[PATCH 02/14] dt-bindings: phy: qcom,qmp-usb3-dp: fix sc8280xp bindings

[Rob Herring]

On Fri, 11 Nov 2022 10:24:45 +0100, Johan Hovold wrote:
> The current QMP USB3-DP PHY bindings are based on the original MSM8996
> binding which provided multiple PHYs per IP block and these in turn were
> described by child nodes.
> 
> The QMP USB3-DP PHY block provides a single multi-protocol PHY and even
> if some resources are only used by either the USB or DP part of the
> device there is no real benefit in describing these resources in child
> nodes.
> 
> The original MSM8996 binding also ended up describing the individual
> register blocks as belonging to either the wrapper node or the PHY child
> nodes.
> 
> This is an unnecessary level of detail which has lead to problems when
> later IP blocks using different register layouts have been forced to fit
> the original mould rather than updating the binding. The bindings are
> arguable also incomplete as they only the describe register blocks used
> by the current Linux drivers (e.g. does not include the PCS LANE
> registers).
> 
> This is specifically true for later USB4-USB3-DP QMP PHYs where the TX
> registers are used by both the USB3 and DP parts of the PHY (and where
> the USB4 part of the PHY was not covered by the binding at all). Notably
> there are also no DP "RX" (sic) registers as described by the current
> bindings and the DP "PCS" region is really a set of DP_PHY registers.
> 
> Add a new binding for the USB4-USB3-DP QMP PHYs found on SC8280XP which
> further bindings can be based on.
> 
> Note that the binding uses a PHY type index to access either the USB3 or
> DP part of the PHY and that this can later be used also for the USB4
> part if needed.
> 
> Similarly, the clock inputs and outputs can later be extended to support
> USB4.
> 
> Also note that the current binding is simply removed instead of being
> deprecated as it was only recently merged and would not allow for
> supporting DP mode.
> 
> Signed-off-by: Johan Hovold <johan+linaro at kernel.org>
> ---
>  .../phy/qcom,sc7180-qmp-usb3-dp-phy.yaml      |  12 --
>  .../phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml    | 111 ++++++++++++++++++
>  2 files changed, 111 insertions(+), 12 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:
./Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml:16:11: [error] syntax error: mapping values are not allowed here (syntax)

dtschema/dtc warnings/errors:
make[1]: *** Deleting file 'Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.example.dts'
Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml:16:11: mapping values are not allowed here
make[1]: *** [Documentation/devicetree/bindings/Makefile:26: Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.example.dts] Error 1
make[1]: *** Waiting for unfinished jobs....
./Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml:16:11: mapping values are not allowed here
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml: ignoring, error parsing file
make: *** [Makefile:1492: dt_binding_check] Error 2

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.