[PATCH 5/6] arm64: dts: qcom: ipq5018: Add PCIe related nodes
Dmitry Baryshkov
dmitry.baryshkov at linaro.org
Tue Oct 3 08:23:00 PDT 2023
On Tue, 3 Oct 2023 at 15:10, Nitheesh Sekar <quic_nsekar at quicinc.com> wrote:
>
> Add phy and controller nodes for PCIe_x2 and PCIe_x1.
> PCIe_x2 is 2-lane Gen2 and PCIe_x1 is 1-lane Gen2.
>
> Signed-off-by: Nitheesh Sekar <quic_nsekar at quicinc.com>
> ---
> arch/arm64/boot/dts/qcom/ipq5018.dtsi | 186 +++++++++++++++++++++++++-
> 1 file changed, 184 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> index 38ffdc3cbdcd..0818fdd1e693 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> @@ -8,6 +8,7 @@
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
> #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
> +#include <dt-bindings/gpio/gpio.h>
>
> / {
> interrupt-parent = <&intc>;
> @@ -94,6 +95,38 @@
> #size-cells = <1>;
> ranges = <0 0 0 0xffffffff>;
>
> + pcie_x1phy: phy at 7e000{
> + compatible = "qcom,ipq5018-uniphy-pcie-gen2x1";
> + reg = <0x0007e000 0x800>;
> + #phy-cells = <0>;
> + #clock-cells = <0>;
> + clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
> + clock-names = "pipe_clk";
> + clock-output-names = "pcie1_pipe_clk";
> + assigned-clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
> + assigned-clock-rates = <125000000>;
> + resets = <&gcc GCC_PCIE1_PHY_BCR>,
> + <&gcc GCC_PCIE1PHY_PHY_BCR>;
> + reset-names = "phy", "phy_phy";
> + status = "disabled";
> + };
> +
> + pcie_x2phy: phy at 86000{
> + compatible = "qcom,ipq5018-uniphy-pcie-gen2x2";
> + reg = <0x00086000 0x800>;
> + #phy-cells = <0>;
> + #clock-cells = <0>;
> + clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
> + clock-names = "pipe_clk";
> + clock-output-names = "pcie0_pipe_clk";
> + assigned-clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
> + assigned-clock-rates = <125000000>;
Can this go into the PHY driver?
> + resets = <&gcc GCC_PCIE0_PHY_BCR>,
> + <&gcc GCC_PCIE0PHY_PHY_BCR>;
> + reset-names = "phy", "phy_phy";
> + status = "disabled";
> + };
> +
> tlmm: pinctrl at 1000000 {
> compatible = "qcom,ipq5018-tlmm";
> reg = <0x01000000 0x300000>;
> @@ -117,8 +150,8 @@
> reg = <0x01800000 0x80000>;
> clocks = <&xo_board_clk>,
> <&sleep_clk>,
> - <0>,
> - <0>,
> + <&pcie_x2phy>,
> + <&pcie_x1phy>,
> <0>,
> <0>,
> <0>,
> @@ -246,6 +279,155 @@
> status = "disabled";
> };
> };
> +
> + pcie_x1: pci at 80000000 {
> + compatible = "qcom,pcie-ipq5018";
> + reg = <0x80000000 0xf1d
Each address/size tuple should be a separate <> entry.
> + 0x80000F20 0xa8
lowercase
> + 0x80001000 0x1000
> + 0x78000 0x3000
Would you notice why this line stands away from the rest of entries here?
> + 0x80100000 0x1000>;
> + reg-names = "dbi", "elbi", "atu", "parf", "config";
> + device_type = "pci";
> + linux,pci-domain = <0>;
> + bus-range = <0x00 0xff>;
> + num-lanes = <1>;
> + max-link-speed = <2>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + phys = <&pcie_x1phy>;
> + phy-names ="pciephy";
> +
> + ranges = <0x81000000 0 0x80200000 0x80200000
> + 0 0x00100000 /* downstream I/O */
> + 0x82000000 0 0x80300000 0x80300000
> + 0 0x10000000>; /* non-prefetchable memory */
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 142
> + IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> + <0 0 0 2 &intc 0 143
> + IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> + <0 0 0 3 &intc 0 144
> + IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> + <0 0 0 4 &intc 0 145
> + IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
> + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "global_irq";
> +
> + clocks = <&gcc GCC_SYS_NOC_PCIE1_AXI_CLK>,
> + <&gcc GCC_PCIE1_AXI_M_CLK>,
> + <&gcc GCC_PCIE1_AXI_S_CLK>,
> + <&gcc GCC_PCIE1_AHB_CLK>,
> + <&gcc GCC_PCIE1_AUX_CLK>,
> + <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>;
> +
> + clock-names = "iface",
> + "axi_m",
> + "axi_s",
> + "ahb",
> + "aux",
> + "axi_bridge";
> +
> + resets = <&gcc GCC_PCIE1_PIPE_ARES>,
> + <&gcc GCC_PCIE1_SLEEP_ARES>,
> + <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
> + <&gcc GCC_PCIE1_AXI_MASTER_ARES>,
> + <&gcc GCC_PCIE1_AXI_SLAVE_ARES>,
> + <&gcc GCC_PCIE1_AHB_ARES>,
> + <&gcc GCC_PCIE1_AXI_MASTER_STICKY_ARES>,
> + <&gcc GCC_PCIE1_AXI_SLAVE_STICKY_ARES>;
> +
> + reset-names = "pipe",
> + "sleep",
> + "sticky",
> + "axi_m",
> + "axi_s",
> + "ahb",
> + "axi_m_sticky",
> + "axi_s_sticky";
> +
> + msi-map = <0x0 &v2m0 0x0 0xff8>;
> + status = "disabled";
> + };
> +
> + pcie_x2: pci at a0000000 {
> + compatible = "qcom,pcie-ipq5018";
> + reg = <0xa0000000 0xf1d
> + 0xa0000F20 0xa8
> + 0xa0001000 0x1000
> + 0x80000 0x3000
> + 0xa0100000 0x1000>;
> + reg-names = "dbi", "elbi", "atu", "parf", "config";
> + device_type = "pci";
> + linux,pci-domain = <1>;
> + bus-range = <0x00 0xff>;
> + num-lanes = <2>;
> + max-link-speed = <2>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + phys = <&pcie_x2phy>;
> + phy-names ="pciephy";
> +
> + ranges = <0x81000000 0 0xa0200000 0xa0200000
> + 0 0x00100000 /* downstream I/O */
> + 0x82000000 0 0xa0300000 0xa0300000
> + 0 0x10000000>; /* non-prefetchable memory */
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 75
> + IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> + <0 0 0 2 &intc 0 78
> + IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> + <0 0 0 3 &intc 0 79
> + IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> + <0 0 0 4 &intc 0 83
> + IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
> + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "global_irq";
> +
> + clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
> + <&gcc GCC_PCIE0_AXI_M_CLK>,
> + <&gcc GCC_PCIE0_AXI_S_CLK>,
> + <&gcc GCC_PCIE0_AHB_CLK>,
> + <&gcc GCC_PCIE0_AUX_CLK>,
> + <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>;
> +
> + clock-names = "iface",
> + "axi_m",
> + "axi_s",
> + "ahb",
> + "aux",
> + "axi_bridge";
> +
> + resets = <&gcc GCC_PCIE0_PIPE_ARES>,
> + <&gcc GCC_PCIE0_SLEEP_ARES>,
> + <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
> + <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
> + <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
> + <&gcc GCC_PCIE0_AHB_ARES>,
> + <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>,
> + <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>;
> +
> + reset-names = "pipe",
> + "sleep",
> + "sticky",
> + "axi_m",
> + "axi_s",
> + "ahb",
> + "axi_m_sticky",
> + "axi_s_sticky";
> +
> + msi-map = <0x0 &v2m0 0x0 0xff8>;
> + status = "disabled";
> + };
> +
> };
>
> timer {
> --
> 2.17.1
>
--
With best wishes
Dmitry
More information about the linux-phy
mailing list