[PATCH 7/7] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes
Manivannan Sadhasivam
mani at kernel.org
Fri Feb 24 00:59:02 PST 2023
On Tue, Feb 14, 2023 at 10:11:35PM +0530, Devi Priya wrote:
> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>
Please split the board devicetree changes into a separate patch.
> Co-developed-by: Anusha Rao <quic_anusha at quicinc.com>
> Signed-off-by: Anusha Rao <quic_anusha at quicinc.com>
> Signed-off-by: Devi Priya <quic_devipriy at quicinc.com>
> ---
> arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 28 ++
> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 477 ++++++++++++++++++-
> 2 files changed, 499 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> index 2c8430197ec0..21b53f34ce84 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
> @@ -8,6 +8,7 @@
>
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> #include "ipq9574.dtsi"
>
> / {
> @@ -29,6 +30,33 @@
> status = "okay";
> };
>
> +&pcie1_phy {
> + status = "okay";
No PHY power supply needed? Same comment for rest of the PHY nodes.
> +};
> +
> +&pcie1_x1 {
No need to add a suffix to node label indicating the lane config.
> + perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
What about "wake" pin? Don't you need pinctrl definitions for these GPIOs?
Same comment for rest of the PCIe nodes.
> + status = "okay";
> +};
> +
> +&pcie2_phy {
> + status = "okay";
> +};
> +
> +&pcie2_x2 {
> + perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&pcie3_phy {
> + status = "okay";
> +};
> +
> +&pcie3_x2 {
> + perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> &sdhc_1 {
> pinctrl-0 = <&sdc_default_state>;
> pinctrl-names = "default";
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> index 062f80798ebb..a32dbdeb5bed 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> @@ -6,8 +6,8 @@
> * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
> */
>
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/qcom,ipq9574-gcc.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/reset/qcom,ipq9574-gcc.h>
>
> / {
> @@ -22,11 +22,41 @@
> #clock-cells = <0>;
> };
>
> + pcie30_phy0_pipe_clk: pcie30_phy0_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> + pcie30_phy1_pipe_clk: pcie30_phy1_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> + pcie30_phy2_pipe_clk: pcie30_phy2_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
> +
> + pcie30_phy3_pipe_clk: pcie30_phy3_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <250000000>;
> + #clock-cells = <0>;
> + };
Why PIPE clocks are modeled as fixed clocks unlike other SoCs?
> +
> sleep_clk: sleep-clk {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> };
>
> + usb3phy_0_cc_pipe_clk: usb3phy_0_cc_pipe_clk {
> + compatible = "fixed-clock";
> + clock-frequency = <125000000>;
> + #clock-cells = <0>;
> + };
Spurious?
> +
> xo_board_clk: xo-board-clk {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> @@ -121,6 +151,155 @@
> #size-cells = <1>;
> ranges = <0 0 0 0xffffffff>;
>
> + pcie0_phy: phy at 84000 {
> + compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
> + reg = <0x00084000 0x1bc>; /* Serdes PLL */
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> + clocks = <&gcc GCC_PCIE0_AUX_CLK>,
> + <&gcc GCC_PCIE0_AHB_CLK>,
> + <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
> + <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>;
> + clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
Care to explain what these anoc_lane and snoc_lane clocks are?
> +
> + assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE0_PHY_BCR>,
> + <&gcc GCC_PCIE0PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + status = "disabled";
> +
> + pcie0_lane: phy at 84200 {
> + reg = <0x00084200 0x16c>, /* Serdes Tx */
> + <0x00084400 0x200>, /* Serdes Rx */
> + <0x00084800 0x1f0>, /* PCS: Lane0, COM, PCIE */
> + <0x00084c00 0xf4>; /* pcs_misc */
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "gcc_pcie0_pipe_clk_src";
> + #clock-cells = <0>;
> + };
> + };
> +
[...]
> + pcie1_x1: pci at 10000000 {
> + compatible = "qcom,pcie-ipq9574";
> + reg = <0x10000000 0xf1d>,
> + <0x10000F20 0xa8>,
> + <0x10001000 0x1000>,
> + <0x000F8000 0x4000>,
> + <0x10100000 0x1000>,
> + <0x00618108 0x4>;
> + reg-names = "dbi", "elbi", "atu", "parf", "config", "aggr_noc";
As I asked in the binding patch, why "aggr_noc" region is required?
> + device_type = "pci";
> + linux,pci-domain = <2>;
> + bus-range = <0x00 0xff>;
> + num-lanes = <1>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + ranges = <0x81000000 0 0x10200000 0x10200000
> + 0 0x00100000 /* downstream I/O */
> + 0x82000000 0 0x10300000 0x10300000
> + 0 0x07d00000>; /* non-prefetchable memory */
Don't split the ranges and encode them in a single line.
Also, the I'm not sure why you have set the relocatable flag (n) for both
ranges i.e., in 0x81000000 and 0x82000000.
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 35
> + IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> + <0 0 0 2 &intc 0 49
> + IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> + <0 0 0 3 &intc 0 84
> + IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> + <0 0 0 4 &intc 0 85
> + IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
Again, wrap the interrupts in a single line.
> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "global_irq";
> +
Linux doesn't support global_irq yet. But since devicetree is supposed to
describe the hardware, you can keep it.
Above comment applies to rest of the PCIe nodes.
> + /* clocks and clock-names are used to enable the clock in CBCR */
> + clocks = <&gcc GCC_PCIE1_AHB_CLK>,
> + <&gcc GCC_PCIE1_AUX_CLK>,
> + <&gcc GCC_PCIE1_AXI_M_CLK>,
> + <&gcc GCC_PCIE1_AXI_S_CLK>,
> + <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
> + <&gcc GCC_PCIE1_RCHNG_CLK>;
> + clock-names = "ahb",
> + "aux",
> + "axi_m",
> + "axi_s",
> + "axi_bridge",
> + "rchng";
> +
> + resets = <&gcc GCC_PCIE1_PIPE_ARES>,
> + <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
> + <&gcc GCC_PCIE1_AXI_S_STICKY_ARES>,
> + <&gcc GCC_PCIE1_AXI_S_ARES>,
> + <&gcc GCC_PCIE1_AXI_M_STICKY_ARES>,
> + <&gcc GCC_PCIE1_AXI_M_ARES>,
> + <&gcc GCC_PCIE1_AUX_ARES>,
> + <&gcc GCC_PCIE1_AHB_ARES>;
> + reset-names = "pipe",
> + "sticky",
> + "axi_s_sticky",
> + "axi_s",
> + "axi_m_sticky",
> + "axi_m",
> + "aux",
> + "ahb";
> +
> + phys = <&pcie1_lane>;
> + phy-names = "pciephy";
> + msi-parent = <&v2m0>;
> + status = "disabled";
> + };
> +
[...]
> + pcie2_x2: pci at 20000000 {
> + compatible = "qcom,pcie-ipq9574";
> + reg = <0x20000000 0xf1d>,
> + <0x20000F20 0xa8>,
> + <0x20001000 0x1000>,
> + <0x00088000 0x4000>,
> + <0x20100000 0x1000>;
> + reg-names = "dbi", "elbi", "atu", "parf", "config";
> + device_type = "pci";
> + linux,pci-domain = <3>;
> + bus-range = <0x00 0xff>;
> + num-lanes =<2>;
Space after =
Thanks,
Mani
--
மணிவண்ணன் சதாசிவம்
More information about the linux-phy
mailing list