[PATCH v1 3/4] Revert "phy: intel: Add Thunder Bay eMMC PHY support"
Vinod Koul
vkoul at kernel.org
Tue Jan 24 03:59:47 PST 2023
On 24-01-23, 11:14, rashmi.a at intel.com wrote:
> From: "A, Rashmi" <rashmi.a at intel.com>
>
> This reverts commit 97004c1a4c52b4357169290158a130ca0b7caae1.
Please send a patch to drop the driver etc.. this revert makes no sense
to me
>
> Revert Thunder Bay specific code as the product got cancelled
> and there are no end customers.
>
> Signed-off-by: A, Rashmi <rashmi.a at intel.com>
> Reviewed-by: Hunter, Adrian <adrian.hunter at intel.com>
> ---
> drivers/phy/intel/Kconfig | 10 -
> drivers/phy/intel/Makefile | 1 -
> drivers/phy/intel/phy-intel-thunderbay-emmc.c | 509 ------------------
> 3 files changed, 520 deletions(-)
> delete mode 100644 drivers/phy/intel/phy-intel-thunderbay-emmc.c
>
> diff --git a/drivers/phy/intel/Kconfig b/drivers/phy/intel/Kconfig
> index 18a3cc5b98c0..ac42bb2fb394 100644
> --- a/drivers/phy/intel/Kconfig
> +++ b/drivers/phy/intel/Kconfig
> @@ -46,13 +46,3 @@ config PHY_INTEL_LGM_EMMC
> select GENERIC_PHY
> help
> Enable this to support the Intel EMMC PHY
> -
> -config PHY_INTEL_THUNDERBAY_EMMC
> - tristate "Intel Thunder Bay eMMC PHY driver"
> - depends on OF && (ARCH_THUNDERBAY || COMPILE_TEST)
> - select GENERIC_PHY
> - help
> - This option enables support for Intel Thunder Bay SoC eMMC PHY.
> -
> - To compile this driver as a module, choose M here: the module
> - will be called phy-intel-thunderbay-emmc.ko.
> diff --git a/drivers/phy/intel/Makefile b/drivers/phy/intel/Makefile
> index b7321d56b0bb..14550981a707 100644
> --- a/drivers/phy/intel/Makefile
> +++ b/drivers/phy/intel/Makefile
> @@ -3,4 +3,3 @@ obj-$(CONFIG_PHY_INTEL_KEEMBAY_EMMC) += phy-intel-keembay-emmc.o
> obj-$(CONFIG_PHY_INTEL_KEEMBAY_USB) += phy-intel-keembay-usb.o
> obj-$(CONFIG_PHY_INTEL_LGM_COMBO) += phy-intel-lgm-combo.o
> obj-$(CONFIG_PHY_INTEL_LGM_EMMC) += phy-intel-lgm-emmc.o
> -obj-$(CONFIG_PHY_INTEL_THUNDERBAY_EMMC) += phy-intel-thunderbay-emmc.o
> diff --git a/drivers/phy/intel/phy-intel-thunderbay-emmc.c b/drivers/phy/intel/phy-intel-thunderbay-emmc.c
> deleted file mode 100644
> index 593f6970b81e..000000000000
> --- a/drivers/phy/intel/phy-intel-thunderbay-emmc.c
> +++ /dev/null
> @@ -1,509 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0-only
> -/*
> - * Intel ThunderBay eMMC PHY driver
> - *
> - * Copyright (C) 2021 Intel Corporation
> - *
> - */
> -
> -#include <linux/clk.h>
> -#include <linux/delay.h>
> -#include <linux/io.h>
> -#include <linux/iopoll.h>
> -#include <linux/module.h>
> -#include <linux/of.h>
> -#include <linux/phy/phy.h>
> -#include <linux/platform_device.h>
> -
> -/* eMMC/SD/SDIO core/phy configuration registers */
> -#define CTRL_CFG_0 0x00
> -#define CTRL_CFG_1 0x04
> -#define CTRL_PRESET_0 0x08
> -#define CTRL_PRESET_1 0x0c
> -#define CTRL_PRESET_2 0x10
> -#define CTRL_PRESET_3 0x14
> -#define CTRL_PRESET_4 0x18
> -#define CTRL_CFG_2 0x1c
> -#define CTRL_CFG_3 0x20
> -#define PHY_CFG_0 0x24
> -#define PHY_CFG_1 0x28
> -#define PHY_CFG_2 0x2c
> -#define PHYBIST_CTRL 0x30
> -#define SDHC_STAT3 0x34
> -#define PHY_STAT 0x38
> -#define PHYBIST_STAT_0 0x3c
> -#define PHYBIST_STAT_1 0x40
> -#define EMMC_AXI 0x44
> -
> -/* CTRL_PRESET_3 */
> -#define CTRL_PRESET3_MASK GENMASK(31, 0)
> -#define CTRL_PRESET3_SHIFT 0
> -
> -/* CTRL_CFG_0 bit fields */
> -#define SUPPORT_HS_MASK BIT(26)
> -#define SUPPORT_HS_SHIFT 26
> -
> -#define SUPPORT_8B_MASK BIT(24)
> -#define SUPPORT_8B_SHIFT 24
> -
> -/* CTRL_CFG_1 bit fields */
> -#define SUPPORT_SDR50_MASK BIT(28)
> -#define SUPPORT_SDR50_SHIFT 28
> -#define SLOT_TYPE_MASK GENMASK(27, 26)
> -#define SLOT_TYPE_OFFSET 26
> -#define SUPPORT_64B_MASK BIT(24)
> -#define SUPPORT_64B_SHIFT 24
> -#define SUPPORT_HS400_MASK BIT(2)
> -#define SUPPORT_HS400_SHIFT 2
> -#define SUPPORT_DDR50_MASK BIT(1)
> -#define SUPPORT_DDR50_SHIFT 1
> -#define SUPPORT_SDR104_MASK BIT(0)
> -#define SUPPORT_SDR104_SHIFT 0
> -
> -/* PHY_CFG_0 bit fields */
> -#define SEL_DLY_TXCLK_MASK BIT(29)
> -#define SEL_DLY_TXCLK_SHIFT 29
> -#define SEL_DLY_RXCLK_MASK BIT(28)
> -#define SEL_DLY_RXCLK_SHIFT 28
> -
> -#define OTAP_DLY_ENA_MASK BIT(27)
> -#define OTAP_DLY_ENA_SHIFT 27
> -#define OTAP_DLY_SEL_MASK GENMASK(26, 23)
> -#define OTAP_DLY_SEL_SHIFT 23
> -#define ITAP_CHG_WIN_MASK BIT(22)
> -#define ITAP_CHG_WIN_SHIFT 22
> -#define ITAP_DLY_ENA_MASK BIT(21)
> -#define ITAP_DLY_ENA_SHIFT 21
> -#define ITAP_DLY_SEL_MASK GENMASK(20, 16)
> -#define ITAP_DLY_SEL_SHIFT 16
> -#define RET_ENB_MASK BIT(15)
> -#define RET_ENB_SHIFT 15
> -#define RET_EN_MASK BIT(14)
> -#define RET_EN_SHIFT 14
> -#define DLL_IFF_MASK GENMASK(13, 11)
> -#define DLL_IFF_SHIFT 11
> -#define DLL_EN_MASK BIT(10)
> -#define DLL_EN_SHIFT 10
> -#define DLL_TRIM_ICP_MASK GENMASK(9, 6)
> -#define DLL_TRIM_ICP_SHIFT 6
> -#define RETRIM_EN_MASK BIT(5)
> -#define RETRIM_EN_SHIFT 5
> -#define RETRIM_MASK BIT(4)
> -#define RETRIM_SHIFT 4
> -#define DR_TY_MASK GENMASK(3, 1)
> -#define DR_TY_SHIFT 1
> -#define PWR_DOWN_MASK BIT(0)
> -#define PWR_DOWN_SHIFT 0
> -
> -/* PHY_CFG_1 bit fields */
> -#define REN_DAT_MASK GENMASK(19, 12)
> -#define REN_DAT_SHIFT 12
> -#define REN_CMD_MASK BIT(11)
> -#define REN_CMD_SHIFT 11
> -#define REN_STRB_MASK BIT(10)
> -#define REN_STRB_SHIFT 10
> -#define PU_STRB_MASK BIT(20)
> -#define PU_STRB_SHIFT 20
> -
> -/* PHY_CFG_2 bit fields */
> -#define CLKBUF_MASK GENMASK(24, 21)
> -#define CLKBUF_SHIFT 21
> -#define SEL_STRB_MASK GENMASK(20, 13)
> -#define SEL_STRB_SHIFT 13
> -#define SEL_FREQ_MASK GENMASK(12, 10)
> -#define SEL_FREQ_SHIFT 10
> -
> -/* PHY_STAT bit fields */
> -#define CAL_DONE BIT(6)
> -#define DLL_RDY BIT(5)
> -
> -#define OTAP_DLY 0x0
> -#define ITAP_DLY 0x0
> -#define STRB 0x33
> -
> -/* From ACS_eMMC51_16nFFC_RO1100_Userguide_v1p0.pdf p17 */
> -#define FREQSEL_200M_170M 0x0
> -#define FREQSEL_170M_140M 0x1
> -#define FREQSEL_140M_110M 0x2
> -#define FREQSEL_110M_80M 0x3
> -#define FREQSEL_80M_50M 0x4
> -#define FREQSEL_275M_250M 0x5
> -#define FREQSEL_250M_225M 0x6
> -#define FREQSEL_225M_200M 0x7
> -
> -/* Phy power status */
> -#define PHY_UNINITIALIZED 0
> -#define PHY_INITIALIZED 1
> -
> -/*
> - * During init(400KHz) phy_settings will be called with 200MHZ clock
> - * To avoid incorrectly setting the phy for init(400KHZ) "phy_power_sts" is used.
> - * When actual clock is set always phy is powered off once and then powered on.
> - * (sdhci_arasan_set_clock). That feature will be used to identify whether the
> - * settings are for init phy_power_on or actual clock phy_power_on
> - * 0 --> init settings
> - * 1 --> actual settings
> - */
> -
> -struct thunderbay_emmc_phy {
> - void __iomem *reg_base;
> - struct clk *emmcclk;
> - int phy_power_sts;
> -};
> -
> -static inline void update_reg(struct thunderbay_emmc_phy *tbh_phy, u32 offset,
> - u32 mask, u32 shift, u32 val)
> -{
> - u32 tmp;
> -
> - tmp = readl(tbh_phy->reg_base + offset);
> - tmp &= ~mask;
> - tmp |= val << shift;
> - writel(tmp, tbh_phy->reg_base + offset);
> -}
> -
> -static int thunderbay_emmc_phy_power(struct phy *phy, bool power_on)
> -{
> - struct thunderbay_emmc_phy *tbh_phy = phy_get_drvdata(phy);
> - unsigned int freqsel = FREQSEL_200M_170M;
> - unsigned long rate;
> - static int lock;
> - u32 val;
> - int ret;
> -
> - /* Disable DLL */
> - rate = clk_get_rate(tbh_phy->emmcclk);
> - switch (rate) {
> - case 200000000:
> - /* lock dll only when it is used, i.e only if SEL_DLY_TXCLK/RXCLK are 0 */
> - update_reg(tbh_phy, PHY_CFG_0, DLL_EN_MASK, DLL_EN_SHIFT, 0x0);
> - break;
> -
> - /* dll lock not required for other frequencies */
> - case 50000000 ... 52000000:
> - case 400000:
> - default:
> - break;
> - }
> -
> - if (!power_on)
> - return 0;
> -
> - rate = clk_get_rate(tbh_phy->emmcclk);
> - switch (rate) {
> - case 170000001 ... 200000000:
> - freqsel = FREQSEL_200M_170M;
> - break;
> -
> - case 140000001 ... 170000000:
> - freqsel = FREQSEL_170M_140M;
> - break;
> -
> - case 110000001 ... 140000000:
> - freqsel = FREQSEL_140M_110M;
> - break;
> -
> - case 80000001 ... 110000000:
> - freqsel = FREQSEL_110M_80M;
> - break;
> -
> - case 50000000 ... 80000000:
> - freqsel = FREQSEL_80M_50M;
> - break;
> -
> - case 250000001 ... 275000000:
> - freqsel = FREQSEL_275M_250M;
> - break;
> -
> - case 225000001 ... 250000000:
> - freqsel = FREQSEL_250M_225M;
> - break;
> -
> - case 200000001 ... 225000000:
> - freqsel = FREQSEL_225M_200M;
> - break;
> - default:
> - break;
> - }
> - /* Clock rate is checked against upper limit. It may fall low during init */
> - if (rate > 200000000)
> - dev_warn(&phy->dev, "Unsupported rate: %lu\n", rate);
> -
> - udelay(5);
> -
> - if (lock == 0) {
> - /* PDB will be done only once per boot */
> - update_reg(tbh_phy, PHY_CFG_0, PWR_DOWN_MASK,
> - PWR_DOWN_SHIFT, 0x1);
> - lock = 1;
> - /*
> - * According to the user manual, it asks driver to wait 5us for
> - * calpad busy trimming. However it is documented that this value is
> - * PVT(A.K.A. process, voltage and temperature) relevant, so some
> - * failure cases are found which indicates we should be more tolerant
> - * to calpad busy trimming.
> - */
> - ret = readl_poll_timeout(tbh_phy->reg_base + PHY_STAT,
> - val, (val & CAL_DONE), 10, 50);
> - if (ret) {
> - dev_err(&phy->dev, "caldone failed, ret=%d\n", ret);
> - return ret;
> - }
> - }
> - rate = clk_get_rate(tbh_phy->emmcclk);
> - switch (rate) {
> - case 200000000:
> - /* Set frequency of the DLL operation */
> - update_reg(tbh_phy, PHY_CFG_2, SEL_FREQ_MASK, SEL_FREQ_SHIFT, freqsel);
> -
> - /* Enable DLL */
> - update_reg(tbh_phy, PHY_CFG_0, DLL_EN_MASK, DLL_EN_SHIFT, 0x1);
> -
> - /*
> - * After enabling analog DLL circuits docs say that we need 10.2 us if
> - * our source clock is at 50 MHz and that lock time scales linearly
> - * with clock speed. If we are powering on the PHY and the card clock
> - * is super slow (like 100kHz) this could take as long as 5.1 ms as
> - * per the math: 10.2 us * (50000000 Hz / 100000 Hz) => 5.1 ms
> - * hopefully we won't be running at 100 kHz, but we should still make
> - * sure we wait long enough.
> - *
> - * NOTE: There appear to be corner cases where the DLL seems to take
> - * extra long to lock for reasons that aren't understood. In some
> - * extreme cases we've seen it take up to over 10ms (!). We'll be
> - * generous and give it 50ms.
> - */
> - ret = readl_poll_timeout(tbh_phy->reg_base + PHY_STAT,
> - val, (val & DLL_RDY), 10, 50 * USEC_PER_MSEC);
> - if (ret) {
> - dev_err(&phy->dev, "dllrdy failed, ret=%d\n", ret);
> - return ret;
> - }
> - break;
> -
> - default:
> - break;
> - }
> - return 0;
> -}
> -
> -static int thunderbay_emmc_phy_init(struct phy *phy)
> -{
> - struct thunderbay_emmc_phy *tbh_phy = phy_get_drvdata(phy);
> -
> - tbh_phy->emmcclk = clk_get(&phy->dev, "emmcclk");
> -
> - return PTR_ERR_OR_ZERO(tbh_phy->emmcclk);
> -}
> -
> -static int thunderbay_emmc_phy_exit(struct phy *phy)
> -{
> - struct thunderbay_emmc_phy *tbh_phy = phy_get_drvdata(phy);
> -
> - clk_put(tbh_phy->emmcclk);
> -
> - return 0;
> -}
> -
> -static int thunderbay_emmc_phy_power_on(struct phy *phy)
> -{
> - struct thunderbay_emmc_phy *tbh_phy = phy_get_drvdata(phy);
> - unsigned long rate;
> -
> - /* Overwrite capability bits configurable in bootloader */
> - update_reg(tbh_phy, CTRL_CFG_0,
> - SUPPORT_HS_MASK, SUPPORT_HS_SHIFT, 0x1);
> - update_reg(tbh_phy, CTRL_CFG_0,
> - SUPPORT_8B_MASK, SUPPORT_8B_SHIFT, 0x1);
> - update_reg(tbh_phy, CTRL_CFG_1,
> - SUPPORT_SDR50_MASK, SUPPORT_SDR50_SHIFT, 0x1);
> - update_reg(tbh_phy, CTRL_CFG_1,
> - SUPPORT_DDR50_MASK, SUPPORT_DDR50_SHIFT, 0x1);
> - update_reg(tbh_phy, CTRL_CFG_1,
> - SUPPORT_SDR104_MASK, SUPPORT_SDR104_SHIFT, 0x1);
> - update_reg(tbh_phy, CTRL_CFG_1,
> - SUPPORT_HS400_MASK, SUPPORT_HS400_SHIFT, 0x1);
> - update_reg(tbh_phy, CTRL_CFG_1,
> - SUPPORT_64B_MASK, SUPPORT_64B_SHIFT, 0x1);
> -
> - if (tbh_phy->phy_power_sts == PHY_UNINITIALIZED) {
> - /* Indicates initialization, settings for init, same as 400KHZ setting */
> - update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_TXCLK_MASK, SEL_DLY_TXCLK_SHIFT, 0x1);
> - update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_RXCLK_MASK, SEL_DLY_RXCLK_SHIFT, 0x1);
> - update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_ENA_MASK, ITAP_DLY_ENA_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_SEL_MASK, ITAP_DLY_SEL_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_ENA_MASK, OTAP_DLY_ENA_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_SEL_MASK, OTAP_DLY_SEL_SHIFT, 0);
> - update_reg(tbh_phy, PHY_CFG_0, DLL_TRIM_ICP_MASK, DLL_TRIM_ICP_SHIFT, 0);
> - update_reg(tbh_phy, PHY_CFG_0, DR_TY_MASK, DR_TY_SHIFT, 0x1);
> -
> - } else if (tbh_phy->phy_power_sts == PHY_INITIALIZED) {
> - /* Indicates actual clock setting */
> - rate = clk_get_rate(tbh_phy->emmcclk);
> - switch (rate) {
> - case 200000000:
> - update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_TXCLK_MASK,
> - SEL_DLY_TXCLK_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_RXCLK_MASK,
> - SEL_DLY_RXCLK_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_ENA_MASK,
> - ITAP_DLY_ENA_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_SEL_MASK,
> - ITAP_DLY_SEL_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_ENA_MASK,
> - OTAP_DLY_ENA_SHIFT, 0x1);
> - update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_SEL_MASK,
> - OTAP_DLY_SEL_SHIFT, 2);
> - update_reg(tbh_phy, PHY_CFG_0, DLL_TRIM_ICP_MASK,
> - DLL_TRIM_ICP_SHIFT, 0x8);
> - update_reg(tbh_phy, PHY_CFG_0, DR_TY_MASK,
> - DR_TY_SHIFT, 0x1);
> - /* For HS400 only */
> - update_reg(tbh_phy, PHY_CFG_2, SEL_STRB_MASK,
> - SEL_STRB_SHIFT, STRB);
> - break;
> -
> - case 50000000 ... 52000000:
> - /* For both HS and DDR52 this setting works */
> - update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_TXCLK_MASK,
> - SEL_DLY_TXCLK_SHIFT, 0x1);
> - update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_RXCLK_MASK,
> - SEL_DLY_RXCLK_SHIFT, 0x1);
> - update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_ENA_MASK,
> - ITAP_DLY_ENA_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_SEL_MASK,
> - ITAP_DLY_SEL_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_ENA_MASK,
> - OTAP_DLY_ENA_SHIFT, 0x1);
> - update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_SEL_MASK,
> - OTAP_DLY_SEL_SHIFT, 4);
> - update_reg(tbh_phy, PHY_CFG_0, DLL_TRIM_ICP_MASK,
> - DLL_TRIM_ICP_SHIFT, 0x8);
> - update_reg(tbh_phy, PHY_CFG_0,
> - DR_TY_MASK, DR_TY_SHIFT, 0x1);
> - break;
> -
> - case 400000:
> - update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_TXCLK_MASK,
> - SEL_DLY_TXCLK_SHIFT, 0x1);
> - update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_RXCLK_MASK,
> - SEL_DLY_RXCLK_SHIFT, 0x1);
> - update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_ENA_MASK,
> - ITAP_DLY_ENA_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_SEL_MASK,
> - ITAP_DLY_SEL_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_ENA_MASK,
> - OTAP_DLY_ENA_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_SEL_MASK,
> - OTAP_DLY_SEL_SHIFT, 0);
> - update_reg(tbh_phy, PHY_CFG_0, DLL_TRIM_ICP_MASK,
> - DLL_TRIM_ICP_SHIFT, 0);
> - update_reg(tbh_phy, PHY_CFG_0, DR_TY_MASK, DR_TY_SHIFT, 0x1);
> - break;
> -
> - default:
> - update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_TXCLK_MASK,
> - SEL_DLY_TXCLK_SHIFT, 0x1);
> - update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_RXCLK_MASK,
> - SEL_DLY_RXCLK_SHIFT, 0x1);
> - update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_ENA_MASK,
> - ITAP_DLY_ENA_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_SEL_MASK,
> - ITAP_DLY_SEL_SHIFT, 0x0);
> - update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_ENA_MASK,
> - OTAP_DLY_ENA_SHIFT, 0x1);
> - update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_SEL_MASK,
> - OTAP_DLY_SEL_SHIFT, 2);
> - update_reg(tbh_phy, PHY_CFG_0, DLL_TRIM_ICP_MASK,
> - DLL_TRIM_ICP_SHIFT, 0x8);
> - update_reg(tbh_phy, PHY_CFG_0, DR_TY_MASK,
> - DR_TY_SHIFT, 0x1);
> - break;
> - }
> - /* Reset, init seq called without phy_power_off, this indicates init seq */
> - tbh_phy->phy_power_sts = PHY_UNINITIALIZED;
> - }
> -
> - update_reg(tbh_phy, PHY_CFG_0, RETRIM_EN_MASK, RETRIM_EN_SHIFT, 0x1);
> - update_reg(tbh_phy, PHY_CFG_0, RETRIM_MASK, RETRIM_SHIFT, 0x0);
> -
> - return thunderbay_emmc_phy_power(phy, 1);
> -}
> -
> -static int thunderbay_emmc_phy_power_off(struct phy *phy)
> -{
> - struct thunderbay_emmc_phy *tbh_phy = phy_get_drvdata(phy);
> -
> - tbh_phy->phy_power_sts = PHY_INITIALIZED;
> -
> - return thunderbay_emmc_phy_power(phy, 0);
> -}
> -
> -static const struct phy_ops thunderbay_emmc_phy_ops = {
> - .init = thunderbay_emmc_phy_init,
> - .exit = thunderbay_emmc_phy_exit,
> - .power_on = thunderbay_emmc_phy_power_on,
> - .power_off = thunderbay_emmc_phy_power_off,
> - .owner = THIS_MODULE,
> -};
> -
> -static const struct of_device_id thunderbay_emmc_phy_of_match[] = {
> - { .compatible = "intel,thunderbay-emmc-phy",
> - (void *)&thunderbay_emmc_phy_ops },
> - {}
> -};
> -MODULE_DEVICE_TABLE(of, thunderbay_emmc_phy_of_match);
> -
> -static int thunderbay_emmc_phy_probe(struct platform_device *pdev)
> -{
> - struct thunderbay_emmc_phy *tbh_phy;
> - struct phy_provider *phy_provider;
> - struct device *dev = &pdev->dev;
> - const struct of_device_id *id;
> - struct phy *generic_phy;
> - struct resource *res;
> -
> - if (!dev->of_node)
> - return -ENODEV;
> -
> - tbh_phy = devm_kzalloc(dev, sizeof(*tbh_phy), GFP_KERNEL);
> - if (!tbh_phy)
> - return -ENOMEM;
> -
> - res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> - tbh_phy->reg_base = devm_ioremap_resource(&pdev->dev, res);
> - if (IS_ERR(tbh_phy->reg_base))
> - return PTR_ERR(tbh_phy->reg_base);
> -
> - tbh_phy->phy_power_sts = PHY_UNINITIALIZED;
> - id = of_match_node(thunderbay_emmc_phy_of_match, pdev->dev.of_node);
> - if (!id) {
> - dev_err(dev, "failed to get match_node\n");
> - return -EINVAL;
> - }
> -
> - generic_phy = devm_phy_create(dev, dev->of_node, id->data);
> - if (IS_ERR(generic_phy)) {
> - dev_err(dev, "failed to create PHY\n");
> - return PTR_ERR(generic_phy);
> - }
> -
> - phy_set_drvdata(generic_phy, tbh_phy);
> - phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> -
> - return PTR_ERR_OR_ZERO(phy_provider);
> -}
> -
> -static struct platform_driver thunderbay_emmc_phy_driver = {
> - .probe = thunderbay_emmc_phy_probe,
> - .driver = {
> - .name = "thunderbay-emmc-phy",
> - .of_match_table = thunderbay_emmc_phy_of_match,
> - },
> -};
> -module_platform_driver(thunderbay_emmc_phy_driver);
> -
> -MODULE_AUTHOR("Nandhini S <nandhini.srikandan at intel.com>");
> -MODULE_AUTHOR("Rashmi A <rashmi.a at intel.com>");
> -MODULE_DESCRIPTION("Intel Thunder Bay eMMC PHY driver");
> -MODULE_LICENSE("GPL v2");
> --
> 2.17.1
--
~Vinod
More information about the linux-phy
mailing list