[PATCH 10/41] arm64: dts: qcom: ipq6018: switch USB QMP PHY to new style of bindings

[Dmitry Baryshkov]

Change the USB QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes).

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
---
 arch/arm64/boot/dts/qcom/ipq6018.dtsi | 31 +++++++++++----------------
 1 file changed, 12 insertions(+), 19 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index 9ff4e9d45065..ff540bfcc062 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -220,31 +220,24 @@ qusb_phy_1: qusb at 59000 {
 
 		ssphy_0: ssphy at 78000 {
 			compatible = "qcom,ipq6018-qmp-usb3-phy";
-			reg = <0x0 0x00078000 0x0 0x1c4>;
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
+			reg = <0x0 0x00078000 0x0 0x1000>;
 
 			clocks = <&gcc GCC_USB0_AUX_CLK>,
-				 <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, <&xo>;
-			clock-names = "aux", "cfg_ahb", "ref";
+				 <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
+				 <&xo>,
+				 <&gcc GCC_USB0_PIPE_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb",
+				      "ref",
+				      "pipe";
+			clock-output-names = "gcc_usb0_pipe_clk_src";
+			#clock-cells = <0>;
+			#phy-cells = <0>;
 
 			resets = <&gcc GCC_USB0_PHY_BCR>,
 				 <&gcc GCC_USB3PHY_0_PHY_BCR>;
 			reset-names = "phy","common";
 			status = "disabled";
-
-			usb0_ssphy: phy at 78200 {
-				reg = <0x0 0x00078200 0x0 0x130>, /* Tx */
-				      <0x0 0x00078400 0x0 0x200>, /* Rx */
-				      <0x0 0x00078800 0x0 0x1f8>, /* PCS */
-				      <0x0 0x00078600 0x0 0x044>; /* PCS misc */
-				#phy-cells = <0>;
-				#clock-cells = <0>;
-				clocks = <&gcc GCC_USB0_PIPE_CLK>;
-				clock-names = "pipe0";
-				clock-output-names = "gcc_usb0_pipe_clk_src";
-			};
 		};
 
 		qusb_phy_0: qusb at 79000 {
@@ -553,7 +546,7 @@ dwc_0: usb at 8a00000 {
 				compatible = "snps,dwc3";
 				reg = <0x0 0x08a00000 0x0 0xcd00>;
 				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
-				phys = <&qusb_phy_0>, <&usb0_ssphy>;
+				phys = <&qusb_phy_0>, <&ssphy_0>;
 				phy-names = "usb2-phy", "usb3-phy";
 				clocks = <&xo>;
 				clock-names = "ref";
-- 
2.30.2