[PATCH v2 1/2] dt-bindings: phy: Add Sophgo CV1800 USB phy

[Inochi Amaoto]

On Tue, Apr 30, 2024 at 06:09:20PM GMT, Conor Dooley wrote:
> On Mon, Apr 29, 2024 at 08:31:11AM +0800, Inochi Amaoto wrote:
> > The USB phy of Sophgo CV18XX series SoC needs to sense a pin called
> > "VBUS_DET" to get the right operation mode. If this pin is not
> > connected, it only supports setting the mode manually.
> > 
> > Add USB phy bindings for Sophgo CV18XX/SG200X series SoC.
> > 
> > Signed-off-by: Inochi Amaoto <inochiama at outlook.com>
> > ---
> >  .../bindings/phy/sophgo,cv1800-usb-phy.yaml   | 68 +++++++++++++++++++
> >  1 file changed, 68 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/phy/sophgo,cv1800-usb-phy.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/phy/sophgo,cv1800-usb-phy.yaml b/Documentation/devicetree/bindings/phy/sophgo,cv1800-usb-phy.yaml
> > new file mode 100644
> > index 000000000000..7e3382c18d44
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/phy/sophgo,cv1800-usb-phy.yaml
> > @@ -0,0 +1,68 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/phy/sophgo,cv1800-usb-phy.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Sophgo CV18XX/SG200X USB 2.0 PHY
> > +
> > +maintainers:
> > +  - Inochi Amaoto <inochiama at outlook.com>
> > +
> > +properties:
> > +  compatible:
> > +    const: sophgo,cv1800-usb-phy
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  "#phy-cells":
> > +    const: 0
> > +
> > +  clocks:
> > +    items:
> > +      - description: PHY clock
> > +      - description: PHY app clock
> > +      - description: PHY stb clock
> > +      - description: PHY lpm clock
> > +
> > +  clock-names:
> > +    items:
> > +      - const: phy
> > +      - const: app
> > +      - const: stb
> > +      - const: lpm
> > +
> > +  vbus_det-gpios:
> 
> "vbus_det-gpios" isn't a common property AFAICT, why does it not get a
> vendor prefix when the other gpios property does?
> 

I have seen other binding (such as sunxi phy) uses this property without 
vendor prefix. So I think it is a common property and don't add perfix 
for it. But it is OK for me add the vendor prefix, thanks.

> > +    description: GPIO to the USB OTG VBUS detect pin. This should not be
> > +      defined if vbus_det pin and switch pin are connected, which may
> > +      break the VBUS detection.
> > +    maxItems: 1
> > +
> > +  sophgo,switch-gpios:
> > +    description: GPIO array for the phy to control connected switch. For
> > +      host mode, the driver will set these GPIOs to low one by one. For
> > +      device mode, the driver will set these GPIOs to high in reverse
> > +      order.
> > +    maxItems: 2
> 
> You're still missing the itemised description of what each of the gpios
> here are - how would I know which order to put the GPIOs in?
> 
> Cheers,
> Conor.

In most case, the order depends on hardware design. But following the
guide sophgo provides, it does have an common order. Is it good to add
this description as a reference guide? If so, I will add it.

Regards,
Inochi

> 
> > +
> > +required:
> > +  - compatible
> > +  - "#phy-cells"
> > +  - clocks
> > +  - clock-names
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > +  - |
> > +    phy at 48 {
> > +      compatible = "sophgo,cv1800-usb-phy";
> > +      reg = <0x48 0x4>;
> > +      #phy-cells = <0>;
> > +      clocks = <&clk 92>, <&clk 93>,
> > +               <&clk 94>, <&clk 95>;
> > +      clock-names = "phy", "app", "stb", "lpm";
> > +    };
> > +
> > +...
> > --
> > 2.44.0
> >