(7), 5, 200);
+}
+
+static int qcom_edp_phy_com_resetsm_cntrl_v6(const struct qcom_edp *edp)
+{
+ u32 val;
+
+ writel(0x20, edp->pll + QSERDES_V6_COM_RESETSM_CNTRL);
+
+ return readl_poll_timeout(edp->pll + QSERDES_V6_COM_C_READY_STATUS,
+ val, val & BIT(0), 500, 10000);
+}
+
+static int qcom_edp_com_bias_en_clkbuflr_v6(const struct qcom_edp *edp)
+{
+ /* Turn on BIAS current for PHY/PLL */
+ writel(0x1f, edp->pll + QSERDES_V6_COM_PLL_BIAS_EN_CLK_BUFLR_EN);
+
+ return 0;
+}
+
+static int qcom_edp_com_configure_ssc_v6(const struct qcom_edp *edp)
+{
+ const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
+ u32 step1;
+ u32 step2;
+
+ switch (dp_opts->link_rate) {
+ case 1620:
+ case 2700:
+ case 8100:
+ step1 = 0x92;
+ step2 = 0x01;
+ break;
+
+ case 5400:
+ step1 = 0x18;
+ step2 = 0x02;
+ break;
+
+ default:
+ /* Other link rates aren't supported */
+ return -EINVAL;
+ }
+
+ writel(0x01, edp->pll + QSERDES_V6_COM_SSC_EN_CENTER);
+ writel(0x00, edp->pll + QSERDES_V6_COM_SSC_ADJ_PER1);
+ writel(0x36, edp->pll + QSERDES_V6_COM_SSC_PER1);
+ writel(0x01, edp->pll + QSERDES_V6_COM_SSC_PER2);
+ writel(step1, edp->pll + QSERDES_V6_COM_SSC_STEP_SIZE1_MODE0);
+ writel(step2, edp->pll + QSERDES_V6_COM_SSC_STEP_SIZE2_MODE0);
+
+ return 0;
+}
+
+static int qcom_edp_com_configure_pll_v6(const struct qcom_edp *edp)
+{
+ const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
+ u32 div_frac_start2_mode0;
+ u32 div_frac_start3_mode0;
+ u32 dec_start_mode0;
+ u32 lock_cmp1_mode0;
+ u32 lock_cmp2_mode0;
+ u32 code1_mode0;
+ u32 code2_mode0;
+ u32 hsclk_sel;
+
+ switch (dp_opts->link_rate) {
+ case 1620:
+ hsclk_sel = 0x5;
+ dec_start_mode0 = 0x34;
+ div_frac_start2_mode0 = 0xc0;
+ div_frac_start3_mode0 = 0x0b;
+ lock_cmp1_mode0 = 0x37;
+ lock_cmp2_mode0 = 0x04;
+ code1_mode0 = 0x71;
+ code2_mode0 = 0x0c;
+ break;
+
+ case 2700:
+ hsclk_sel = 0x3;
+ dec_start_mode0 = 0x34;
+ div_frac_start2_mode0 = 0xc0;
+ div_frac_start3_mode0 = 0x0b;
+ lock_cmp1_mode0 = 0x07;
+ lock_cmp2_mode0 = 0x07;
+ code1_mode0 = 0x71;
+ code2_mode0 = 0x0c;
+ break;
+
+ case 5400:
+ hsclk_sel = 0x1;
+ dec_start_mode0 = 0x46;
+ div_frac_start2_mode0 = 0x00;
+ div_frac_start3_mode0 = 0x05;
+ lock_cmp1_mode0 = 0x0f;
+ lock_cmp2_mode0 = 0x0e;
+ code1_mode0 = 0x97;
+ code2_mode0 = 0x10;
+ break;
+
+ case 8100:
+ hsclk_sel = 0x0;
+ dec_start_mode0 = 0x34;
+ div_frac_start2_mode0 = 0xc0;
+ div_frac_start3_mode0 = 0x0b;
+ lock_cmp1_mode0 = 0x17;
+ lock_cmp2_mode0 = 0x15;
+ code1_mode0 = 0x71;
+ code2_mode0 = 0x0c;
+ break;
+
+ default:
+ /* Other link rates aren't supported */
+ return -EINVAL;
+ }
+
+ writel(0x01, edp->pll + QSERDES_V6_COM_SVS_MODE_CLK_SEL);
+ writel(0x0b, edp->pll + QSERDES_V6_COM_SYSCLK_EN_SEL);
+ writel(0x02, edp->pll + QSERDES_V6_COM_SYS_CLK_CTRL);
+ writel(0x0c, edp->pll + QSERDES_V6_COM_CLK_ENABLE1);
+ writel(0x06, edp->pll + QSERDES_V6_COM_SYSCLK_BUF_ENABLE);
+ writel(0x30, edp->pll + QSERDES_V6_COM_CLK_SELECT);
+ writel(hsclk_sel, edp->pll + QSERDES_V6_COM_HSCLK_SEL_1);
+ writel(0x07, edp->pll + QSERDES_V6_COM_PLL_IVCO);
+ writel(0x08, edp->pll + QSERDES_V6_COM_LOCK_CMP_EN);
+ writel(0x36, edp->pll + QSERDES_V6_COM_PLL_CCTRL_MODE0);
+ writel(0x16, edp->pll + QSERDES_V6_COM_PLL_RCTRL_MODE0);
+ writel(0x06, edp->pll + QSERDES_V6_COM_CP_CTRL_MODE0);
+ writel(dec_start_mode0, edp->pll + QSERDES_V6_COM_DEC_START_MODE0);
+ writel(0x00, edp->pll + QSERDES_V6_COM_DIV_FRAC_START1_MODE0);
+ writel(div_frac_start2_mode0, edp->pll + QSERDES_V6_COM_DIV_FRAC_START2_MODE0);
+ writel(div_frac_start3_mode0, edp->pll + QSERDES_V6_COM_DIV_FRAC_START3_MODE0);
+ writel(0x12, edp->pll + QSERDES_V6_COM_CMN_CONFIG_1);
+ writel(0x3f, edp->pll + QSERDES_V6_COM_INTEGLOOP_GAIN0_MODE0);
+ writel(0x00, edp->pll + QSERDES_V6_COM_INTEGLOOP_GAIN1_MODE0);
+ writel(0x00, edp->pll + QSERDES_V6_COM_VCO_TUNE_MAP);
+ writel(lock_cmp1_mode0, edp->pll + QSERDES_V6_COM_LOCK_CMP1_MODE0);
+ writel(lock_cmp2_mode0, edp->pll + QSERDES_V6_COM_LOCK_CMP2_MODE0);
+
+ writel(0x0a, edp->pll + QSERDES_V6_COM_BG_TIMER);
+ writel(0x14, edp->pll + QSERDES_V6_COM_PLL_CORE_CLK_DIV_MODE0);
+ writel(0x00, edp->pll + QSERDES_V6_COM_VCO_TUNE_CTRL);
+ writel(0x1f, edp->pll + QSERDES_V6_COM_PLL_BIAS_EN_CLK_BUFLR_EN);
+ writel(0x0f, edp->pll + QSERDES_V6_COM_CORE_CLK_EN);
+ writel(0xa0, edp->pll + QSERDES_V6_COM_VCO_TUNE1_MODE0);
+ writel(0x03, edp->pll + QSERDES_V6_COM_VCO_TUNE2_MODE0);
+
+ writel(code1_mode0, edp->pll + QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE1_MODE0);
+ writel(code2_mode0, edp->pll + QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE2_MODE0);
+
+ return 0;
+}
+
+static const struct phy_ver_ops qcom_edp_phy_ops_v6 = {
+ .com_power_on = qcom_edp_phy_power_on_v6,
+ .com_resetsm_cntrl = qcom_edp_phy_com_resetsm_cntrl_v6,
+ .com_bias_en_clkbuflr = qcom_edp_com_bias_en_clkbuflr_v6,
+ .com_configure_pll = qcom_edp_com_configure_pll_v6,
+ .com_configure_ssc = qcom_edp_com_configure_ssc_v6,
+};
+
+static struct qcom_edp_phy_cfg x1e80100_phy_cfg = {
+ .swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg,
+ .ver_ops = &qcom_edp_phy_ops_v6,
+};
+
static int qcom_edp_phy_power_on(struct phy *phy)
{
const struct qcom_edp *edp = phy_get_drvdata(phy);
@@ -933,6 +1112,7 @@ static const struct of_device_id qcom_edp_phy_match_table[] = {
{ .compatible = "qcom,sc8180x-edp-phy", .data = &sc7280_dp_phy_cfg, },
{ .compatible = "qcom,sc8280xp-dp-phy", .data = &sc8280xp_dp_phy_cfg, },
{ .compatible = "qcom,sc8280xp-edp-phy", .data = &sc8280xp_edp_phy_cfg, },
+ { .compatible = "qcom,x1e80100-dp-phy", .data = &x1e80100_phy_cfg, },
{ }
};
MODULE_DEVICE_TABLE(of, qcom_edp_phy_match_table);
--
2.34.1
More information about the linux-phy
mailing list