[PATCH 06/10] phy: qcom: ipq5332: Add support for g3x1 and g3x2 PCIe PHYs

[Praveenkumar I]

On 12/14/2023 12:42 PM, Dmitry Baryshkov wrote:
> On Thu, 14 Dec 2023 at 08:30, Praveenkumar I <quic_ipkumar at quicinc.com> wrote:
>> Add support for single-lane and dual-lane PCIe UNIPHY found on
>> Qualcomm IPQ5332 platform. This UNIPHY is similar to the one
>> present in Qualcomm IPQ5018.
>>
>> Signed-off-by: Praveenkumar I <quic_ipkumar at quicinc.com>
>> ---
>> This patch depends on the below series which adds PCIe support in
>> Qualcomm IPQ5018
>> https://lore.kernel.org/all/20231003120846.28626-1-quic_nsekar@quicinc.com/
>>
>>   .../phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c  | 44 +++++++++++++++++++
>>   1 file changed, 44 insertions(+)
>>
>> diff --git a/drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c b/drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c
>> index 9f9a03faf6fa..aa71b85eb50e 100644
>> --- a/drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c
>> +++ b/drivers/phy/qualcomm/phy-qcom-uniphy-pcie-28lp.c
>> @@ -34,6 +34,10 @@
>>   #define SSCG_CTRL_REG_6                0xb0
>>   #define PCS_INTERNAL_CONTROL_2 0x2d8
>>
>> +#define PHY_CFG_PLLCFG                         0x220
>> +#define PHY_CFG_EIOS_DTCT_REG                  0x3e4
>> +#define PHY_CFG_GEN3_ALIGN_HOLDOFF_TIME                0x3e8
>> +
>>   #define PHY_MODE_FIXED         0x1
>>
>>   enum qcom_uniphy_pcie_type {
>> @@ -112,6 +116,21 @@ static const struct uniphy_regs ipq5018_regs[] = {
>>          },
>>   };
>>
>> +static const struct uniphy_regs ipq5332_regs[] = {
>> +       {
>> +               .offset = PHY_CFG_PLLCFG,
>> +               .val = 0x30,
>> +       },
>> +       {
>> +               .offset = PHY_CFG_EIOS_DTCT_REG,
>> +               .val = 0x53ef,
>> +       },
>> +       {
>> +               .offset = PHY_CFG_GEN3_ALIGN_HOLDOFF_TIME,
>> +               .val = 0xCf,
>> +       },
>> +};
>> +
>>   static const struct uniphy_pcie_data ipq5018_2x2_data = {
>>          .lanes          = 2,
>>          .lane_offset    = 0x800,
>> @@ -121,6 +140,23 @@ static const struct uniphy_pcie_data ipq5018_2x2_data = {
>>          .pipe_clk_rate  = 125000000,
>>   };
>>
>> +static const struct uniphy_pcie_data ipq5332_x2_data = {
>> +       .lanes          = 2,
>> +       .lane_offset    = 0x800,
>> +       .phy_type       = PHY_TYPE_PCIE_GEN3,
>> +       .init_seq       = ipq5332_regs,
>> +       .init_seq_num   = ARRAY_SIZE(ipq5332_regs),
>> +       .pipe_clk_rate  = 250000000,
>> +};
>> +
>> +static const struct uniphy_pcie_data ipq5332_x1_data = {
>> +       .lanes          = 1,
>> +       .phy_type       = PHY_TYPE_PCIE_GEN3,
>> +       .init_seq       = ipq5332_regs,
>> +       .init_seq_num   = ARRAY_SIZE(ipq5332_regs),
>> +       .pipe_clk_rate  = 250000000,
>> +};
> Please keep structs sorted out.
sure, will address in next patch set.
>
>> +
>>   static void qcom_uniphy_pcie_init(struct qcom_uniphy_pcie *phy)
>>   {
>>          const struct uniphy_pcie_data *data = phy->data;
>> @@ -270,6 +306,14 @@ static const struct of_device_id qcom_uniphy_pcie_id_table[] = {
>>                  .compatible = "qcom,ipq5018-uniphy-pcie-gen2x2",
>>                  .data = &ipq5018_2x2_data,
>>          },
>> +       {
>> +               .compatible = "qcom,ipq5332-uniphy-pcie-gen3x2",
>> +               .data = &ipq5332_x2_data,
>> +       },
>> +       {
>> +               .compatible = "qcom,ipq5332-uniphy-pcie-gen3x1",
>> +               .data = &ipq5332_x1_data,
> The entries here should be sorted out.
will take care.
>
>> +       },
>>          { /* Sentinel */ },
>>   };
>>   MODULE_DEVICE_TABLE(of, qcom_uniphy_pcie_id_table);
>> --
>> 2.34.1
>>
>>
>
--
Thanks,
Praveenkumar