[PATCH 6/7] phy: qcom-qusb2: Use dev_err_probe() to simplify code

[Neil Armstrong]

On 22/09/2022 13:12, Yuan Can wrote:
> In the probe path, dev_err() can be replaced with dev_err_probe()
> which will check if error code is -EPROBE_DEFER and prints the
> error name. It also sets the defer probe reason which can be
> checked later through debugfs.
> 
> Signed-off-by: Yuan Can <yuancan at huawei.com>
> ---
>   drivers/phy/qualcomm/phy-qcom-qusb2.c | 27 +++++++++------------------
>   1 file changed, 9 insertions(+), 18 deletions(-)
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
> index 7529a7e6e5df..2ef638b32e8f 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qusb2.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c
> @@ -973,20 +973,14 @@ static int qusb2_phy_probe(struct platform_device *pdev)
>   		return PTR_ERR(qphy->base);
>   
>   	qphy->cfg_ahb_clk = devm_clk_get(dev, "cfg_ahb");
> -	if (IS_ERR(qphy->cfg_ahb_clk)) {
> -		ret = PTR_ERR(qphy->cfg_ahb_clk);
> -		if (ret != -EPROBE_DEFER)
> -			dev_err(dev, "failed to get cfg ahb clk, %d\n", ret);
> -		return ret;
> -	}
> +	if (IS_ERR(qphy->cfg_ahb_clk))
> +		return dev_err_probe(dev, PTR_ERR(qphy->cfg_ahb_clk),
> +				     "failed to get cfg ahb clk\n");
>   
>   	qphy->ref_clk = devm_clk_get(dev, "ref");
> -	if (IS_ERR(qphy->ref_clk)) {
> -		ret = PTR_ERR(qphy->ref_clk);
> -		if (ret != -EPROBE_DEFER)
> -			dev_err(dev, "failed to get ref clk, %d\n", ret);
> -		return ret;
> -	}
> +	if (IS_ERR(qphy->ref_clk))
> +		return dev_err_probe(dev, PTR_ERR(qphy->ref_clk),
> +				     "failed to get ref clk\n");
>   
>   	qphy->iface_clk = devm_clk_get_optional(dev, "iface");
>   	if (IS_ERR(qphy->iface_clk))
> @@ -1003,12 +997,9 @@ static int qusb2_phy_probe(struct platform_device *pdev)
>   		qphy->vregs[i].supply = qusb2_phy_vreg_names[i];
>   
>   	ret = devm_regulator_bulk_get(dev, num, qphy->vregs);
> -	if (ret) {
> -		if (ret != -EPROBE_DEFER)
> -			dev_err(dev, "failed to get regulator supplies: %d\n",
> -				ret);
> -		return ret;
> -	}
> +	if (ret)
> +		return dev_err_probe(dev, ret,
> +				     "failed to get regulator supplies\n");
>   
>   	/* Get the specific init parameters of QMP phy */
>   	qphy->cfg = of_device_get_match_data(dev);


The error handling of devm_reset_control_get_by_index() could probably
be replaced with dev_err_probe() aswell.

Anyway:
Reviewed-by: Neil Armstrong <neil.armstrong at linaro.org>