[PATCH v3 3/3] phy: qcom-qmp-pcie: Add support for keeping refclk always on

[Krishna chaitanya chundru]

In PCIe low power states like L1.1 or L1.2 the phy will stop
supplying refclk to endpoint. If endpoint asserts clkreq to bring
back link L0, then RC needs to provide refclk to endpoint.

Some platforms with pcie switch fail to drive the clkreq signal to
the host from the endpoints because of the switch board design.
Due to that refclk needs to supplied to the endpoint always.

Add a flag to keep refclk always supplied to endpoint.

Signed-off-by: Krishna chaitanya chundru <quic_krichai at quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
index 7fdf9b2596b6..e95f677817f7 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
@@ -43,6 +43,8 @@
 /* QPHY_PCS_STATUS bit */
 #define PHYSTATUS				BIT(6)
 #define PHYSTATUS_4_20				BIT(7)
+/* PCS_PCIE_ENDPOINT_REFCLK_CNTRL */
+#define EPCLK_ALWAYS_ON_EN			BIT(6)
 
 #define PHY_INIT_COMPLETE_TIMEOUT		10000
 
@@ -2264,6 +2266,8 @@ struct qmp_pcie {
 	struct phy *phy;
 	int mode;
 
+	bool refclk_always_on;
+
 	struct clk_fixed_rate pipe_clk_fixed;
 };
 
@@ -3179,6 +3183,10 @@ static void qmp_pcie_init_registers(struct qmp_pcie *qmp, const struct qmp_phy_c
 	qmp_pcie_configure(pcs, tbls->pcs, tbls->pcs_num);
 	qmp_pcie_configure(pcs_misc, tbls->pcs_misc, tbls->pcs_misc_num);
 
+	if (qmp->refclk_always_on && cfg->regs[QPHY_PCS_ENDPOINT_REFCLK_CNTRL])
+		qphy_setbits(pcs_misc, cfg->regs[QPHY_PCS_ENDPOINT_REFCLK_CNTRL],
+			     EPCLK_ALWAYS_ON_EN);
+
 	if (cfg->lanes >= 4 && qmp->tcsr_4ln_config) {
 		qmp_pcie_configure(serdes, cfg->serdes_4ln_tbl, cfg->serdes_4ln_num);
 		qmp_pcie_init_port_b(qmp, tbls);
@@ -3701,6 +3709,12 @@ static int qmp_pcie_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_node_put;
 
+	qmp->refclk_always_on = of_property_read_bool(dev->of_node, "qcom,refclk-always-on");
+	if (qmp->refclk_always_on && !qmp->cfg->regs[QPHY_PCS_ENDPOINT_REFCLK_CNTRL]) {
+		dev_err(dev, "refclk is always on is present but refclk cntrl offset is not present\n");
+		goto err_node_put;
+	}
+
 	ret = phy_pipe_clk_register(qmp, np);
 	if (ret)
 		goto err_node_put;

-- 
2.42.0