[PATCH 2/2] phy: qcom-qmp-pcie: Add support for keeping refclk always on

[Krishna Chaitanya Chundru]

On 11/6/2023 5:43 PM, Dmitry Baryshkov wrote:
> On Mon, 6 Nov 2023 at 13:53, Krishna chaitanya chundru
> <quic_krichai at quicinc.com> wrote:
>> In PCIe low power states like L1.1 or L1.2 the phy will stop
>> supplying refclk to endpoint. If endpoint asserts clkreq to bring
>> back link L0, then RC needs to provide refclk to endpoint.
>>
>> If there is some issues in platform with clkreq signal propagation
>> to host and due to that host will not send refclk which results PCIe link
>> down. For those platforms  phy needs to provide refclk even in low power
>> states.
>>
>> Add a flag which indicates refclk is always supplied to endpoint.
>>
>> Signed-off-by: Krishna chaitanya chundru <quic_krichai at quicinc.com>
>> ---
>>   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 21 +++++++++++++++++----
>>   1 file changed, 17 insertions(+), 4 deletions(-)
>>
>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
>> index a63ca7424974..d7e377a7d96e 100644
>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
>> @@ -43,6 +43,8 @@
>>   /* QPHY_PCS_STATUS bit */
>>   #define PHYSTATUS                              BIT(6)
>>   #define PHYSTATUS_4_20                         BIT(7)
>> +/* PCS_PCIE_ENDPOINT_REFCLK_CNTRL */
>> +#define EPCLK_ALWAYS_ON_EN                     BIT(6)
>
>>   #define PHY_INIT_COMPLETE_TIMEOUT              10000
>>
>> @@ -77,6 +79,7 @@ enum qphy_reg_layout {
>>          QPHY_START_CTRL,
>>          QPHY_PCS_STATUS,
>>          QPHY_PCS_POWER_DOWN_CONTROL,
>> +       QPHY_PCS_ENDPOINT_REFCLK_CNTRL,
>>          /* Keep last to ensure regs_layout arrays are properly initialized */
>>          QPHY_LAYOUT_SIZE
>>   };
>> @@ -103,10 +106,11 @@ static const unsigned int sdm845_qhp_pciephy_regs_layout[QPHY_LAYOUT_SIZE] = {
>>   };
>>
>>   static const unsigned int pciephy_v4_regs_layout[QPHY_LAYOUT_SIZE] = {
>> -       [QPHY_SW_RESET]                 = QPHY_V4_PCS_SW_RESET,
>> -       [QPHY_START_CTRL]               = QPHY_V4_PCS_START_CONTROL,
>> -       [QPHY_PCS_STATUS]               = QPHY_V4_PCS_PCS_STATUS1,
>> -       [QPHY_PCS_POWER_DOWN_CONTROL]   = QPHY_V4_PCS_POWER_DOWN_CONTROL,
>> +       [QPHY_SW_RESET]                         = QPHY_V4_PCS_SW_RESET,
>> +       [QPHY_START_CTRL]                       = QPHY_V4_PCS_START_CONTROL,
>> +       [QPHY_PCS_STATUS]                       = QPHY_V4_PCS_PCS_STATUS1,
>> +       [QPHY_PCS_POWER_DOWN_CONTROL]           = QPHY_V4_PCS_POWER_DOWN_CONTROL,
> No unnecessary whitespace changes, please.
I will remove above white space and keep below change as it is as it is 
throwing error as white space required there
>
>> +       [QPHY_PCS_ENDPOINT_REFCLK_CNTRL]        = QPHY_V4_PCS_PCIE_ENDPOINT_REFCLK_CNTRL,
> Any other platform having this register?
we have this register for other platforms also I will add that register 
in which ever versions it exits in next patch
>
>>   };
>>
>>   static const unsigned int pciephy_v5_regs_layout[QPHY_LAYOUT_SIZE] = {
>> @@ -2244,6 +2248,8 @@ struct qmp_pcie {
>>          struct phy *phy;
>>          int mode;
>>
>> +       bool refclk_always_on;
>> +
>>          struct clk_fixed_rate pipe_clk_fixed;
>>   };
>>
>> @@ -3159,6 +3165,10 @@ static void qmp_pcie_init_registers(struct qmp_pcie *qmp, const struct qmp_phy_c
>>          qmp_pcie_configure(pcs, tbls->pcs, tbls->pcs_num);
>>          qmp_pcie_configure(pcs_misc, tbls->pcs_misc, tbls->pcs_misc_num);
>>
>> +       if (qmp->refclk_always_on && cfg->regs[QPHY_PCS_ENDPOINT_REFCLK_CNTRL])
>> +               qphy_setbits(pcs_misc, cfg->regs[QPHY_PCS_ENDPOINT_REFCLK_CNTRL],
>> +                            EPCLK_ALWAYS_ON_EN);
>> +
>>          if (cfg->lanes >= 4 && qmp->tcsr_4ln_config) {
>>                  qmp_pcie_configure(serdes, cfg->serdes_4ln_tbl, cfg->serdes_4ln_num);
>>                  qmp_pcie_init_port_b(qmp, tbls);
>> @@ -3681,6 +3691,9 @@ static int qmp_pcie_probe(struct platform_device *pdev)
>>          if (ret)
>>                  goto err_node_put;
>>
>> +       qmp->refclk_always_on = of_property_read_bool(dev->of_node,
>> +                                                     "qcom,refclk-always-on");
> Error out if !cfg->regs[QPHY_PCS_ENDPOINT_REFCLK_CNTRL]).
> Otherwise your DT value can be silently ignored.

sure I will add this in next patch series.

- Krishna Chaitanya.

>> +
>>          ret = phy_pipe_clk_register(qmp, np);
>>          if (ret)
>>                  goto err_node_put;
>>
>> --
>> 2.42.0
>>
>