[PATCH net-next v2 00/35] [RFT] net: dpaa: Convert to phylink
Sean Anderson
sean.anderson at seco.com
Tue Jun 28 15:13:29 PDT 2022
This series converts the DPAA driver to phylink. Additionally,
it also adds a serdes driver to allow for dynamic reconfiguration
between 1g and 10g interfaces (such as in an SFP+ slot). These changes
are submitted together for this RFC, but they will eventually be
submitted separately to the appropriate subsystem maintainers.
I have tried to maintain backwards compatibility with existing device
trees whereever possible. However, one area where I was unable to
achieve this was with QSGMII. Please refer to patch 3 for details.
All mac drivers have now been converted. I would greatly appreciate if
anyone has QorIQ boards they can test/debug this series on. I only have an
LS1046ARDB. Everything but QSGMII should work without breakage; QSGMII
needs patch 33.
The serdes driver is mostly functional (but not quite, see patches 5 and
31). This series only adds support for the LS1046ARDB SerDes, but it
should be fairly straightforward to add support for other SoCs and
boards (see Documentation/driver-api/phy/qoriq.rst). Patches 34 and 25
should show the typical steps.
This patches in this series can be logically categorized as follows:
- 1, 4, 29, 34-35: SerDes support
- 2, 5-25: Cleanups. These can be applied as-is.
- 3, 26-28, 30-33: Phylink conversion
Patches 5-9 were first submitted as [1].
[1] https://lore.kernel.org/netdev/20220531195851.1592220-1-sean.anderson@seco.com/
Changes in v2:
- Add #clock-cells. This will allow using assigned-clocks* to configure
the PLLs.
- Add CGR update function
- Add helper for sanity checking cgr ops
- Add nodes for QSGMII PCSs
- Add rgmii property to all DPAA MACs
- Adjust queue depth on rate change
- Allow a value of 1 for phy-cells. This allows for compatibility with
the similar (but according to Ioana Ciornei different enough) lynx-28g
binding.
- Better document how we select which PCS to use in the default case
- Clear SGMIIaCR1_PCS_EN during probe
- Configure the SerDes in enable/disable
- Convert 10GEC and dTSEC as well
- Convert FMan MAC bindings to yaml
- Disable SerDes by default to prevent breaking boards inadvertently.
- Document phy cells in the description
- Document the structure of the compatible strings
- Fix capitalization of mEMAC in commit messages
- Fix example binding having too many cells in regs
- Fix not clearing group->pll after disabling it
- Fix prototype for dtsec_initialization
- Fix warning if sizeof(void *) != sizeof(resource_size_t)
- Handle 1000Base-KX in lynx_proto_mode_prep
- Move PCS_LYNX dependency to fman Kconfig
- Move compatible first
- Power off lanes during probe
- Properly implement all ethtool ops and ioctls. These were mostly
stubbed out just enough to compile last time.
- Refer to the device in the documentation, rather than the binding
- Remove minItems
- Remove some unused variables
- Remove unused variable slow_10g_if
- Rename LYNX_PROTO_UNKNOWN to LYNX_PROTO_NONE
- Rename driver to Lynx 10G (etc.)
- Rename to fsl,lynx-10g.yaml
- Restrict valid link modes based on the phy interface. This is easier
to set up, and mostly captures what I intended to do the first time.
We now have a custom validate which restricts half-duplex for some SoCs
for RGMII, but generally just uses the default phylink validate.
- Specify type of mac_dev for exception_cb
- Support 1 and 2 phy-cells
- Use list for clock-names
- Use one phy cell for SerDes1, since no lanes can be grouped
Sean Anderson (35):
dt-bindings: phy: Add QorIQ SerDes binding
dt-bindings: net: Convert FMan MAC bindings to yaml
dt-bindings: net: fman: Add additional interface properties
[RFC] phy: fsl: Add Lynx 10G SerDes driver
net: fman: Convert to SPDX identifiers
net: fman: Don't pass comm_mode to enable/disable
net: fman: Store en/disable in mac_device instead of mac_priv_s
net: fman: dtsec: Always gracefully stop/start
net: fman: Get PCS node in per-mac init
net: fman: Store initialization function in match data
net: fman: Move struct dev to mac_device
net: fman: Configure fixed link in memac_initialization
net: fman: Export/rename some common functions
net: fman: memac: Use params instead of priv for max_speed
net: fman: Move initialization to mac-specific files
net: fman: Mark mac methods static
net: fman: Inline several functions into initialization
net: fman: Remove internal_phy_node from params
net: fman: Map the base address once
net: fman: Pass params directly to mac init
net: fman: Use mac_dev for some params
net: fman: Specify type of mac_dev for exception_cb
net: fman: Clean up error handling
net: fman: Change return type of disable to void
net: dpaa: Use mac_dev variable in dpaa_netdev_init
soc: fsl: qbman: Add helper for sanity checking cgr ops
soc: fsl: qbman: Add CGR update function
net: dpaa: Adjust queue depth on rate change
net: fman: memac: Add serdes support
net: fman: memac: Use lynx pcs driver
[RFT] net: dpaa: Convert to phylink
qoriq: Specify which MACs support RGMII
qoriq: Add nodes for QSGMII PCSs
arm64: dts: ls1046a: Add serdes bindings
arm64: dts: ls1046ardb: Add serdes bindings
.../bindings/net/fsl,fman-dtsec.yaml | 188 +++
.../devicetree/bindings/net/fsl-fman.txt | 133 +-
.../devicetree/bindings/phy/fsl,lynx-10g.yaml | 93 ++
Documentation/driver-api/phy/index.rst | 1 +
Documentation/driver-api/phy/qoriq.rst | 93 ++
MAINTAINERS | 6 +
.../boot/dts/freescale/fsl-ls1043-post.dtsi | 28 +
.../boot/dts/freescale/fsl-ls1046-post.dtsi | 33 +
.../boot/dts/freescale/fsl-ls1046a-rdb.dts | 34 +
.../arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 16 +
arch/powerpc/boot/dts/fsl/b4860si-post.dtsi | 4 +
arch/powerpc/boot/dts/fsl/b4si-post.dtsi | 4 +
.../fsl/qoriq-fman3-0-10g-0-best-effort.dtsi | 3 +-
.../boot/dts/fsl/qoriq-fman3-0-10g-0.dtsi | 9 +-
.../fsl/qoriq-fman3-0-10g-1-best-effort.dtsi | 9 +-
.../boot/dts/fsl/qoriq-fman3-0-10g-1.dtsi | 9 +-
.../boot/dts/fsl/qoriq-fman3-0-1g-0.dtsi | 3 +-
.../boot/dts/fsl/qoriq-fman3-0-1g-1.dtsi | 9 +-
.../boot/dts/fsl/qoriq-fman3-0-1g-2.dtsi | 9 +-
.../boot/dts/fsl/qoriq-fman3-0-1g-3.dtsi | 9 +-
.../boot/dts/fsl/qoriq-fman3-0-1g-4.dtsi | 3 +-
.../boot/dts/fsl/qoriq-fman3-0-1g-5.dtsi | 9 +-
.../boot/dts/fsl/qoriq-fman3-1-10g-0.dtsi | 9 +-
.../boot/dts/fsl/qoriq-fman3-1-10g-1.dtsi | 9 +-
.../boot/dts/fsl/qoriq-fman3-1-1g-0.dtsi | 3 +-
.../boot/dts/fsl/qoriq-fman3-1-1g-1.dtsi | 9 +-
.../boot/dts/fsl/qoriq-fman3-1-1g-2.dtsi | 9 +-
.../boot/dts/fsl/qoriq-fman3-1-1g-3.dtsi | 9 +-
.../boot/dts/fsl/qoriq-fman3-1-1g-4.dtsi | 3 +-
.../boot/dts/fsl/qoriq-fman3-1-1g-5.dtsi | 9 +-
arch/powerpc/boot/dts/fsl/t1023si-post.dtsi | 4 +
arch/powerpc/boot/dts/fsl/t1040si-post.dtsi | 7 +
arch/powerpc/boot/dts/fsl/t2081si-post.dtsi | 8 +
arch/powerpc/boot/dts/fsl/t4240si-post.dtsi | 16 +
drivers/net/ethernet/freescale/dpaa/Kconfig | 4 +-
.../net/ethernet/freescale/dpaa/dpaa_eth.c | 132 +-
.../ethernet/freescale/dpaa/dpaa_eth_sysfs.c | 2 +-
.../ethernet/freescale/dpaa/dpaa_ethtool.c | 90 +-
drivers/net/ethernet/freescale/fman/Kconfig | 3 +-
drivers/net/ethernet/freescale/fman/fman.c | 31 +-
drivers/net/ethernet/freescale/fman/fman.h | 31 +-
.../net/ethernet/freescale/fman/fman_dtsec.c | 670 ++++----
.../net/ethernet/freescale/fman/fman_dtsec.h | 58 +-
.../net/ethernet/freescale/fman/fman_keygen.c | 29 +-
.../net/ethernet/freescale/fman/fman_keygen.h | 29 +-
.../net/ethernet/freescale/fman/fman_mac.h | 34 +-
.../net/ethernet/freescale/fman/fman_memac.c | 877 +++++-----
.../net/ethernet/freescale/fman/fman_memac.h | 57 +-
.../net/ethernet/freescale/fman/fman_muram.c | 31 +-
.../net/ethernet/freescale/fman/fman_muram.h | 32 +-
.../net/ethernet/freescale/fman/fman_port.c | 29 +-
.../net/ethernet/freescale/fman/fman_port.h | 29 +-
drivers/net/ethernet/freescale/fman/fman_sp.c | 29 +-
drivers/net/ethernet/freescale/fman/fman_sp.h | 28 +-
.../net/ethernet/freescale/fman/fman_tgec.c | 274 ++-
.../net/ethernet/freescale/fman/fman_tgec.h | 54 +-
drivers/net/ethernet/freescale/fman/mac.c | 653 +-------
drivers/net/ethernet/freescale/fman/mac.h | 66 +-
drivers/phy/freescale/Kconfig | 20 +
drivers/phy/freescale/Makefile | 1 +
drivers/phy/freescale/phy-fsl-lynx-10g.c | 1483 +++++++++++++++++
drivers/soc/fsl/qbman/qman.c | 76 +-
include/soc/fsl/qman.h | 9 +
63 files changed, 3330 insertions(+), 2331 deletions(-)
create mode 100644 Documentation/devicetree/bindings/net/fsl,fman-dtsec.yaml
create mode 100644 Documentation/devicetree/bindings/phy/fsl,lynx-10g.yaml
create mode 100644 Documentation/driver-api/phy/qoriq.rst
create mode 100644 drivers/phy/freescale/phy-fsl-lynx-10g.c
--
2.35.1.1320.gc452695387.dirty
More information about the linux-phy
mailing list