[PATCH v3 07/15] drm/bridge: analogix_dp: Add support for phy configuration.
Dmitry Baryshkov
dmitry.baryshkov at linaro.org
Thu Dec 19 21:37:11 PST 2024
On Fri, 20 Dec 2024 at 05:37, Damon Ding <damon.ding at rock-chips.com> wrote:
>
> Hi Dmitry,
>
> On 2024/12/20 8:13, Dmitry Baryshkov wrote:
> > On Thu, Dec 19, 2024 at 04:05:56PM +0800, Damon Ding wrote:
> >> Add support to configurate link rate, lane count, voltage swing and
> >> pre-emphasis with phy_configure(). It is helpful in application scenarios
> >> where analogix controller is mixed with the phy of other vendors.
> >>
> >> Signed-off-by: Damon Ding <damon.ding at rock-chips.com>
> >>
> >> ---
> >>
> >> Changes in v2:
> >> - remove needless assignments for phy_configure()
> >> - remove unnecessary changes for phy_power_on()/phy_power_off()
> >> ---
> >> .../drm/bridge/analogix/analogix_dp_core.c | 1 +
> >> .../gpu/drm/bridge/analogix/analogix_dp_reg.c | 56 +++++++++++++++++++
> >> 2 files changed, 57 insertions(+)
> >>
> >> diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
> >> index 6f10d88a34c5..9429c50cc1bc 100644
> >> --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
> >> +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
> >> @@ -1696,6 +1696,7 @@ int analogix_dp_resume(struct analogix_dp_device *dp)
> >> if (dp->plat_data->power_on)
> >> dp->plat_data->power_on(dp->plat_data);
> >>
> >> + phy_set_mode(dp->phy, PHY_MODE_DP);
> >> phy_power_on(dp->phy);
> >>
> >> analogix_dp_init_dp(dp);
> >> diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
> >> index 3afc73c858c4..613ce504bea6 100644
> >> --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
> >> +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
> >> @@ -11,6 +11,7 @@
> >> #include <linux/gpio/consumer.h>
> >> #include <linux/io.h>
> >> #include <linux/iopoll.h>
> >> +#include <linux/phy/phy.h>
> >>
> >> #include <drm/bridge/analogix_dp.h>
> >>
> >> @@ -513,10 +514,25 @@ void analogix_dp_enable_sw_function(struct analogix_dp_device *dp)
> >> void analogix_dp_set_link_bandwidth(struct analogix_dp_device *dp, u32 bwtype)
> >> {
> >> u32 reg;
> >> + int ret;
> >>
> >> reg = bwtype;
> >> if ((bwtype == DP_LINK_BW_2_7) || (bwtype == DP_LINK_BW_1_62))
> >> writel(reg, dp->reg_base + ANALOGIX_DP_LINK_BW_SET);
> >> +
> >> + if (dp->phy) {
> >> + union phy_configure_opts phy_cfg = {0};
> >> +
> >> + phy_cfg.dp.lanes = dp->link_train.lane_count;
> >
> > Should not be necessary, you are only setting the .set_rate.
>
> Indeed, this can be dropped.
>
> >
> >> + phy_cfg.dp.link_rate =
> >> + drm_dp_bw_code_to_link_rate(dp->link_train.link_rate) / 100;
> >> + phy_cfg.dp.set_rate = true;
> >> + ret = phy_configure(dp->phy, &phy_cfg);
> >> + if (ret && ret != -EOPNOTSUPP) {
> >> + dev_err(dp->dev, "%s: phy_configure() failed: %d\n", __func__, ret);
> >> + return;
> >> + }
> >> + }
> >> }
> >>
> >> void analogix_dp_get_link_bandwidth(struct analogix_dp_device *dp, u32 *bwtype)
> >> @@ -530,9 +546,22 @@ void analogix_dp_get_link_bandwidth(struct analogix_dp_device *dp, u32 *bwtype)
> >> void analogix_dp_set_lane_count(struct analogix_dp_device *dp, u32 count)
> >> {
> >> u32 reg;
> >> + int ret;
> >>
> >> reg = count;
> >> writel(reg, dp->reg_base + ANALOGIX_DP_LANE_COUNT_SET);
> >> +
> >> + if (dp->phy) {
> >> + union phy_configure_opts phy_cfg = {0};
> >> +
> >> + phy_cfg.dp.lanes = dp->link_train.lane_count;
> >> + phy_cfg.dp.set_lanes = true;
> >> + ret = phy_configure(dp->phy, &phy_cfg);
> >> + if (ret && ret != -EOPNOTSUPP) {
> >> + dev_err(dp->dev, "%s: phy_configure() failed: %d\n", __func__, ret);
> >> + return;
> >> + }
> >> + }
> >> }
> >>
> >> void analogix_dp_get_lane_count(struct analogix_dp_device *dp, u32 *count)
> >> @@ -546,10 +575,37 @@ void analogix_dp_get_lane_count(struct analogix_dp_device *dp, u32 *count)
> >> void analogix_dp_set_lane_link_training(struct analogix_dp_device *dp)
> >> {
> >> u8 lane;
> >> + int ret;
> >>
> >> for (lane = 0; lane < dp->link_train.lane_count; lane++)
> >> writel(dp->link_train.training_lane[lane],
> >> dp->reg_base + ANALOGIX_DP_LN0_LINK_TRAINING_CTL + 4 * lane);
> >> +
> >> + if (dp->phy) {
> >> + union phy_configure_opts phy_cfg = {0};
> >> +
> >> + for (lane = 0; lane < dp->link_train.lane_count; lane++) {
> >> + u8 training_lane = dp->link_train.training_lane[lane];
> >> + u8 vs, pe;
> >> +
> >> + vs = (training_lane & DP_TRAIN_VOLTAGE_SWING_MASK) >>
> >> + DP_TRAIN_VOLTAGE_SWING_SHIFT;
> >> + pe = (training_lane & DP_TRAIN_PRE_EMPHASIS_MASK) >>
> >> + DP_TRAIN_PRE_EMPHASIS_SHIFT;
> >> + phy_cfg.dp.voltage[lane] = vs;
> >> + phy_cfg.dp.pre[lane] = pe;
> >> + }
> >> +
> >> + phy_cfg.dp.lanes = dp->link_train.lane_count;
> >> + phy_cfg.dp.link_rate =
> >> + drm_dp_bw_code_to_link_rate(dp->link_train.link_rate) / 100;
> >
> > This two should not be necessary, please drop them.
>
> These two are necessary for rk_hdptx_phy_set_voltage(), so they cannot
> be dropped.
Please review the documentation for struct phy_configure_opts_dp and
fix your PHY driver to skip the values for which the .set_foo isn't
set. Then you might have to change this part.
You are setting just .set_voltages. It means that the rate and .lanes
shouldn't be changed and can be used as they were set by the previous
calls to phy_configure().
>
> >
> >> + phy_cfg.dp.set_voltages = true;
> >> + ret = phy_configure(dp->phy, &phy_cfg);
> >> + if (ret && ret != -EOPNOTSUPP) {
> >> + dev_err(dp->dev, "%s: phy_configure() failed: %d\n", __func__, ret);
> >> + return;
> >> + }
> >> + }
> >> }
> >>
> >> u32 analogix_dp_get_lane_link_training(struct analogix_dp_device *dp, u8 lane)
> >> --
> >> 2.34.1
> >>
> >
>
> Best regards,
> Damon
>
--
With best wishes
Dmitry
More information about the linux-phy
mailing list