[PATCH v3 02/12] dt-bindings: display: mediatek: add MT8195 hdmi bindings

[AngeloGioacchino Del Regno]

Il 02/01/23 16:19, Guillaume Ranquet ha scritto:
> On Mon, 02 Jan 2023 15:14, AngeloGioacchino Del Regno
> <angelogioacchino.delregno at collabora.com> wrote:
>> Il 02/01/23 14:38, Guillaume Ranquet ha scritto:
>>> On Mon, 26 Dec 2022 06:18, CK Hu (胡俊光) <ck.hu at mediatek.com> wrote:
>>>> Hi, Guillaume:
>>>>
>>>> On Fri, 2022-11-04 at 15:09 +0100, Guillaume Ranquet wrote:
>>>>> Add mt8195 SoC bindings for hdmi and hdmi-ddc
>>>>>
>>>>> On mt8195 the ddc i2c controller is part of the hdmi IP block and
>>>>> thus has no
>>>>> specific register range, power domain or interrupt, making it simpler
>>>>> than its the legacy "mediatek,hdmi-ddc" binding.
>>>>>
>>>>> Signed-off-by: Guillaume Ranquet <granquet at baylibre.com>
>>>>> ---
>>>>>
>>>>
>>>> [snip]
>>>>
>>>>> a/Documentation/devicetree/bindings/display/mediatek/mediatek,mt8195-
>>>>> hdmi-ddc.yaml
>>>>> b/Documentation/devicetree/bindings/display/mediatek/mediatek,mt8195-
>>>>> hdmi-ddc.yaml
>>>>> new file mode 100644
>>>>> index 000000000000..2dc273689584
>>>>> --- /dev/null
>>>>> +++
>>>>> b/Documentation/devicetree/bindings/display/mediatek/mediatek,mt8195-
>>>>> hdmi-ddc.yaml
>>>>> @@ -0,0 +1,51 @@
>>>>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>>>>> +%YAML 1.2
>>>>> +---
>>>>> +$id:
>>>>> https://urldefense.com/v3/__http://devicetree.org/schemas/display/mediatek/mediatek,mt8195-hdmi-ddc.yaml*__;Iw!!CTRNKA9wMg0ARbw!wwVQuq5lzW0lvUFUkVXPWT8cIu96xdkn4tMams1E55qyxEZmgV1i0WfpOlq57w$
>>>>>
>>>>> +$schema:
>>>>> https://urldefense.com/v3/__http://devicetree.org/meta-schemas/core.yaml*__;Iw!!CTRNKA9wMg0ARbw!wwVQuq5lzW0lvUFUkVXPWT8cIu96xdkn4tMams1E55qyxEZmgV1i0WdSGOSxzw$
>>>>>
>>>>> +
>>>>> +title: Mediatek HDMI DDC for mt8195
>>>>> +
>>>>> +maintainers:
>>>>> +  - CK Hu <ck.hu at mediatek.com>
>>>>> +  - Jitao shi <jitao.shi at mediatek.com>
>>>>> +
>>>>> +description: |
>>>>> +  The HDMI DDC i2c controller is used to interface with the HDMI DDC
>>>>> pins.
>>>>> +
>>>>> +properties:
>>>>> +  compatible:
>>>>> +    enum:
>>>>> +      - mediatek,mt8195-hdmi-ddc
>>>>> +
>>>>> +  clocks:
>>>>> +    maxItems: 1
>>>>> +
>>>>> +  clock-names:
>>>>> +    items:
>>>>> +      - const: ddc
>>>>> +
>>>>> +  mediatek,hdmi:
>>>>> +    $ref: /schemas/types.yaml#/definitions/phandle
>>>>> +    description:
>>>>> +      A phandle to the mt8195 hdmi controller
>>>>> +
>>>>> +required:
>>>>> +  - compatible
>>>>> +  - clocks
>>>>> +  - clock-names
>>>>> +
>>>>> +additionalProperties: false
>>>>> +
>>>>> +examples:
>>>>> +  - |
>>>>> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
>>>>> +    #include <dt-bindings/interrupt-controller/irq.h>
>>>>> +    hdmiddc0: i2c {
>>>>> +      compatible = "mediatek,mt8195-hdmi-ddc";
>>>>> +      mediatek,hdmi = <&hdmi0>;
>>>>> +      clocks = <&clk26m>;
>>>>> +      clock-names = "ddc";
>>>>> +    };
>>>>
>>>> I think we should not have a virtual device. This ddc is part of
>>>> mt8195-hdmi device, so just keep mt8195-hdmi, and let mt8195-hdmi
>>>> driver to probe the sub driver of ddc driver.
>>>>
>>>> Regards,
>>>> CK
>>>
>>> Hi CK,
>>>
>>> Thx for your input.
>>> Though I would strongly prefer to keep the ddc as a separate "virtual device".
>>>
>>> It aligns better with the goal of reusing as much code as possible
>>> from the HDMI V1 IP,
>>> which is something you have been advocating since V1 of this patch
>>> quite some time ago
>>> and has shaped this patch.
>>>
>>> To me we are in a state that is clean and avoids branching in the hdmi
>>> common code.
>>> Would you reconsider and allow the use of that virtual device?
>>>
>>> Thx,
>>> Guillaume.
>>>
>>
>> You can as well keep the DDC as a separated driver, but register in the HDMI v1 and
>> v2 driver at probe time.
>>
>> Doing that, you won't need any devicetree node specific to any virtual device :-)
>>
>> Cheers,
>> Angelo
>>
>>
> 
> Sure, but does it make any sense for HDMI v1?
> As the ddc in v1 is a real device which (in theory) can be reused by other IPs.
> 
> I would see either v1 and v2 ddc exposed as a devicetree node (which
> is what I favor).
> Or v1 as a devicetree node and v2 probed directly from the hdmi code base.
> 

The last option looks sensible, since v1 has an external ddc, but on v2 it's
integrated.

v1 -> dt probe
v2 -> driver probe

> Thx,
> Guillaume.