[PATCH 5/7] arm64: dts: qcom: sc7180: Add UFS nodes

[Konrad Dybcio]

On 10/7/23 15:58, David Wronek wrote:
> Add the UFS and QMP PHY nodes for the Qualcomm SC7180 SoC.
> 
> Signed-off-by: David Wronek <davidwronek at gmail.com>
> ---
>   arch/arm64/boot/dts/qcom/sc7180.dtsi | 70 ++++++++++++++++++++++++++++
>   1 file changed, 70 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 11f353d416b4..9f18be4fd61a 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -1532,6 +1532,76 @@ mmss_noc: interconnect at 1740000 {
>   			qcom,bcm-voters = <&apps_bcm_voter>;
>   		};
>   
> +		ufs_mem_hc: ufshc at 1d84000 {
> +			compatible = "qcom,sc7180-ufshc", "qcom,ufshc",
> +				     "jedec,ufs-2.0";
> +			reg = <0 0x01d84000 0 0x3000>,
> +			      <0 0x01d90000 0 0x8000>;
> +			reg-names = "std", "ice";
Recently the ICE was separated into its own node

> +			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
> +			phys = <&ufs_mem_phy>;
> +			phy-names = "ufsphy";
> +			lanes-per-direction = <1>;
> +			power-domains = <&gcc UFS_PHY_GDSC>;
> +			#reset-cells = <1>;
> +			resets = <&gcc GCC_UFS_PHY_BCR>;
> +			reset-names = "rst";
> +
> +			iommus = <&apps_smmu 0xa0 0x0>;
> +
> +			clock-names =
> +				"core_clk",
Remove the newline after the =, here and below

> +				"bus_aggr_clk",
> +				"iface_clk",
> +				"core_clk_unipro",
> +				"ref_clk",
> +				"tx_lane0_sync_clk",
> +				"rx_lane0_sync_clk",
> +				"ice_core_clk";
> +			clocks =
> +				<&gcc GCC_UFS_PHY_AXI_CLK>,
> +				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
> +				<&gcc GCC_UFS_PHY_AHB_CLK>,
> +				<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
> +				<&rpmhcc RPMH_CXO_CLK>,
> +				<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
> +				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
> +				<&gcc GCC_UFS_PHY_ICE_CORE_CLK>;
> +			freq-table-hz =
> +				<50000000 200000000>,
> +				<0 0>,
> +				<0 0>,
> +				<37500000 150000000>,
> +				<0 0>,
> +				<0 0>,
> +				<0 0>,
> +				<0 300000000>;
> +
> +			interconnects = <&aggre1_noc MASTER_UFS_MEM 0 &mc_virt SLAVE_EBI1 0>,
> +				<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_MEM_CFG 0>;
Please make the <s align and use QCOM_ICC_TAG_ALWAYS from 
include/dt-bindings/interconnect/qcom,icc.h like in sa8775p.dtsi
> +			interconnect-names = "ufs-ddr", "cpu-ufs";
> +
> +			status = "disabled";
> +		};
> +
> +		ufs_mem_phy: phy at 1d87000 {
> +			compatible = "qcom,sc7180-qmp-ufs-phy";
> +			reg = <0 0x01d87000 0 0x1000>;
> +
> +			clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
> +				<&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
Please align the <s

Konrad