[PATCH v9 07/12] clk: meson: add vclk driver
Jerome Brunet
jbrunet at baylibre.com
Mon Nov 27 08:24:03 PST 2023
On Mon 27 Nov 2023 at 17:14, Neil Armstrong <neil.armstrong at linaro.org> wrote:
> On 24/11/2023 15:41, Jerome Brunet wrote:
>> On Fri 24 Nov 2023 at 09:41, Neil Armstrong <neil.armstrong at linaro.org>
>> wrote:
>>
>>> The VCLK and VCLK_DIV clocks have supplementary bits.
>>>
>>> The VCLK has a "SOFT RESET" bit to toggle after the whole
>>> VCLK sub-tree rate has been set, this is implemented in
>>> the gate enable callback.
>>>
>>> The VCLK_DIV clocks as enable and reset bits used to disable
>>> and reset the divider, associated with CLK_SET_RATE_GATE it ensures
>>> the rate is set while the divider is disabled and in reset mode.
>>>
>>> The VCLK_DIV enable bit isn't implemented as a gate since it's part
>>> of the divider logic and vendor does this exact sequence to ensure
>>> the divider is correctly set.
>>>
>>> Signed-off-by: Neil Armstrong <neil.armstrong at linaro.org>
>>> ---
>>> drivers/clk/meson/Kconfig | 5 ++
>>> drivers/clk/meson/Makefile | 1 +
>>> drivers/clk/meson/vclk.c | 141 +++++++++++++++++++++++++++++++++++++++++++++
>>> drivers/clk/meson/vclk.h | 51 ++++++++++++++++
>>> 4 files changed, 198 insertions(+)
>>>
>>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>>> index 29ffd14d267b..59a40a49f8e1 100644
>>> --- a/drivers/clk/meson/Kconfig
>>> +++ b/drivers/clk/meson/Kconfig
>>> @@ -30,6 +30,10 @@ config COMMON_CLK_MESON_VID_PLL_DIV
>>> tristate
>>> select COMMON_CLK_MESON_REGMAP
>>> +config COMMON_CLK_MESON_VCLK
>>> + tristate
>>> + select COMMON_CLK_MESON_REGMAP
>>> +
>>> config COMMON_CLK_MESON_CLKC_UTILS
>>> tristate
>>> @@ -140,6 +144,7 @@ config COMMON_CLK_G12A
>>> select COMMON_CLK_MESON_EE_CLKC
>>> select COMMON_CLK_MESON_CPU_DYNDIV
>>> select COMMON_CLK_MESON_VID_PLL_DIV
>>> + select COMMON_CLK_MESON_VCLK
>> This particular line belong in the next patch
>>
>>> select MFD_SYSCON
>>> help
>>> Support for the clock controller on Amlogic S905D2, S905X2 and S905Y2
>>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>>> index 9ee4b954c896..9ba43fe7a07a 100644
>>> --- a/drivers/clk/meson/Makefile
>>> +++ b/drivers/clk/meson/Makefile
>>> @@ -12,6 +12,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_PLL) += clk-pll.o
>>> obj-$(CONFIG_COMMON_CLK_MESON_REGMAP) += clk-regmap.o
>>> obj-$(CONFIG_COMMON_CLK_MESON_SCLK_DIV) += sclk-div.o
>>> obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
>>> +obj-$(CONFIG_COMMON_CLK_MESON_VCLK) += vclk.o
>>> # Amlogic Clock controllers
>>> diff --git a/drivers/clk/meson/vclk.c b/drivers/clk/meson/vclk.c
>>> new file mode 100644
>>> index 000000000000..47f08a52b49f
>>> --- /dev/null
>>> +++ b/drivers/clk/meson/vclk.c
>>> @@ -0,0 +1,141 @@
>>> +// SPDX-License-Identifier: GPL-2.0
>>> +/*
>>> + * Copyright (c) 2023 Neil Armstrong <neil.armstrong at linaro.org>
>>> + */
>>> +
>>> +#include <linux/module.h>
>>> +#include "vclk.h"
>>> +
>>> +/* The VCLK gate has a supplementary reset bit to pulse after ungating */
>>> +
>>> +static inline struct clk_regmap_vclk_data *
>>> +clk_get_regmap_vclk_data(struct clk_regmap *clk)
>>> +{
>>> + return (struct clk_regmap_vclk_data *)clk->data;
>>> +}
>>> +
>>> +static int clk_regmap_vclk_enable(struct clk_hw *hw)
>>> +{
>>> + struct clk_regmap *clk = to_clk_regmap(hw);
>>> + struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>>> +
>>> + meson_parm_write(clk->map, &vclk->enable, 1);
>>> +
>>> + /* Do a reset pulse */
>>> + meson_parm_write(clk->map, &vclk->reset, 1);
>>> + meson_parm_write(clk->map, &vclk->reset, 0);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static void clk_regmap_vclk_disable(struct clk_hw *hw)
>>> +{
>>> + struct clk_regmap *clk = to_clk_regmap(hw);
>>> + struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>>> +
>>> + meson_parm_write(clk->map, &vclk->enable, 0);
>>> +}
>>> +
>>> +static int clk_regmap_vclk_is_enabled(struct clk_hw *hw)
>>> +{
>>> + struct clk_regmap *clk = to_clk_regmap(hw);
>>> + struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>>> +
>>> + return meson_parm_read(clk->map, &vclk->enable);
>>> +}
>>> +
>>> +const struct clk_ops clk_regmap_vclk_ops = {
>>> + .enable = clk_regmap_vclk_enable,
>>> + .disable = clk_regmap_vclk_disable,
>>> + .is_enabled = clk_regmap_vclk_is_enabled,
>>> +};
>>> +EXPORT_SYMBOL_GPL(clk_regmap_vclk_ops);
>> s/clk_regmap_vclk/meson_vclk at least for what is exported, ideally most
>> all the code.
>> I get clk_regmap_ comes from code copied from clk_regmap.c.
>> The reason the this part is different (and not using parm) if that when
>> I converted amlogic to regmap, I hope we could make this generic,
>> possibly converging between aml and qcom (which was the only other
>> platform using regmap for clock at the time). This is why clk_regmap.c
>> is a bit different from the other driver.
>> For the aml specific drivers, best to look at the mpll or cpu-dyndiv one.
>>
>>> +
>>> +/* The VCLK Divider has supplementary reset & enable bits */
>>> +
>>> +static inline struct clk_regmap_vclk_div_data *
>>> +clk_get_regmap_vclk_div_data(struct clk_regmap *clk)
>>> +{
>>> + return (struct clk_regmap_vclk_div_data *)clk->data;
>>> +}
>>> +
>>> +static unsigned long clk_regmap_vclk_div_recalc_rate(struct clk_hw *hw,
>>> + unsigned long prate)
>>> +{
>>> + struct clk_regmap *clk = to_clk_regmap(hw);
>>> + struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>> +
>>> + return divider_recalc_rate(hw, prate, meson_parm_read(clk->map, &vclk->div),
>>> + vclk->table, vclk->flags, vclk->div.width);
>>> +}
>>> +
>>> +static int clk_regmap_vclk_div_determine_rate(struct clk_hw *hw,
>>> + struct clk_rate_request *req)
>>> +{
>>> + struct clk_regmap *clk = to_clk_regmap(hw);
>>> + struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>> +
>>> + return divider_determine_rate(hw, req, vclk->table, vclk->div.width,
>>> + vclk->flags);
>>> +}
>>> +
>>> +static int clk_regmap_vclk_div_set_rate(struct clk_hw *hw, unsigned long rate,
>>> + unsigned long parent_rate)
>>> +{
>>> + struct clk_regmap *clk = to_clk_regmap(hw);
>>> + struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>> + int ret;
>>> +
>>> + ret = divider_get_val(rate, parent_rate, vclk->table, vclk->div.width,
>>> + vclk->flags);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + meson_parm_write(clk->map, &vclk->div, ret);
>>> +
>>> + return 0;
>>> +};
>>> +
>>> +static int clk_regmap_vclk_div_enable(struct clk_hw *hw)
>>> +{
>>> + struct clk_regmap *clk = to_clk_regmap(hw);
>>> + struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>> +
>>> + /* Unreset the divider when ungating */
>>> + meson_parm_write(clk->map, &vclk->reset, 0);
>>> + meson_parm_write(clk->map, &vclk->enable, 1);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static void clk_regmap_vclk_div_disable(struct clk_hw *hw)
>>> +{
>>> + struct clk_regmap *clk = to_clk_regmap(hw);
>>> + struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>> +
>>> + /* Reset the divider when gating */
>>> + meson_parm_write(clk->map, &vclk->enable, 0);
>>> + meson_parm_write(clk->map, &vclk->reset, 1);
>>> +}
>>> +
>>> +static int clk_regmap_vclk_div_is_enabled(struct clk_hw *hw)
>>> +{
>>> + struct clk_regmap *clk = to_clk_regmap(hw);
>>> + struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>> +
>>> + return meson_parm_read(clk->map, &vclk->enable);
>>> +}
>>> +
>>> +const struct clk_ops clk_regmap_vclk_div_ops = {
>>> + .recalc_rate = clk_regmap_vclk_div_recalc_rate,
>>> + .determine_rate = clk_regmap_vclk_div_determine_rate,
>>> + .set_rate = clk_regmap_vclk_div_set_rate,
>>> + .enable = clk_regmap_vclk_div_enable,
>>> + .disable = clk_regmap_vclk_div_disable,
>>> + .is_enabled = clk_regmap_vclk_div_is_enabled,
>>> +};
>>> +EXPORT_SYMBOL_GPL(clk_regmap_vclk_div_ops);
>>> +
>>> +MODULE_DESCRIPTION("Amlogic vclk clock driver");
>>> +MODULE_AUTHOR("Neil Armstrong <neil.armstrong at linaro.org>");
>>> +MODULE_LICENSE("GPL v2");
>>> diff --git a/drivers/clk/meson/vclk.h b/drivers/clk/meson/vclk.h
>>> new file mode 100644
>>> index 000000000000..4f25d7ad2717
>>> --- /dev/null
>>> +++ b/drivers/clk/meson/vclk.h
>
> Is vclk.c/h ok ? clk-vclk doesn't look pretty, but I can switch to it to
> keep files organized.
I don't have a strong opinion about it.
I would have suggested vclk-div.c/h - like sclk ... but you do have gate
ops in there, so ... :/
This made me realize that one does not really go without the other.
It is more a coherent block, isn't it ?
Would it make more sense to have these 2 merged in a single clk_ops ?
It's bit late to point this out, sorry about that.
I let you decide whether to merge the ops or not and which name to pick.
If you keep them separated, meson_vclk_gate_ops instead of just
meson_vclk_ops, to make things clear.
>
> Neil
>
>>> @@ -0,0 +1,51 @@
>>> +/* SPDX-License-Identifier: GPL-2.0 */
>>> +/*
>>> + * Copyright (c) 2023 Neil Armstrong <neil.armstrong at linaro.org>
>>> + */
>>> +
>>> +#ifndef __VCLK_H
>>> +#define __VCLK_H
>> This is too generic.
>> Please add the MESON prefix like the other clock driver please.
>>
>>> +
>>> +#include "clk-regmap.h"
>>> +#include "parm.h"
>>> +
>>> +/**
>>> + * struct clk_regmap_vclk_data - vclk regmap backed specific data
>>> + *
>>> + * @enable: vclk enable field
>>> + * @reset: vclk reset field
>>> + * @flags: hardware-specific flags
>>> + *
>>> + * Flags:
>>> + * Same as clk_gate except CLK_GATE_HIWORD_MASK which is ignored
>>> + */
>>> +struct clk_regmap_vclk_data {
>>> + struct parm enable;
>>> + struct parm reset;
>>> + u8 flags;
>>> +};
>>> +
>>> +extern const struct clk_ops clk_regmap_vclk_ops;
>>> +
>>> +/**
>>> + * struct clk_regmap_vclk_div_data - vclk_div regmap back specific data
>>> + *
>>> + * @div: divider field
>>> + * @enable: vclk divider enable field
>>> + * @reset: vclk divider reset field
>>> + * @table: array of value/divider pairs, last entry should have div = 0
>>> + *
>>> + * Flags:
>>> + * Same as clk_divider except CLK_DIVIDER_HIWORD_MASK which is ignored
>>> + */
>>> +struct clk_regmap_vclk_div_data {
>>> + struct parm div;
>>> + struct parm enable;
>>> + struct parm reset;
>>> + const struct clk_div_table *table;
>>> + u8 flags;
>>> +};
>>> +
>>> +extern const struct clk_ops clk_regmap_vclk_div_ops;
>>> +
>>> +#endif /* __VCLK_H */
>>
--
Jerome
More information about the linux-phy
mailing list