[PATCH v1 21/30] phy: qcom-qmp-pcie-msm8996: cleanup the driver
Dmitry Baryshkov
dmitry.baryshkov at linaro.org
Tue Jun 7 14:31:54 PDT 2022
Remove the conditionals and options that are not used by the MSM8996
PCIe PHY device. Hardcode has_lane_rst and has_phy_com_ctrl as this is
the case for this PHY.
Acked-by: Bjorn Andersson <bjorn.andersson at linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson at linaro.org> # UFS, PCIe and USB on SC8180X
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
---
.../phy/qualcomm/phy-qcom-qmp-pcie-msm8996.c | 268 +++---------------
1 file changed, 41 insertions(+), 227 deletions(-)
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie-msm8996.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie-msm8996.c
index 02e5ae7fa213..51da3a3a199e 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie-msm8996.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie-msm8996.c
@@ -266,22 +266,6 @@ struct qmp_phy_cfg {
const struct qmp_phy_init_tbl *pcs_misc_tbl_sec;
int pcs_misc_tbl_num_sec;
- /* Init sequence for DP PHY block link rates */
- const struct qmp_phy_init_tbl *serdes_tbl_rbr;
- int serdes_tbl_rbr_num;
- const struct qmp_phy_init_tbl *serdes_tbl_hbr;
- int serdes_tbl_hbr_num;
- const struct qmp_phy_init_tbl *serdes_tbl_hbr2;
- int serdes_tbl_hbr2_num;
- const struct qmp_phy_init_tbl *serdes_tbl_hbr3;
- int serdes_tbl_hbr3_num;
-
- /* DP PHY callbacks */
- int (*configure_dp_phy)(struct qmp_phy *qphy);
- void (*configure_dp_tx)(struct qmp_phy *qphy);
- int (*calibrate_dp_phy)(struct qmp_phy *qphy);
- void (*dp_aux_init)(struct qmp_phy *qphy);
-
/* clock ids to be requested */
const char * const *clk_list;
int num_clks;
@@ -301,28 +285,11 @@ struct qmp_phy_cfg {
/* bit offset of PHYSTATUS in QPHY_PCS_STATUS register */
unsigned int phy_status;
- /* true, if PHY has a separate PHY_COM control block */
- bool has_phy_com_ctrl;
- /* true, if PHY has a reset for individual lanes */
- bool has_lane_rst;
/* true, if PHY needs delay after POWER_DOWN */
bool has_pwrdn_delay;
/* power_down delay in usec */
int pwrdn_delay_min;
int pwrdn_delay_max;
-
- /* true, if PHY has a separate DP_COM control block */
- bool has_phy_dp_com_ctrl;
- /* true, if PHY has secondary tx/rx lanes to be configured */
- bool is_dual_lane_phy;
-
- /* true, if PCS block has no separate SW_RESET register */
- bool no_pcs_sw_reset;
-};
-
-struct qmp_phy_combo_cfg {
- const struct qmp_phy_cfg *usb_cfg;
- const struct qmp_phy_cfg *dp_cfg;
};
/**
@@ -334,17 +301,12 @@ struct qmp_phy_combo_cfg {
* @tx: iomapped memory space for lane's tx
* @rx: iomapped memory space for lane's rx
* @pcs: iomapped memory space for lane's pcs
- * @tx2: iomapped memory space for second lane's tx (in dual lane PHYs)
- * @rx2: iomapped memory space for second lane's rx (in dual lane PHYs)
* @pcs_misc: iomapped memory space for lane's pcs_misc
* @pipe_clk: pipe clock
* @index: lane index
* @qmp: QMP phy to which this lane belongs
* @lane_rst: lane's reset controller
* @mode: current PHY mode
- * @dp_aux_cfg: Display port aux config
- * @dp_opts: Display port optional config
- * @dp_clks: Display port clocks
*/
struct qmp_phy {
struct phy *phy;
@@ -353,30 +315,18 @@ struct qmp_phy {
void __iomem *tx;
void __iomem *rx;
void __iomem *pcs;
- void __iomem *tx2;
- void __iomem *rx2;
void __iomem *pcs_misc;
struct clk *pipe_clk;
unsigned int index;
struct qcom_qmp *qmp;
struct reset_control *lane_rst;
enum phy_mode mode;
- unsigned int dp_aux_cfg;
- struct phy_configure_opts_dp dp_opts;
- struct qmp_phy_dp_clks *dp_clks;
-};
-
-struct qmp_phy_dp_clks {
- struct qmp_phy *qphy;
- struct clk_hw dp_link_hw;
- struct clk_hw dp_pixel_hw;
};
/**
* struct qcom_qmp - structure holding QMP phy block attributes
*
* @dev: device
- * @dp_com: iomapped memory space for phy's dp_com control block
*
* @clks: array of clocks required by phy
* @resets: array of resets required by phy
@@ -385,11 +335,9 @@ struct qmp_phy_dp_clks {
* @phys: array of per-lane phy descriptors
* @phy_mutex: mutex lock for PHY common block initialization
* @init_count: phy common block initialization count
- * @ufs_reset: optional UFS PHY reset handle
*/
struct qcom_qmp {
struct device *dev;
- void __iomem *dp_com;
struct clk_bulk_data *clks;
struct reset_control **resets;
@@ -399,8 +347,6 @@ struct qcom_qmp {
struct mutex phy_mutex;
int init_count;
-
- struct reset_control *ufs_reset;
};
static inline void qphy_setbits(void __iomem *base, u32 offset, u32 val)
@@ -467,8 +413,6 @@ static const struct qmp_phy_cfg msm8996_pciephy_cfg = {
.mask_com_pcs_ready = PCS_READY,
.phy_status = PHYSTATUS,
- .has_phy_com_ctrl = true,
- .has_lane_rst = true,
.has_pwrdn_delay = true,
.pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
.pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
@@ -512,6 +456,8 @@ static int qcom_qmp_phy_pcie_msm8996_serdes_init(struct qmp_phy *qphy)
void __iomem *serdes = qphy->serdes;
const struct qmp_phy_init_tbl *serdes_tbl = cfg->serdes_tbl;
int serdes_tbl_num = cfg->serdes_tbl_num;
+ void __iomem *status;
+ unsigned int mask, val;
int ret;
qcom_qmp_phy_pcie_msm8996_configure(serdes, cfg->regs, serdes_tbl, serdes_tbl_num);
@@ -519,24 +465,20 @@ static int qcom_qmp_phy_pcie_msm8996_serdes_init(struct qmp_phy *qphy)
qcom_qmp_phy_pcie_msm8996_configure(serdes, cfg->regs, cfg->serdes_tbl_sec,
cfg->serdes_tbl_num_sec);
- if (cfg->has_phy_com_ctrl) {
- void __iomem *status;
- unsigned int mask, val;
- qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET], SW_RESET);
- qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
- SERDES_START | PCS_START);
+ qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET], SW_RESET);
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
+ SERDES_START | PCS_START);
- status = serdes + cfg->regs[QPHY_COM_PCS_READY_STATUS];
- mask = cfg->mask_com_pcs_ready;
+ status = serdes + cfg->regs[QPHY_COM_PCS_READY_STATUS];
+ mask = cfg->mask_com_pcs_ready;
- ret = readl_poll_timeout(status, val, (val & mask), 10,
- PHY_INIT_COMPLETE_TIMEOUT);
- if (ret) {
- dev_err(qmp->dev,
- "phy common block init timed-out\n");
- return ret;
- }
+ ret = readl_poll_timeout(status, val, (val & mask), 10,
+ PHY_INIT_COMPLETE_TIMEOUT);
+ if (ret) {
+ dev_err(qmp->dev,
+ "phy common block init timed-out\n");
+ return ret;
}
return 0;
@@ -547,8 +489,6 @@ static int qcom_qmp_phy_pcie_msm8996_com_init(struct qmp_phy *qphy)
struct qcom_qmp *qmp = qphy->qmp;
const struct qmp_phy_cfg *cfg = qphy->cfg;
void __iomem *serdes = qphy->serdes;
- void __iomem *pcs = qphy->pcs;
- void __iomem *dp_com = qmp->dp_com;
int ret, i;
mutex_lock(&qmp->phy_mutex);
@@ -586,41 +526,8 @@ static int qcom_qmp_phy_pcie_msm8996_com_init(struct qmp_phy *qphy)
if (ret)
goto err_assert_reset;
- if (cfg->has_phy_dp_com_ctrl) {
- qphy_setbits(dp_com, QPHY_V3_DP_COM_POWER_DOWN_CTRL,
- SW_PWRDN);
- /* override hardware control for reset of qmp phy */
- qphy_setbits(dp_com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
- SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
- SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
-
- /* Default type-c orientation, i.e CC1 */
- qphy_setbits(dp_com, QPHY_V3_DP_COM_TYPEC_CTRL, 0x02);
-
- qphy_setbits(dp_com, QPHY_V3_DP_COM_PHY_MODE_CTRL,
- USB3_MODE | DP_MODE);
-
- /* bring both QMP USB and QMP DP PHYs PCS block out of reset */
- qphy_clrbits(dp_com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
- SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
- SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
-
- qphy_clrbits(dp_com, QPHY_V3_DP_COM_SWI_CTRL, 0x03);
- qphy_clrbits(dp_com, QPHY_V3_DP_COM_SW_RESET, SW_RESET);
- }
-
- if (cfg->has_phy_com_ctrl) {
- qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
- SW_PWRDN);
- } else {
- if (cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL])
- qphy_setbits(pcs,
- cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL],
- cfg->pwrdn_ctrl);
- else
- qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL,
- cfg->pwrdn_ctrl);
- }
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
+ SW_PWRDN);
mutex_unlock(&qmp->phy_mutex);
@@ -650,15 +557,12 @@ static int qcom_qmp_phy_pcie_msm8996_com_exit(struct qmp_phy *qphy)
return 0;
}
- reset_control_assert(qmp->ufs_reset);
- if (cfg->has_phy_com_ctrl) {
- qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
- SERDES_START | PCS_START);
- qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET],
- SW_RESET);
- qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
- SW_PWRDN);
- }
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
+ SERDES_START | PCS_START);
+ qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET],
+ SW_RESET);
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
+ SW_PWRDN);
while (--i >= 0)
reset_control_assert(qmp->resets[i]);
@@ -676,37 +580,9 @@ static int qcom_qmp_phy_pcie_msm8996_init(struct phy *phy)
{
struct qmp_phy *qphy = phy_get_drvdata(phy);
struct qcom_qmp *qmp = qphy->qmp;
- const struct qmp_phy_cfg *cfg = qphy->cfg;
int ret;
dev_vdbg(qmp->dev, "Initializing QMP phy\n");
- if (cfg->no_pcs_sw_reset) {
- /*
- * Get UFS reset, which is delayed until now to avoid a
- * circular dependency where UFS needs its PHY, but the PHY
- * needs this UFS reset.
- */
- if (!qmp->ufs_reset) {
- qmp->ufs_reset =
- devm_reset_control_get_exclusive(qmp->dev,
- "ufsphy");
-
- if (IS_ERR(qmp->ufs_reset)) {
- ret = PTR_ERR(qmp->ufs_reset);
- dev_err(qmp->dev,
- "failed to get UFS reset: %d\n",
- ret);
-
- qmp->ufs_reset = NULL;
- return ret;
- }
- }
-
- ret = reset_control_assert(qmp->ufs_reset);
- if (ret)
- return ret;
- }
-
ret = qcom_qmp_phy_pcie_msm8996_com_init(qphy);
if (ret)
return ret;
@@ -729,13 +605,11 @@ static int qcom_qmp_phy_pcie_msm8996_power_on(struct phy *phy)
qcom_qmp_phy_pcie_msm8996_serdes_init(qphy);
- if (cfg->has_lane_rst) {
- ret = reset_control_deassert(qphy->lane_rst);
- if (ret) {
- dev_err(qmp->dev, "lane%d reset deassert failed\n",
- qphy->index);
- return ret;
- }
+ ret = reset_control_deassert(qphy->lane_rst);
+ if (ret) {
+ dev_err(qmp->dev, "lane%d reset deassert failed\n",
+ qphy->index);
+ return ret;
}
ret = clk_prepare_enable(qphy->pipe_clk);
@@ -751,40 +625,17 @@ static int qcom_qmp_phy_pcie_msm8996_power_on(struct phy *phy)
qcom_qmp_phy_pcie_msm8996_configure_lane(tx, cfg->regs, cfg->tx_tbl_sec,
cfg->tx_tbl_num_sec, 1);
- /* Configuration for other LANE for USB-DP combo PHY */
- if (cfg->is_dual_lane_phy) {
- qcom_qmp_phy_pcie_msm8996_configure_lane(qphy->tx2, cfg->regs,
- cfg->tx_tbl, cfg->tx_tbl_num, 2);
- if (cfg->tx_tbl_sec)
- qcom_qmp_phy_pcie_msm8996_configure_lane(qphy->tx2, cfg->regs,
- cfg->tx_tbl_sec,
- cfg->tx_tbl_num_sec, 2);
- }
-
qcom_qmp_phy_pcie_msm8996_configure_lane(rx, cfg->regs,
cfg->rx_tbl, cfg->rx_tbl_num, 1);
if (cfg->rx_tbl_sec)
qcom_qmp_phy_pcie_msm8996_configure_lane(rx, cfg->regs,
cfg->rx_tbl_sec, cfg->rx_tbl_num_sec, 1);
- if (cfg->is_dual_lane_phy) {
- qcom_qmp_phy_pcie_msm8996_configure_lane(qphy->rx2, cfg->regs,
- cfg->rx_tbl, cfg->rx_tbl_num, 2);
- if (cfg->rx_tbl_sec)
- qcom_qmp_phy_pcie_msm8996_configure_lane(qphy->rx2, cfg->regs,
- cfg->rx_tbl_sec,
- cfg->rx_tbl_num_sec, 2);
- }
-
qcom_qmp_phy_pcie_msm8996_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
if (cfg->pcs_tbl_sec)
qcom_qmp_phy_pcie_msm8996_configure(pcs, cfg->regs, cfg->pcs_tbl_sec,
cfg->pcs_tbl_num_sec);
- ret = reset_control_deassert(qmp->ufs_reset);
- if (ret)
- goto err_disable_pipe_clk;
-
qcom_qmp_phy_pcie_msm8996_configure(pcs_misc, cfg->regs, cfg->pcs_misc_tbl,
cfg->pcs_misc_tbl_num);
if (cfg->pcs_misc_tbl_sec)
@@ -801,8 +652,8 @@ static int qcom_qmp_phy_pcie_msm8996_power_on(struct phy *phy)
usleep_range(cfg->pwrdn_delay_min, cfg->pwrdn_delay_max);
/* Pull PHY out of reset state */
- if (!cfg->no_pcs_sw_reset)
- qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
+ qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
+
/* start SerDes and Phy-Coding-Sublayer */
qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
@@ -822,8 +673,7 @@ static int qcom_qmp_phy_pcie_msm8996_power_on(struct phy *phy)
err_disable_pipe_clk:
clk_disable_unprepare(qphy->pipe_clk);
err_reset_lane:
- if (cfg->has_lane_rst)
- reset_control_assert(qphy->lane_rst);
+ reset_control_assert(qphy->lane_rst);
return ret;
}
@@ -836,8 +686,7 @@ static int qcom_qmp_phy_pcie_msm8996_power_off(struct phy *phy)
clk_disable_unprepare(qphy->pipe_clk);
/* PHY reset */
- if (!cfg->no_pcs_sw_reset)
- qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
+ qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
/* stop SerDes and Phy-Coding-Sublayer */
qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
@@ -857,10 +706,8 @@ static int qcom_qmp_phy_pcie_msm8996_power_off(struct phy *phy)
static int qcom_qmp_phy_pcie_msm8996_exit(struct phy *phy)
{
struct qmp_phy *qphy = phy_get_drvdata(phy);
- const struct qmp_phy_cfg *cfg = qphy->cfg;
- if (cfg->has_lane_rst)
- reset_control_assert(qphy->lane_rst);
+ reset_control_assert(qphy->lane_rst);
qcom_qmp_phy_pcie_msm8996_com_exit(qphy);
@@ -1065,31 +912,7 @@ int qcom_qmp_phy_pcie_msm8996_create(struct device *dev, struct device_node *np,
if (!qphy->pcs)
return -ENOMEM;
- /*
- * If this is a dual-lane PHY, then there should be registers for the
- * second lane. Some old device trees did not specify this, so fall
- * back to old legacy behavior of assuming they can be reached at an
- * offset from the first lane.
- */
- if (cfg->is_dual_lane_phy) {
- qphy->tx2 = of_iomap(np, 3);
- qphy->rx2 = of_iomap(np, 4);
- if (!qphy->tx2 || !qphy->rx2) {
- dev_warn(dev,
- "Underspecified device tree, falling back to legacy register regions\n");
-
- /* In the old version, pcs_misc is at index 3. */
- qphy->pcs_misc = qphy->tx2;
- qphy->tx2 = qphy->tx + QMP_PHY_LEGACY_LANE_STRIDE;
- qphy->rx2 = qphy->rx + QMP_PHY_LEGACY_LANE_STRIDE;
-
- } else {
- qphy->pcs_misc = of_iomap(np, 5);
- }
-
- } else {
- qphy->pcs_misc = of_iomap(np, 3);
- }
+ qphy->pcs_misc = of_iomap(np, 3);
if (!qphy->pcs_misc)
dev_vdbg(dev, "PHY pcs_misc-reg not used\n");
@@ -1117,18 +940,16 @@ int qcom_qmp_phy_pcie_msm8996_create(struct device *dev, struct device_node *np,
}
/* Get lane reset, if any */
- if (cfg->has_lane_rst) {
- snprintf(prop_name, sizeof(prop_name), "lane%d", id);
- qphy->lane_rst = of_reset_control_get_exclusive(np, prop_name);
- if (IS_ERR(qphy->lane_rst)) {
- dev_err(dev, "failed to get lane%d reset\n", id);
- return PTR_ERR(qphy->lane_rst);
- }
- ret = devm_add_action_or_reset(dev, qcom_qmp_reset_control_put,
- qphy->lane_rst);
- if (ret)
- return ret;
+ snprintf(prop_name, sizeof(prop_name), "lane%d", id);
+ qphy->lane_rst = of_reset_control_get_exclusive(np, prop_name);
+ if (IS_ERR(qphy->lane_rst)) {
+ dev_err(dev, "failed to get lane%d reset\n", id);
+ return PTR_ERR(qphy->lane_rst);
}
+ ret = devm_add_action_or_reset(dev, qcom_qmp_reset_control_put,
+ qphy->lane_rst);
+ if (ret)
+ return ret;
generic_phy = devm_phy_create(dev, np, &qcom_qmp_phy_pcie_msm8996_ops);
if (IS_ERR(generic_phy)) {
@@ -1183,13 +1004,6 @@ static int qcom_qmp_phy_pcie_msm8996_probe(struct platform_device *pdev)
if (IS_ERR(serdes))
return PTR_ERR(serdes);
- /* per PHY dp_com; if PHY has dp_com control block */
- if (cfg->has_phy_dp_com_ctrl) {
- qmp->dp_com = devm_platform_ioremap_resource(pdev, 1);
- if (IS_ERR(qmp->dp_com))
- return PTR_ERR(qmp->dp_com);
- }
-
expected_phys = cfg->nlanes;
mutex_init(&qmp->phy_mutex);
--
2.35.1
More information about the linux-phy
mailing list