[PATCH v6 08/10] phy: qualcomm: phy-qcom-qmp-ufs: Add High Speed Gear 5 support for SM8550
Can Guo
quic_cang at quicinc.com
Thu Nov 30 00:49:12 PST 2023
On 11/30/2023 4:38 PM, Manivannan Sadhasivam wrote:
> On Thu, Nov 30, 2023 at 04:14:25PM +0800, Can Guo wrote:
>>
>>
>> On 11/30/2023 3:12 PM, Manivannan Sadhasivam wrote:
>>> On Wed, Nov 29, 2023 at 12:28:33AM -0800, Can Guo wrote:
>>>> On SM8550, two sets of UFS PHY settings are provided, one set is to support
>>>> HS-G5, another set is to support HS-G4 and lower gears. The two sets of PHY
>>>> settings are programming different values to different registers, mixing
>>>> the two sets and/or overwriting one set with another set is definitely not
>>>> blessed by UFS PHY designers.
>>>>
>>>> To add HS-G5 support for SM8550, split the two sets of PHY settings into
>>>> their dedicated overlay tables, only the common parts of the two sets of
>>>> PHY settings are left in the .tbls.
>>>>
>>>> Consider we are going to add even higher gear support in future, to avoid
>>>> adding more tables with different names, rename the .tbls_hs_g4 and make it
>>>> an array, a size of 2 is enough as of now.
>>>>
>>>> In this case, .tbls alone is not a complete set of PHY settings, so either
>>>> tbls_hs_overlay[0] or tbls_hs_overlay[1] must be applied on top of the
>>>> .tbls to become a complete set of PHY settings.
>>>>
>>>> Signed-off-by: Can Guo <quic_cang at quicinc.com>
>>>> ---
>>>> drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h | 2 +
>>>> drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h | 2 +
>>>> .../qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h | 9 ++
>>>> drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 170 ++++++++++++++++++---
>>>> 4 files changed, 163 insertions(+), 20 deletions(-)
>>>>
>>>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h
>>>> index c23d5e4..e563af5 100644
>>>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h
>>>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h
>>>> @@ -18,6 +18,7 @@
>>>> #define QPHY_V6_PCS_UFS_BIST_FIXED_PAT_CTRL 0x060
>>>> #define QPHY_V6_PCS_UFS_TX_HSGEAR_CAPABILITY 0x074
>>>> #define QPHY_V6_PCS_UFS_RX_HSGEAR_CAPABILITY 0x0bc
>>>> +#define QPHY_V6_PCS_UFS_RX_HS_G5_SYNC_LENGTH_CAPABILITY 0x12c
>>>> #define QPHY_V6_PCS_UFS_DEBUG_BUS_CLKSEL 0x158
>>>> #define QPHY_V6_PCS_UFS_LINECFG_DISABLE 0x17c
>>>> #define QPHY_V6_PCS_UFS_RX_MIN_HIBERN8_TIME 0x184
>>>> @@ -27,5 +28,6 @@
>>>> #define QPHY_V6_PCS_UFS_READY_STATUS 0x1a8
>>>> #define QPHY_V6_PCS_UFS_TX_MID_TERM_CTRL1 0x1f4
>>>> #define QPHY_V6_PCS_UFS_MULTI_LANE_CTRL1 0x1fc
>>>> +#define QPHY_V6_PCS_UFS_RX_HSG5_SYNC_WAIT_TIME 0x220
>>>> #endif
>>>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h
>>>> index f420f8f..ef392ce 100644
>>>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h
>>>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h
>>>> @@ -56,6 +56,8 @@
>>>> #define QSERDES_V6_COM_SYS_CLK_CTRL 0xe4
>>>> #define QSERDES_V6_COM_SYSCLK_BUF_ENABLE 0xe8
>>>> #define QSERDES_V6_COM_PLL_IVCO 0xf4
>>>> +#define QSERDES_V6_COM_CMN_IETRIM 0xfc
>>>> +#define QSERDES_V6_COM_CMN_IPTRIM 0x100
>>>> #define QSERDES_V6_COM_SYSCLK_EN_SEL 0x110
>>>> #define QSERDES_V6_COM_RESETSM_CNTRL 0x118
>>>> #define QSERDES_V6_COM_LOCK_CMP_EN 0x120
>>>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
>>>> index 674f158..48f31c8 100644
>>>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
>>>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
>>>> @@ -15,8 +15,15 @@
>>>> #define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE2 0x08
>>>> #define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4 0x10
>>>> +#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_SO_GAIN_RATE4 0x24
>>>> +#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_COUNT_HIGH_RATE4 0x54
>>>> #define QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE2 0xd4
>>>> +#define QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE4 0xdc
>>>> +#define QSERDES_UFS_V6_RX_UCDR_SO_GAIN_RATE4 0xf0
>>>> +#define QSERDES_UFS_V6_RX_UCDR_PI_CONTROLS 0xf4
>>>> #define QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL 0x178
>>>> +#define QSERDES_UFS_V6_RX_EQ_OFFSET_ADAPTOR_CNTRL1 0x1bc
>>>> +#define QSERDES_UFS_V6_RX_OFFSET_ADAPTOR_CNTRL3 0x1c4
>>>> #define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0 0x208
>>>> #define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B1 0x20c
>>>> #define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B3 0x214
>>>> @@ -28,6 +35,8 @@
>>>> #define QSERDES_UFS_V6_RX_MODE_RATE3_B5 0x264
>>>> #define QSERDES_UFS_V6_RX_MODE_RATE3_B8 0x270
>>>> #define QSERDES_UFS_V6_RX_MODE_RATE4_B3 0x280
>>>> +#define QSERDES_UFS_V6_RX_MODE_RATE4_B4 0x284
>>>> #define QSERDES_UFS_V6_RX_MODE_RATE4_B6 0x28c
>>>> +#define QSERDES_UFS_V6_RX_DLL0_FTUNE_CTRL 0x2f8
>>>> #endif
>>>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>>>> index 2173418..7e5f1154 100644
>>>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>>>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>>>> @@ -41,6 +41,8 @@
>>>> #define PHY_INIT_COMPLETE_TIMEOUT 10000
>>>> +#define NUM_OVERLAY 2
>>>> +
>>>> struct qmp_phy_init_tbl {
>>>> unsigned int offset;
>>>> unsigned int val;
>>>> @@ -754,15 +756,22 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_serdes[] = {
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x11),
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00),
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x01),
>>>> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x04),
>>>> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f),
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_INITVAL2, 0x00),
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
>>>> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x7f),
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x06),
>>>> +};
>>>> +
>>>> +static const struct qmp_phy_init_tbl sm8550_ufsphy_hs_b_serdes[] = {
>>>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x44),
>>>> +};
>>>> +
>>>> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_serdes[] = {
>>>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x04),
>>>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f),
>>>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x4c),
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x0a),
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x18),
>>>> @@ -771,19 +780,24 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_serdes[] = {
>>>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x07),
>>>> };
>>>> -static const struct qmp_phy_init_tbl sm8550_ufsphy_hs_b_serdes[] = {
>>>> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x44),
>>>> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g5_serdes[] = {
>>>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x1f),
>>>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_IETRIM, 0x1b),
>>>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_IPTRIM, 0x1c),
>>>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x06),
>>>> };
>>>> static const struct qmp_phy_init_tbl sm8550_ufsphy_tx[] = {
>>>> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_LANE_MODE_1, 0x05),
>>>> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_TX, 0x07),
>>>> +};
>>>> +
>>>> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_tx[] = {
>>>> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_FR_DCC_CTRL, 0x4c),
>>>> };
>>>> static const struct qmp_phy_init_tbl sm8550_ufsphy_rx[] = {
>>>> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE2, 0x0c),
>>>> - QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x0e),
>>>> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0, 0xc2),
>>>> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B1, 0xc2),
>>>> @@ -799,16 +813,45 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_rx[] = {
>>>> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE3_B8, 0x02),
>>>> };
>>>> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_rx[] = {
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x0e),
>>>> +};
>>>> +
>>>> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g5_rx[] = {
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE4, 0x0c),
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_SO_GAIN_RATE4, 0x04),
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x14),
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_PI_CONTROLS, 0x07),
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_OFFSET_ADAPTOR_CNTRL3, 0x0e),
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_COUNT_HIGH_RATE4, 0x02),
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4, 0x1c),
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_SO_GAIN_RATE4, 0x06),
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x08),
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE4_B3, 0xb9),
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE4_B4, 0x4f),
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE4_B6, 0xff),
>>>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_DLL0_FTUNE_CTRL, 0x30),
>>>> +};
>>>> +
>>>> static const struct qmp_phy_init_tbl sm8550_ufsphy_pcs[] = {
>>>> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_SIGDET_CTRL2, 0x69),
>>>> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_LARGE_AMP_DRV_LVL, 0x0f),
>>>> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
>>>> - QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x2b),
>>>> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
>>>> +};
>>>> +
>>>> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_pcs[] = {
>>>> + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x2b),
>>>> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x04),
>>>> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x04),
>>>> };
>>>> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g5_pcs[] = {
>>>> + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x33),
>>>> + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_HS_G5_SYNC_LENGTH_CAPABILITY, 0x4f),
>>>> + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_HSG5_SYNC_WAIT_TIME, 0x9e),
>>>> +};
>>>> +
>>>> struct qmp_ufs_offsets {
>>>> u16 serdes;
>>>> u16 pcs;
>>>> @@ -828,6 +871,8 @@ struct qmp_phy_cfg_tbls {
>>>> int rx_num;
>>>> const struct qmp_phy_init_tbl *pcs;
>>>> int pcs_num;
>>>> + /* Maximum supported Gear of this tbls */
>>>> + u32 max_gear;
>>>> };
>>>> /* struct qmp_phy_cfg - per-PHY initialization config */
>>>> @@ -835,13 +880,15 @@ struct qmp_phy_cfg {
>>>> int lanes;
>>>> const struct qmp_ufs_offsets *offsets;
>>>> + /* Maximum supported Gear of this config */
>>>> + u32 max_supported_gear;
>>>> /* Main init sequence for PHY blocks - serdes, tx, rx, pcs */
>>>> const struct qmp_phy_cfg_tbls tbls;
>>>> /* Additional sequence for HS Series B */
>>>> const struct qmp_phy_cfg_tbls tbls_hs_b;
>>>> - /* Additional sequence for HS G4 */
>>>> - const struct qmp_phy_cfg_tbls tbls_hs_g4;
>>>> + /* Additional sequence for different HS Gears */
>>>> + const struct qmp_phy_cfg_tbls tbls_hs_overlay[NUM_OVERLAY];
>>>> /* clock ids to be requested */
>>>> const char * const *clk_list;
>>>> @@ -944,6 +991,7 @@ static const struct qmp_phy_cfg msm8996_ufsphy_cfg = {
>>>> .lanes = 1,
>>>> .offsets = &qmp_ufs_offsets,
>>>> + .max_supported_gear = UFS_HS_G3,
>>>> .tbls = {
>>>> .serdes = msm8996_ufsphy_serdes,
>>>> @@ -969,6 +1017,7 @@ static const struct qmp_phy_cfg sa8775p_ufsphy_cfg = {
>>>> .lanes = 2,
>>>> .offsets = &qmp_ufs_offsets,
>>>> + .max_supported_gear = UFS_HS_G4,
>>>> .tbls = {
>>>> .serdes = sm8350_ufsphy_serdes,
>>>> @@ -984,13 +1033,14 @@ static const struct qmp_phy_cfg sa8775p_ufsphy_cfg = {
>>>> .serdes = sm8350_ufsphy_hs_b_serdes,
>>>> .serdes_num = ARRAY_SIZE(sm8350_ufsphy_hs_b_serdes),
>>>> },
>>>> - .tbls_hs_g4 = {
>>>> + .tbls_hs_overlay[0] = {
>>>> .tx = sm8350_ufsphy_g4_tx,
>>>> .tx_num = ARRAY_SIZE(sm8350_ufsphy_g4_tx),
>>>> .rx = sm8350_ufsphy_g4_rx,
>>>> .rx_num = ARRAY_SIZE(sm8350_ufsphy_g4_rx),
>>>> .pcs = sm8350_ufsphy_g4_pcs,
>>>> .pcs_num = ARRAY_SIZE(sm8350_ufsphy_g4_pcs),
>>>> + .max_gear = UFS_HS_G4,
>>>> },
>>>> .clk_list = sm8450_ufs_phy_clk_l,
>>>> .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l),
>>>> @@ -1003,6 +1053,7 @@ static const struct qmp_phy_cfg sc7280_ufsphy_cfg = {
>>>> .lanes = 2,
>>>> .offsets = &qmp_ufs_offsets,
>>>> + .max_supported_gear = UFS_HS_G4,
>>>> .tbls = {
>>>> .serdes = sm8150_ufsphy_serdes,
>>>> @@ -1018,13 +1069,14 @@ static const struct qmp_phy_cfg sc7280_ufsphy_cfg = {
>>>> .serdes = sm8150_ufsphy_hs_b_serdes,
>>>> .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes),
>>>> },
>>>> - .tbls_hs_g4 = {
>>>> + .tbls_hs_overlay[0] = {
>>>> .tx = sm8250_ufsphy_hs_g4_tx,
>>>> .tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx),
>>>> .rx = sc7280_ufsphy_hs_g4_rx,
>>>> .rx_num = ARRAY_SIZE(sc7280_ufsphy_hs_g4_rx),
>>>> .pcs = sm8150_ufsphy_hs_g4_pcs,
>>>> .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs),
>>>> + .max_gear = UFS_HS_G4,
>>>> },
>>>> .clk_list = sm8450_ufs_phy_clk_l,
>>>> .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l),
>>>> @@ -1037,6 +1089,7 @@ static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = {
>>>> .lanes = 2,
>>>> .offsets = &qmp_ufs_offsets,
>>>> + .max_supported_gear = UFS_HS_G4,
>>>> .tbls = {
>>>> .serdes = sm8350_ufsphy_serdes,
>>>> @@ -1052,13 +1105,14 @@ static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = {
>>>> .serdes = sm8350_ufsphy_hs_b_serdes,
>>>> .serdes_num = ARRAY_SIZE(sm8350_ufsphy_hs_b_serdes),
>>>> },
>>>> - .tbls_hs_g4 = {
>>>> + .tbls_hs_overlay[0] = {
>>>> .tx = sm8350_ufsphy_g4_tx,
>>>> .tx_num = ARRAY_SIZE(sm8350_ufsphy_g4_tx),
>>>> .rx = sm8350_ufsphy_g4_rx,
>>>> .rx_num = ARRAY_SIZE(sm8350_ufsphy_g4_rx),
>>>> .pcs = sm8350_ufsphy_g4_pcs,
>>>> .pcs_num = ARRAY_SIZE(sm8350_ufsphy_g4_pcs),
>>>> + .max_gear = UFS_HS_G4,
>>>> },
>>>> .clk_list = sdm845_ufs_phy_clk_l,
>>>> .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
>>>> @@ -1071,6 +1125,7 @@ static const struct qmp_phy_cfg sdm845_ufsphy_cfg = {
>>>> .lanes = 2,
>>>> .offsets = &qmp_ufs_offsets,
>>>> + .max_supported_gear = UFS_HS_G3,
>>>> .tbls = {
>>>> .serdes = sdm845_ufsphy_serdes,
>>>> @@ -1099,6 +1154,7 @@ static const struct qmp_phy_cfg sm6115_ufsphy_cfg = {
>>>> .lanes = 1,
>>>> .offsets = &qmp_ufs_offsets,
>>>> + .max_supported_gear = UFS_HS_G3,
>>>> .tbls = {
>>>> .serdes = sm6115_ufsphy_serdes,
>>>> @@ -1127,6 +1183,7 @@ static const struct qmp_phy_cfg sm7150_ufsphy_cfg = {
>>>> .lanes = 1,
>>>> .offsets = &qmp_ufs_offsets,
>>>> + .max_supported_gear = UFS_HS_G3,
>>>> .tbls = {
>>>> .serdes = sdm845_ufsphy_serdes,
>>>> @@ -1155,6 +1212,7 @@ static const struct qmp_phy_cfg sm8150_ufsphy_cfg = {
>>>> .lanes = 2,
>>>> .offsets = &qmp_ufs_offsets,
>>>> + .max_supported_gear = UFS_HS_G4,
>>>> .tbls = {
>>>> .serdes = sm8150_ufsphy_serdes,
>>>> @@ -1170,13 +1228,14 @@ static const struct qmp_phy_cfg sm8150_ufsphy_cfg = {
>>>> .serdes = sm8150_ufsphy_hs_b_serdes,
>>>> .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes),
>>>> },
>>>> - .tbls_hs_g4 = {
>>>> + .tbls_hs_overlay[0] = {
>>>> .tx = sm8150_ufsphy_hs_g4_tx,
>>>> .tx_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_tx),
>>>> .rx = sm8150_ufsphy_hs_g4_rx,
>>>> .rx_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_rx),
>>>> .pcs = sm8150_ufsphy_hs_g4_pcs,
>>>> .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs),
>>>> + .max_gear = UFS_HS_G4,
>>>> },
>>>> .clk_list = sdm845_ufs_phy_clk_l,
>>>> .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
>>>> @@ -1189,6 +1248,7 @@ static const struct qmp_phy_cfg sm8250_ufsphy_cfg = {
>>>> .lanes = 2,
>>>> .offsets = &qmp_ufs_offsets,
>>>> + .max_supported_gear = UFS_HS_G4,
>>>> .tbls = {
>>>> .serdes = sm8150_ufsphy_serdes,
>>>> @@ -1204,13 +1264,14 @@ static const struct qmp_phy_cfg sm8250_ufsphy_cfg = {
>>>> .serdes = sm8150_ufsphy_hs_b_serdes,
>>>> .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes),
>>>> },
>>>> - .tbls_hs_g4 = {
>>>> + .tbls_hs_overlay[0] = {
>>>> .tx = sm8250_ufsphy_hs_g4_tx,
>>>> .tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx),
>>>> .rx = sm8250_ufsphy_hs_g4_rx,
>>>> .rx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_rx),
>>>> .pcs = sm8150_ufsphy_hs_g4_pcs,
>>>> .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs),
>>>> + .max_gear = UFS_HS_G4,
>>>> },
>>>> .clk_list = sdm845_ufs_phy_clk_l,
>>>> .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
>>>> @@ -1223,6 +1284,7 @@ static const struct qmp_phy_cfg sm8350_ufsphy_cfg = {
>>>> .lanes = 2,
>>>> .offsets = &qmp_ufs_offsets,
>>>> + .max_supported_gear = UFS_HS_G4,
>>>> .tbls = {
>>>> .serdes = sm8350_ufsphy_serdes,
>>>> @@ -1238,13 +1300,14 @@ static const struct qmp_phy_cfg sm8350_ufsphy_cfg = {
>>>> .serdes = sm8350_ufsphy_hs_b_serdes,
>>>> .serdes_num = ARRAY_SIZE(sm8350_ufsphy_hs_b_serdes),
>>>> },
>>>> - .tbls_hs_g4 = {
>>>> + .tbls_hs_overlay[0] = {
>>>> .tx = sm8350_ufsphy_g4_tx,
>>>> .tx_num = ARRAY_SIZE(sm8350_ufsphy_g4_tx),
>>>> .rx = sm8350_ufsphy_g4_rx,
>>>> .rx_num = ARRAY_SIZE(sm8350_ufsphy_g4_rx),
>>>> .pcs = sm8350_ufsphy_g4_pcs,
>>>> .pcs_num = ARRAY_SIZE(sm8350_ufsphy_g4_pcs),
>>>> + .max_gear = UFS_HS_G4,
>>>> },
>>>> .clk_list = sdm845_ufs_phy_clk_l,
>>>> .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
>>>> @@ -1257,6 +1320,7 @@ static const struct qmp_phy_cfg sm8450_ufsphy_cfg = {
>>>> .lanes = 2,
>>>> .offsets = &qmp_ufs_offsets,
>>>> + .max_supported_gear = UFS_HS_G4,
>>>> .tbls = {
>>>> .serdes = sm8350_ufsphy_serdes,
>>>> @@ -1272,13 +1336,14 @@ static const struct qmp_phy_cfg sm8450_ufsphy_cfg = {
>>>> .serdes = sm8350_ufsphy_hs_b_serdes,
>>>> .serdes_num = ARRAY_SIZE(sm8350_ufsphy_hs_b_serdes),
>>>> },
>>>> - .tbls_hs_g4 = {
>>>> + .tbls_hs_overlay[0] = {
>>>> .tx = sm8350_ufsphy_g4_tx,
>>>> .tx_num = ARRAY_SIZE(sm8350_ufsphy_g4_tx),
>>>> .rx = sm8350_ufsphy_g4_rx,
>>>> .rx_num = ARRAY_SIZE(sm8350_ufsphy_g4_rx),
>>>> .pcs = sm8350_ufsphy_g4_pcs,
>>>> .pcs_num = ARRAY_SIZE(sm8350_ufsphy_g4_pcs),
>>>> + .max_gear = UFS_HS_G4,
>>>> },
>>>> .clk_list = sm8450_ufs_phy_clk_l,
>>>> .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l),
>>>> @@ -1291,6 +1356,7 @@ static const struct qmp_phy_cfg sm8550_ufsphy_cfg = {
>>>> .lanes = 2,
>>>> .offsets = &qmp_ufs_offsets_v6,
>>>> + .max_supported_gear = UFS_HS_G5,
>>>> .tbls = {
>>>> .serdes = sm8550_ufsphy_serdes,
>>>> @@ -1306,6 +1372,26 @@ static const struct qmp_phy_cfg sm8550_ufsphy_cfg = {
>>>> .serdes = sm8550_ufsphy_hs_b_serdes,
>>>> .serdes_num = ARRAY_SIZE(sm8550_ufsphy_hs_b_serdes),
>>>> },
>>>> + .tbls_hs_overlay[0] = {
>>>> + .serdes = sm8550_ufsphy_g4_serdes,
>>>> + .serdes_num = ARRAY_SIZE(sm8550_ufsphy_g4_serdes),
>>>> + .tx = sm8550_ufsphy_g4_tx,
>>>> + .tx_num = ARRAY_SIZE(sm8550_ufsphy_g4_tx),
>>>> + .rx = sm8550_ufsphy_g4_rx,
>>>> + .rx_num = ARRAY_SIZE(sm8550_ufsphy_g4_rx),
>>>> + .pcs = sm8550_ufsphy_g4_pcs,
>>>> + .pcs_num = ARRAY_SIZE(sm8550_ufsphy_g4_pcs),
>>>> + .max_gear = UFS_HS_G4,
>>>> + },
>>>> + .tbls_hs_overlay[1] = {
>>>> + .serdes = sm8550_ufsphy_g5_serdes,
>>>> + .serdes_num = ARRAY_SIZE(sm8550_ufsphy_g5_serdes),
>>>> + .rx = sm8550_ufsphy_g5_rx,
>>>> + .rx_num = ARRAY_SIZE(sm8550_ufsphy_g5_rx),
>>>> + .pcs = sm8550_ufsphy_g5_pcs,
>>>> + .pcs_num = ARRAY_SIZE(sm8550_ufsphy_g5_pcs),
>>>> + .max_gear = UFS_HS_G5,
>>>> + },
>>>> .clk_list = sdm845_ufs_phy_clk_l,
>>>> .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
>>>> .vreg_list = qmp_phy_vreg_l,
>>>> @@ -1368,17 +1454,55 @@ static void qmp_ufs_pcs_init(struct qmp_ufs *qmp, const struct qmp_phy_cfg_tbls
>>>> qmp_ufs_configure(pcs, tbls->pcs, tbls->pcs_num);
>>>> }
>>>> +static int qmp_ufs_get_gear_overlay(struct qmp_ufs *qmp, const struct qmp_phy_cfg *cfg)
>>>> +{
>>>> + u32 max_gear, floor_max_gear = cfg->max_supported_gear;
>>>> + int i = NUM_OVERLAY - 1;
>>>
>>> Just use i directly in the for loop. Also, please rename "i" with "idx" to make
>>> it clear.
>>
>> OK
>>
>>>
>>>> + int ret = -EINVAL;
>>>> +
>>>> + for (; i >= 0; i --) {
>>>
>>> i--
>>>
>>>> + max_gear = cfg->tbls_hs_overlay[i].max_gear;
>>>> +
>>>> + if (max_gear == 0)
>>>> + continue;
>>>
>>> You are setting max_gear even for targets with a single overlay. How can this
>>> become 0?
>>
>> Say 8550 has two overlays, 8450 has one overlay. We are sweeping all
>> overlays as NUM_OVERLAY == 2, so for 8450, there is one overlay initialized,
>> another one not initialized (max_gear == 0), we are skipping the one which
>> is not initialized.
>>
>
> This is confusing at its best :) Please check for the existence of the actual
> table instead. Like,
>
> for (idx = NUM_OVERLAY - 1; i >= 0, i--) {
>
> /* Skip if the table is not available */
> if (!cfg->tbls_hs_overlay[i].serdes)
> continue;
>
> ...
> }
We cannot expect overlay must has its own serdes, or tx/rx/pcs, hence I
am checking max_gear intead of any specific member.
>
>>>
>>>> +
>>>> + /* Direct matching, bail */
>>>> + if (qmp->submode == max_gear)
>>>> + return i;
>>>> +
>>>> + /* If no direct matching, the lowest gear is the best matching */
>>>> + if (max_gear < floor_max_gear) {
>>>> + ret = i;
>>>> + floor_max_gear = max_gear;
>>>> + }
>>>> + }
>>>> +
>>>> + return ret;
>>>> +}
>>>> +
>>>> static void qmp_ufs_init_registers(struct qmp_ufs *qmp, const struct qmp_phy_cfg *cfg)
>>>> {
>>>> + int i;
>>>> + bool apply_overlay = false;
>>>> +
>>>> + i = qmp_ufs_get_gear_overlay(qmp, cfg);
>>>> + if (i >= 0)
>>>> + apply_overlay = true;
>>>
>>> How about?
>>>
>>> ```
>>> int idx;
>>>
>>> idx = qmp_ufs_get_gear_overlay(qmp, cfg);
>>>
>>> qmp_ufs_serdes_init(qmp, &cfg->tbls);
>>> qmp_ufs_lanes_init(qmp, &cfg->tbls);
>>> ...
>>>
>>> if (idx >= 0) {
>>> qmp_ufs_serdes_init(qmp, &cfg->tbls_hs_overlay[idx]);
>>> qmp_ufs_lanes_init(qmp, &cfg->tbls_hs_overlay[idx]);
>>> ...
>>> }
>>> ```
>>>
>>> Since the ordering doesn't matter for init sequence, you can program the overlay
>>> tables under a single condition.
>>
>> We can do that, but we need to be careful. When I say (in my previous reply)
>> the ordering does not matter, that saying is from the UFS PHY HPG doc.
>> However, in SW implementation, the 'tbls_hs_b' is actually overwriting one
>> COM_VCO_TUNE_MAP register, the same register is also programmed by common
>> table or overlay table. So qmp_ufs_serdes_init(qmp, &cfg->tbls_hs_b) should
>> come after overlays.
>>
>
> Then you can program tbls_hs_b after overlay tables. Wouldn't that work?
I am programming tbls_hs_b after overlay tables, just a heads up in case
you are surprised :).
Thanks,
Can Guo.
>
> - Mani
>
>> Thanks,
>> Can Guo.
>>
>>>
>>> - Mani
>>>
>
More information about the linux-phy
mailing list