[RESEND PATCH v3 2/2] phy: rockchip-naneng-combo: add rk3576 support
Kever Yang
kever.yang at rock-chips.com
Wed Dec 4 17:17:12 PST 2024
Hi Frank,
On 2024/11/6 10:13, Frank Wang wrote:
> From: Kever Yang <kever.yang at rock-chips.com>
>
> Rockchip RK3576 integrates two naneng-combo PHY, PHY0 is used for
> PCIE and SATA, PHY1 is used for PCIE, SATA and USB3.
>
> This adds device specific data support.
>
> Signed-off-by: Kever Yang <kever.yang at rock-chips.com>
> Signed-off-by: William Wu <william.wu at rock-chips.com>
> Signed-off-by: Frank Wang <frank.wang at rock-chips.com>
Test on rk3576 evb with pcie port.
Test-by: Kever Yang <kever.yang at rock-chips.com>
Thanks,
- Kever
> ---
> Changelog:
> v3:
> - add detail commit contents.
> - using FIELD_PREP() instead of bit shift.
> - leave a blank line after each switch break case.
>
> v2:
> - using constants macro instead of magic values.
> - add more comments for PHY tuning operations.
>
> v1:
> - https://patchwork.kernel.org/project/linux-phy/patch/20241015013351.4884-2-frawang.cn@gmail.com/
>
> .../rockchip/phy-rockchip-naneng-combphy.c | 279 ++++++++++++++++++
> 1 file changed, 279 insertions(+)
>
> diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> index 0a9989e41237f..eceb798567859 100644
> --- a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> +++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> @@ -37,6 +37,10 @@
> #define PHYREG8 0x1C
> #define PHYREG8_SSC_EN BIT(4)
>
> +#define PHYREG10 0x24
> +#define PHYREG10_SSC_PCM_MASK GENMASK(3, 0)
> +#define PHYREG10_SSC_PCM_3500PPM 7
> +
> #define PHYREG11 0x28
> #define PHYREG11_SU_TRIM_0_7 0xF0
>
> @@ -61,17 +65,26 @@
> #define PHYREG16 0x3C
> #define PHYREG16_SSC_CNT_VALUE 0x5f
>
> +#define PHYREG17 0x40
> +
> #define PHYREG18 0x44
> #define PHYREG18_PLL_LOOP 0x32
>
> +#define PHYREG21 0x50
> +#define PHYREG21_RX_SQUELCH_VAL 0x0D
> +
> #define PHYREG27 0x6C
> #define PHYREG27_RX_TRIM_RK3588 0x4C
>
> +#define PHYREG30 0x74
> +
> #define PHYREG32 0x7C
> #define PHYREG32_SSC_MASK GENMASK(7, 4)
> +#define PHYREG32_SSC_DIR_MASK GENMASK(5, 4)
> #define PHYREG32_SSC_DIR_SHIFT 4
> #define PHYREG32_SSC_UPWARD 0
> #define PHYREG32_SSC_DOWNWARD 1
> +#define PHYREG32_SSC_OFFSET_MASK GENMASK(7, 6)
> #define PHYREG32_SSC_OFFSET_SHIFT 6
> #define PHYREG32_SSC_OFFSET_500PPM 1
>
> @@ -79,6 +92,7 @@
> #define PHYREG33_PLL_KVCO_MASK GENMASK(4, 2)
> #define PHYREG33_PLL_KVCO_SHIFT 2
> #define PHYREG33_PLL_KVCO_VALUE 2
> +#define PHYREG33_PLL_KVCO_VALUE_RK3576 4
>
> struct rockchip_combphy_priv;
>
> @@ -98,6 +112,7 @@ struct rockchip_combphy_grfcfg {
> struct combphy_reg pipe_rxterm_set;
> struct combphy_reg pipe_txelec_set;
> struct combphy_reg pipe_txcomp_set;
> + struct combphy_reg pipe_clk_24m;
> struct combphy_reg pipe_clk_25m;
> struct combphy_reg pipe_clk_100m;
> struct combphy_reg pipe_phymode_sel;
> @@ -584,6 +599,266 @@ static const struct rockchip_combphy_cfg rk3568_combphy_cfgs = {
> .combphy_cfg = rk3568_combphy_cfg,
> };
>
> +static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
> +{
> + const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> + unsigned long rate;
> + u32 val;
> +
> + switch (priv->type) {
> + case PHY_TYPE_PCIE:
> + /* Set SSC downward spread spectrum */
> + val = FIELD_PREP(PHYREG32_SSC_MASK, PHYREG32_SSC_DOWNWARD);
> + rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
> +
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
> + break;
> +
> + case PHY_TYPE_USB3:
> + /* Set SSC downward spread spectrum */
> + val = FIELD_PREP(PHYREG32_SSC_MASK, PHYREG32_SSC_DOWNWARD);
> + rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
> +
> + /* Enable adaptive CTLE for USB3.0 Rx */
> + val = readl(priv->mmio + PHYREG15);
> + val |= PHYREG15_CTLE_EN;
> + writel(val, priv->mmio + PHYREG15);
> +
> + /* Set PLL KVCO fine tuning signals */
> + rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK, BIT(3), PHYREG33);
> +
> + /* Set PLL LPF R1 to su_trim[10:7]=1001 */
> + writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
> +
> + /* Set PLL input clock divider 1/2 */
> + val = FIELD_PREP(PHYREG6_PLL_DIV_MASK, PHYREG6_PLL_DIV_2);
> + rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK, val, PHYREG6);
> +
> + /* Set PLL loop divider */
> + writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
> +
> + /* Set PLL KVCO to min and set PLL charge pump current to max */
> + writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
> +
> + /* Set Rx squelch input filler bandwidth */
> + writel(PHYREG21_RX_SQUELCH_VAL, priv->mmio + PHYREG21);
> +
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->usb_mode_set, true);
> + break;
> +
> + case PHY_TYPE_SATA:
> + /* Enable adaptive CTLE for SATA Rx */
> + val = readl(priv->mmio + PHYREG15);
> + val |= PHYREG15_CTLE_EN;
> + writel(val, priv->mmio + PHYREG15);
> +
> + /* Set tx_rterm = 50 ohm and rx_rterm = 43.5 ohm */
> + val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT;
> + val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT;
> + writel(val, priv->mmio + PHYREG7);
> +
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_sata, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_sata, true);
> + rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con0_for_sata, true);
> + rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con1_for_sata, true);
> + break;
> +
> + default:
> + dev_err(priv->dev, "incompatible PHY type\n");
> + return -EINVAL;
> + }
> +
> + rate = clk_get_rate(priv->refclk);
> +
> + switch (rate) {
> + case REF_CLOCK_24MHz:
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_24m, true);
> + if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) {
> + /* Set ssc_cnt[9:0]=0101111101 & 31.5KHz */
> + val = FIELD_PREP(PHYREG15_SSC_CNT_MASK, PHYREG15_SSC_CNT_VALUE);
> + rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
> + val, PHYREG15);
> +
> + writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
> + } else if (priv->type == PHY_TYPE_PCIE) {
> + /* PLL KVCO tuning fine */
> + val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
> + rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
> + val, PHYREG33);
> +
> + /* Set up rx_pck invert and rx msb to disable */
> + writel(0x00, priv->mmio + PHYREG27);
> +
> + /*
> + * Set up SU adjust signal:
> + * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
> + * su_trim[15:8], PLL LPF R1 adujst bits[9:7]=3'b011
> + * su_trim[31:24], CKDRV adjust
> + */
> + writel(0x90, priv->mmio + PHYREG11);
> + writel(0x02, priv->mmio + PHYREG12);
> + writel(0x57, priv->mmio + PHYREG14);
> +
> + writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
> + }
> + break;
> +
> + case REF_CLOCK_25MHz:
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_25m, true);
> + break;
> +
> + case REF_CLOCK_100MHz:
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
> + if (priv->type == PHY_TYPE_PCIE) {
> + /* gate_tx_pck_sel length select work for L1SS */
> + writel(0xc0, priv->mmio + PHYREG30);
> +
> + /* PLL KVCO tuning fine */
> + val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
> + rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
> + val, PHYREG33);
> +
> + /* Set up rx_trim: PLL LPF C1 85pf R1 1.25kohm */
> + writel(0x4c, priv->mmio + PHYREG27);
> +
> + /*
> + * Set up SU adjust signal:
> + * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
> + * su_trim[15:8], bypass PLL loop divider code, and
> + * PLL LPF R1 adujst bits[9:7]=3'b101
> + * su_trim[23:16], CKRCV adjust
> + * su_trim[31:24], CKDRV adjust
> + */
> + writel(0x90, priv->mmio + PHYREG11);
> + writel(0x43, priv->mmio + PHYREG12);
> + writel(0x88, priv->mmio + PHYREG13);
> + writel(0x56, priv->mmio + PHYREG14);
> + } else if (priv->type == PHY_TYPE_SATA) {
> + /* downward spread spectrum +500ppm */
> + val = FIELD_PREP(PHYREG32_SSC_DIR_MASK, PHYREG32_SSC_DOWNWARD);
> + val |= FIELD_PREP(PHYREG32_SSC_OFFSET_MASK, PHYREG32_SSC_OFFSET_500PPM);
> + rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
> +
> + /* ssc ppm adjust to 3500ppm */
> + rockchip_combphy_updatel(priv, PHYREG10_SSC_PCM_MASK,
> + PHYREG10_SSC_PCM_3500PPM,
> + PHYREG10);
> + }
> + break;
> +
> + default:
> + dev_err(priv->dev, "Unsupported rate: %lu\n", rate);
> + return -EINVAL;
> + }
> +
> + if (priv->ext_refclk) {
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
> + if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
> + val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
> + rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
> + val, PHYREG33);
> +
> + /* Set up rx_trim: PLL LPF C1 85pf R1 2.5kohm */
> + writel(0x0c, priv->mmio + PHYREG27);
> +
> + /*
> + * Set up SU adjust signal:
> + * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
> + * su_trim[15:8], bypass PLL loop divider code, and
> + * PLL LPF R1 adujst bits[9:7]=3'b101.
> + * su_trim[23:16], CKRCV adjust
> + * su_trim[31:24], CKDRV adjust
> + */
> + writel(0x90, priv->mmio + PHYREG11);
> + writel(0x43, priv->mmio + PHYREG12);
> + writel(0x88, priv->mmio + PHYREG13);
> + writel(0x56, priv->mmio + PHYREG14);
> + }
> + }
> +
> + if (priv->enable_ssc) {
> + val = readl(priv->mmio + PHYREG8);
> + val |= PHYREG8_SSC_EN;
> + writel(val, priv->mmio + PHYREG8);
> +
> + if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_24MHz) {
> + /* Set PLL loop divider */
> + writel(0x00, priv->mmio + PHYREG17);
> + writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
> +
> + /* Set up rx_pck invert and rx msb to disable */
> + writel(0x00, priv->mmio + PHYREG27);
> +
> + /*
> + * Set up SU adjust signal:
> + * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
> + * su_trim[15:8], PLL LPF R1 adujst bits[9:7]=3'b101
> + * su_trim[23:16], CKRCV adjust
> + * su_trim[31:24], CKDRV adjust
> + */
> + writel(0x90, priv->mmio + PHYREG11);
> + writel(0x02, priv->mmio + PHYREG12);
> + writel(0x08, priv->mmio + PHYREG13);
> + writel(0x57, priv->mmio + PHYREG14);
> + writel(0x40, priv->mmio + PHYREG15);
> +
> + writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
> +
> + val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
> + writel(val, priv->mmio + PHYREG33);
> + }
> + }
> +
> + return 0;
> +}
> +
> +static const struct rockchip_combphy_grfcfg rk3576_combphy_grfcfgs = {
> + /* pipe-phy-grf */
> + .pcie_mode_set = { 0x0000, 5, 0, 0x00, 0x11 },
> + .usb_mode_set = { 0x0000, 5, 0, 0x00, 0x04 },
> + .pipe_rxterm_set = { 0x0000, 12, 12, 0x00, 0x01 },
> + .pipe_txelec_set = { 0x0004, 1, 1, 0x00, 0x01 },
> + .pipe_txcomp_set = { 0x0004, 4, 4, 0x00, 0x01 },
> + .pipe_clk_24m = { 0x0004, 14, 13, 0x00, 0x00 },
> + .pipe_clk_25m = { 0x0004, 14, 13, 0x00, 0x01 },
> + .pipe_clk_100m = { 0x0004, 14, 13, 0x00, 0x02 },
> + .pipe_phymode_sel = { 0x0008, 1, 1, 0x00, 0x01 },
> + .pipe_rate_sel = { 0x0008, 2, 2, 0x00, 0x01 },
> + .pipe_rxterm_sel = { 0x0008, 8, 8, 0x00, 0x01 },
> + .pipe_txelec_sel = { 0x0008, 12, 12, 0x00, 0x01 },
> + .pipe_txcomp_sel = { 0x0008, 15, 15, 0x00, 0x01 },
> + .pipe_clk_ext = { 0x000c, 9, 8, 0x02, 0x01 },
> + .pipe_phy_status = { 0x0034, 6, 6, 0x01, 0x00 },
> + .con0_for_pcie = { 0x0000, 15, 0, 0x00, 0x1000 },
> + .con1_for_pcie = { 0x0004, 15, 0, 0x00, 0x0000 },
> + .con2_for_pcie = { 0x0008, 15, 0, 0x00, 0x0101 },
> + .con3_for_pcie = { 0x000c, 15, 0, 0x00, 0x0200 },
> + .con0_for_sata = { 0x0000, 15, 0, 0x00, 0x0129 },
> + .con1_for_sata = { 0x0004, 15, 0, 0x00, 0x0000 },
> + .con2_for_sata = { 0x0008, 15, 0, 0x00, 0x80c1 },
> + .con3_for_sata = { 0x000c, 15, 0, 0x00, 0x0407 },
> + /* php-grf */
> + .pipe_con0_for_sata = { 0x001C, 2, 0, 0x00, 0x2 },
> + .pipe_con1_for_sata = { 0x0020, 2, 0, 0x00, 0x2 },
> +};
> +
> +static const struct rockchip_combphy_cfg rk3576_combphy_cfgs = {
> + .num_phys = 2,
> + .phy_ids = {
> + 0x2b050000,
> + 0x2b060000
> + },
> + .grfcfg = &rk3576_combphy_grfcfgs,
> + .combphy_cfg = rk3576_combphy_cfg,
> +};
> +
> static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
> {
> const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> @@ -775,6 +1050,10 @@ static const struct of_device_id rockchip_combphy_of_match[] = {
> .compatible = "rockchip,rk3568-naneng-combphy",
> .data = &rk3568_combphy_cfgs,
> },
> + {
> + .compatible = "rockchip,rk3576-naneng-combphy",
> + .data = &rk3576_combphy_cfgs,
> + },
> {
> .compatible = "rockchip,rk3588-naneng-combphy",
> .data = &rk3588_combphy_cfgs,
More information about the linux-phy
mailing list