[PATCH v2 5/6] arm64: dts: qcom: sa8775p: Add pcie0 and pcie1 nodes
Mrinmay Sarkar
quic_msarkar at quicinc.com
Thu Jul 13 22:08:37 PDT 2023
Add pcie dtsi nodes for two controllers found on sa8775p platform.
Signed-off-by: Mrinmay Sarkar <quic_msarkar at quicinc.com>
---
arch/arm64/boot/dts/qcom/sa8775p.dtsi | 204 +++++++++++++++++++++++++++++++++-
1 file changed, 202 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
index 59eedfc..7b55cb7 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
@@ -481,8 +481,8 @@
<0>,
<0>,
<0>,
- <0>,
- <0>,
+ <&pcie0_phy>,
+ <&pcie1_phy>,
<0>,
<0>,
<0>;
@@ -2357,4 +2357,204 @@
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
};
+
+ pcie0: pci at 1c00000{
+ compatible = "qcom,pcie-sa8775p";
+ reg = <0x0 0x01c00000 0x0 0x3000>,
+ <0x0 0x40000000 0x0 0xf20>,
+ <0x0 0x40000f20 0x0 0xa8>,
+ <0x0 0x40001000 0x0 0x4000>,
+ <0x0 0x40100000 0x0 0x100000>,
+ <0x0 0x01c03000 0x0 0x1000>;
+ reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,
+ <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
+ bus-range = <0x00 0xff>;
+
+ dma-coherent;
+
+ linux,pci-domain = <0>;
+ num-lanes = <2>;
+
+ interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi0", "msi1", "msi2", "msi3",
+ "msi4", "msi5", "msi6", "msi7";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc GIC_SPI 434 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 2 &intc GIC_SPI 435 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 3 &intc GIC_SPI 438 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 4 &intc GIC_SPI 439 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+ <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>;
+
+ clock-names = "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a";
+
+ assigned-clocks = <&gcc GCC_PCIE_0_AUX_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ interconnects = <&pcie_anoc MASTER_PCIE_0 0 &mc_virt SLAVE_EBI1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_0 0>;
+ interconnect-names = "pcie-mem", "cpu-pcie";
+
+ iommu-map = <0x0 &pcie_smmu 0x0000 0x1>,
+ <0x100 &pcie_smmu 0x0001 0x1>;
+
+ resets = <&gcc GCC_PCIE_0_BCR>;
+ reset-names = "pci";
+ power-domains = <&gcc PCIE_0_GDSC>;
+
+ phys = <&pcie0_phy>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie0_phy: phy at 1c04000 {
+ compatible = "qcom,sa8775p-qmp-gen4x2-pcie-phy";
+ reg = <0x0 0x1c04000 0x0 0x2000>;
+
+ clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+ <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_CLKREF_EN>,
+ <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>,
+ <&gcc GCC_PCIE_0_PIPE_CLK>,
+ <&gcc GCC_PCIE_0_PIPEDIV2_CLK>,
+ <&gcc GCC_PCIE_0_PHY_AUX_CLK>;
+
+ clock-names = "aux", "cfg_ahb", "ref", "rchng", "pipe",
+ "pipediv2", "phy_aux";
+
+ assigned-clocks = <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+ reset-names = "phy";
+
+ #clock-cells = <0>;
+ clock-output-names = "pcie_0_pipe_clk";
+
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ pcie1: pci at 1c10000{
+ compatible = "qcom,pcie-sa8775p";
+ reg = <0x0 0x01c10000 0x0 0x3000>,
+ <0x0 0x60000000 0x0 0xf20>,
+ <0x0 0x60000f20 0x0 0xa8>,
+ <0x0 0x60001000 0x0 0x4000>,
+ <0x0 0x60100000 0x0 0x100000>,
+ <0x0 0x01c13000 0x0 0x1000>;
+ reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>,
+ <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x1fd00000>;
+ bus-range = <0x00 0xff>;
+
+ dma-coherent;
+
+ linux,pci-domain = <1>;
+ num-lanes = <4>;
+
+ interrupts = <GIC_SPI 519 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi0", "msi1", "msi2", "msi3",
+ "msi4", "msi5", "msi6", "msi7";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 2 &intc GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 3 &intc GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 4 &intc GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+ <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>;
+
+ clock-names = "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a";
+
+ assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ interconnects = <&pcie_anoc MASTER_PCIE_1 0 &mc_virt SLAVE_EBI1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_1 0>;
+ interconnect-names = "pcie-mem", "cpu-pcie";
+
+ iommu-map = <0x0 &pcie_smmu 0x0080 0x1>,
+ <0x100 &pcie_smmu 0x0081 0x1>;
+
+ resets = <&gcc GCC_PCIE_1_BCR>;
+ reset-names = "pci";
+ power-domains = <&gcc PCIE_1_GDSC>;
+
+ phys = <&pcie1_phy>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie1_phy: phy at 1c14000 {
+ compatible = "qcom,sa8775p-qmp-gen4x4-pcie-phy";
+ reg = <0x0 0x1c14000 0x0 0x4000>;
+
+ clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+ <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_CLKREF_EN>,
+ <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>,
+ <&gcc GCC_PCIE_1_PIPE_CLK>,
+ <&gcc GCC_PCIE_1_PIPEDIV2_CLK>,
+ <&gcc GCC_PCIE_1_PHY_AUX_CLK>;
+
+ clock-names = "aux", "cfg_ahb", "ref", "rchng", "pipe",
+ "pipediv2", "phy_aux";
+
+ assigned-clocks = <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ resets = <&gcc GCC_PCIE_1_PHY_BCR>;
+ reset-names = "phy";
+
+ #clock-cells = <0>;
+ clock-output-names = "pcie_1_pipe_clk";
+
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
};
--
2.7.4
More information about the linux-phy
mailing list