[PATCH v10 2/3] phy: qcom-snps: Add support for overriding phy tuning parameters
Krishna Kurapati PSSNV
quic_kriskura at quicinc.com
Tue Jul 12 20:31:33 PDT 2022
On 7/5/2022 7:06 PM, Bjorn Andersson wrote:
> On Sun 03 Jul 08:13 CDT 2022, Krishna Kurapati wrote:
>
>> Add support for overriding electrical signal tuning parameters for
>> SNPS HS Phy.
>>
>> Signed-off-by: Krishna Kurapati <quic_kriskura at quicinc.com>
>> Reviewed-by: Pavankumar Kondeti <quic_pkondeti at quicinc.com>
>> ---
>> drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 260 +++++++++++++++++++++++++-
>> 1 file changed, 258 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
>> index 5d20378..a002e90 100644
>> --- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
>> +++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
>> @@ -52,6 +52,12 @@
>> #define USB2_SUSPEND_N BIT(2)
>> #define USB2_SUSPEND_N_SEL BIT(3)
>>
>> +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0 (0x6c)
>> +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1 (0x70)
>> +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2 (0x74)
>> +#define USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X3 (0x78)
>> +#define PARAM_OVRD_MASK 0xFF
>> +
>> #define USB2_PHY_USB_PHY_CFG0 (0x94)
>> #define UTMI_PHY_DATAPATH_CTRL_OVERRIDE_EN BIT(0)
>> #define UTMI_PHY_CMN_CTRL_OVERRIDE_EN BIT(1)
>> @@ -60,12 +66,69 @@
>> #define REFCLK_SEL_MASK GENMASK(1, 0)
>> #define REFCLK_SEL_DEFAULT (0x2 << 0)
>>
>> +#define HS_DISCONNECT_MASK GENMASK(2, 0)
>> +#define SQUELCH_DETECTOR_MASK GENMASK(7, 5)
>> +
>> +#define HS_AMPLITUDE_MASK GENMASK(3, 0)
>> +#define PREEMPHASIS_DURATION_MASK BIT(5)
>> +#define PREEMPHASIS_AMPLITUDE_MASK GENMASK(7, 6)
>> +
>> +#define HS_RISE_FALL_MASK GENMASK(1, 0)
>> +#define HS_CROSSOVER_VOLTAGE_MASK GENMASK(3, 2)
>> +#define HS_OUTPUT_IMPEDANCE_MASK GENMASK(5, 4)
>> +
>> +#define LS_FS_OUTPUT_IMPEDANCE_MASK GENMASK(3, 0)
>> +
>> static const char * const qcom_snps_hsphy_vreg_names[] = {
>> "vdda-pll", "vdda33", "vdda18",
>> };
>>
>> #define SNPS_HS_NUM_VREGS ARRAY_SIZE(qcom_snps_hsphy_vreg_names)
>>
>> +struct override_param {
>> + s32 value;
>> + u8 reg;
>> +};
>> +
>> +#define OVERRIDE_PARAM(bps, val) { \
>> + .value = bps, \
>> + .reg = val, \
>> +}
>> +
>> +struct override_param_map {
>> + const struct override_param *param_table;
>> + u8 table_size;
>> + u8 reg_offset;
>> + u8 param_mask;
>> +};
>> +
>> +#define OVERRIDE_PARAM_MAP(table, num_elements, offset, mask) \
>> +{ \
>> + .param_table = table, \
>> + .table_size = num_elements, \
>> + .reg_offset = offset, \
>> + .param_mask = mask, \
>> +}
>> +
>> +struct phy_override_seq {
>> + bool need_update;
>> + u8 offset;
>> + u8 value;
>> + u8 mask;
>> +};
>> +
>> +static const char * const phy_seq_props[] = {
>> + "qcom,hs-disconnect-bp",
>> + "qcom,squelch-detector-bp",
>> + "qcom,hs-amplitude-bp",
>> + "qcom,pre-emphasis-duration-bp",
>> + "qcom,pre-emphasis-amplitude-bp",
>> + "qcom,hs-rise-fall-time-bp",
>> + "qcom,hs-crossover-voltage-microvolt",
>> + "qcom,hs-output-impedance-micro-ohms",
>> + "qcom,ls-fs-output-impedance-bp",
>> +};
>> +
>> /**
>> * struct qcom_snps_hsphy - snps hs phy attributes
>> *
>> @@ -91,6 +154,7 @@ struct qcom_snps_hsphy {
>>
>> bool phy_initialized;
>> enum phy_mode mode;
>> + struct phy_override_seq update_seq_cfg[ARRAY_SIZE(phy_seq_props)];
>> };
>>
>> static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,
>> @@ -173,10 +237,147 @@ static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode,
>> return 0;
>> }
>>
>> +static const struct override_param hs_disconnect_sc7280[] = {
> Is this mapping unique to sc7280? Will other 7nm implementation of the
> Femto phy use different mappings?
Hi Bjorn,
The values will be same for most of the cases. (Atleast till now, all
devices using this phy,
both upstream and downstream have same register values).
>> + OVERRIDE_PARAM(-272, 0),
>> + OVERRIDE_PARAM(0, 1),
>> + OVERRIDE_PARAM(317, 2),
>> + OVERRIDE_PARAM(630, 3),
>> + OVERRIDE_PARAM(973, 4),
>> + OVERRIDE_PARAM(1332, 5),
>> + OVERRIDE_PARAM(1743, 6),
>> + OVERRIDE_PARAM(2156, 7),
>> +};
>> +
>> +static const struct override_param squelch_det_threshold_sc7280[] = {
>> + OVERRIDE_PARAM(-2090, 7),
>> + OVERRIDE_PARAM(-1560, 6),
>> + OVERRIDE_PARAM(-1030, 5),
>> + OVERRIDE_PARAM(-530, 4),
>> + OVERRIDE_PARAM(0, 3),
>> + OVERRIDE_PARAM(530, 2),
>> + OVERRIDE_PARAM(1060, 1),
>> + OVERRIDE_PARAM(1590, 0),
>> +};
>> +
>> +static const struct override_param hs_amplitude_sc7280[] = {
>> + OVERRIDE_PARAM(-660, 0),
>> + OVERRIDE_PARAM(-440, 1),
>> + OVERRIDE_PARAM(-220, 2),
>> + OVERRIDE_PARAM(0, 3),
>> + OVERRIDE_PARAM(230, 4),
>> + OVERRIDE_PARAM(440, 5),
>> + OVERRIDE_PARAM(650, 6),
>> + OVERRIDE_PARAM(890, 7),
>> + OVERRIDE_PARAM(1110, 8),
>> + OVERRIDE_PARAM(1330, 9),
>> + OVERRIDE_PARAM(1560, 10),
>> + OVERRIDE_PARAM(1780, 11),
>> + OVERRIDE_PARAM(2000, 12),
>> + OVERRIDE_PARAM(2220, 13),
>> + OVERRIDE_PARAM(2430, 14),
>> + OVERRIDE_PARAM(2670, 15),
>> +};
>> +
>> +static const struct override_param preemphasis_duration_sc7280[] = {
>> + OVERRIDE_PARAM(10000, 1),
>> + OVERRIDE_PARAM(20000, 0),
>> +};
>> +
>> +static const struct override_param preemphasis_amplitude_sc7280[] = {
>> + OVERRIDE_PARAM(10000, 1),
>> + OVERRIDE_PARAM(20000, 2),
>> + OVERRIDE_PARAM(30000, 3),
>> + OVERRIDE_PARAM(40000, 0),
>> +};
>> +
>> +static const struct override_param hs_rise_fall_time_sc7280[] = {
>> + OVERRIDE_PARAM(-4100, 3),
>> + OVERRIDE_PARAM(0, 2),
>> + OVERRIDE_PARAM(2810, 1),
>> + OVERRIDE_PARAM(5430, 0),
>> +};
>> +
>> +static const struct override_param hs_crossover_voltage_sc7280[] = {
>> + OVERRIDE_PARAM(-31000, 1),
>> + OVERRIDE_PARAM(0, 3),
>> + OVERRIDE_PARAM(28000, 2),
>> +};
>> +
>> +static const struct override_param hs_output_impedance_sc7280[] = {
>> + OVERRIDE_PARAM(-2300000, 3),
>> + OVERRIDE_PARAM(0, 2),
>> + OVERRIDE_PARAM(2600000, 1),
>> + OVERRIDE_PARAM(6100000, 0),
>> +};
>> +
>> +static const struct override_param ls_fs_output_impedance_sc7280[] = {
>> + OVERRIDE_PARAM(-1053, 15),
>> + OVERRIDE_PARAM(-557, 7),
>> + OVERRIDE_PARAM(0, 3),
>> + OVERRIDE_PARAM(612, 1),
>> + OVERRIDE_PARAM(1310, 0),
>> +};
>> +
>> +static const struct override_param_map sc7280_idp[] = {
> Why does this say "idp", are you expecting a different table for other
> devices on sc7280? As with above, are these tuneables specific to
> sc7280, or do they apply to all 7nm implementations of the Femto? What
> about other incarnations?
I put the suffix as IDP but been using the same for all version of sc7280.
These tuneables are not spec to sc7280. Currently all downstream and
upstream
qcom devices using this phy have the same register mappings.
>> + OVERRIDE_PARAM_MAP(
>> + hs_disconnect_sc7280,
>> + ARRAY_SIZE(hs_disconnect_sc7280),
>> + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0,
>> + HS_DISCONNECT_MASK),
>> +
>> + OVERRIDE_PARAM_MAP(
>> + squelch_det_threshold_sc7280,
>> + ARRAY_SIZE(squelch_det_threshold_sc7280),
>> + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X0,
>> + SQUELCH_DETECTOR_MASK),
>> +
>> + OVERRIDE_PARAM_MAP(
>> + hs_amplitude_sc7280,
>> + ARRAY_SIZE(hs_amplitude_sc7280),
>> + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1,
>> + HS_AMPLITUDE_MASK),
>> +
>> + OVERRIDE_PARAM_MAP(
>> + preemphasis_duration_sc7280,
>> + ARRAY_SIZE(preemphasis_duration_sc7280),
>> + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1,
>> + PREEMPHASIS_DURATION_MASK),
>> +
>> + OVERRIDE_PARAM_MAP(
>> + preemphasis_amplitude_sc7280,
>> + ARRAY_SIZE(preemphasis_amplitude_sc7280),
>> + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X1,
>> + PREEMPHASIS_AMPLITUDE_MASK),
>> +
>> + OVERRIDE_PARAM_MAP(
>> + hs_rise_fall_time_sc7280,
>> + ARRAY_SIZE(hs_rise_fall_time_sc7280),
>> + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2,
>> + HS_RISE_FALL_MASK),
>> +
>> + OVERRIDE_PARAM_MAP(
>> + hs_crossover_voltage_sc7280,
>> + ARRAY_SIZE(hs_crossover_voltage_sc7280),
>> + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2,
>> + HS_CROSSOVER_VOLTAGE_MASK),
>> +
>> + OVERRIDE_PARAM_MAP(
>> + hs_output_impedance_sc7280,
>> + ARRAY_SIZE(hs_output_impedance_sc7280),
>> + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X2,
>> + HS_OUTPUT_IMPEDANCE_MASK),
>> +
>> + OVERRIDE_PARAM_MAP(
>> + ls_fs_output_impedance_sc7280,
>> + ARRAY_SIZE(ls_fs_output_impedance_sc7280),
>> + USB2_PHY_USB_PHY_HS_PHY_OVERRIDE_X3,
>> + LS_FS_OUTPUT_IMPEDANCE_MASK),
>> +};
>> +
>> static int qcom_snps_hsphy_init(struct phy *phy)
>> {
>> struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
>> - int ret;
>> + int ret, i;
>>
>> dev_vdbg(&phy->dev, "%s(): Initializing SNPS HS phy\n", __func__);
>>
>> @@ -223,6 +424,14 @@ static int qcom_snps_hsphy_init(struct phy *phy)
>> qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL1,
>> VBUSVLDEXT0, VBUSVLDEXT0);
>>
>> + for (i = 0; i < ARRAY_SIZE(hsphy->update_seq_cfg); i++) {
>> + if (hsphy->update_seq_cfg[i].need_update)
>> + qcom_snps_hsphy_write_mask(hsphy->base,
>> + hsphy->update_seq_cfg[i].offset,
>> + hsphy->update_seq_cfg[i].mask,
>> + hsphy->update_seq_cfg[i].value);
>> + }
>> +
>> qcom_snps_hsphy_write_mask(hsphy->base,
>> USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON2,
>> VREGBYPASS, VREGBYPASS);
>> @@ -280,7 +489,10 @@ static const struct phy_ops qcom_snps_hsphy_gen_ops = {
>> static const struct of_device_id qcom_snps_hsphy_of_match_table[] = {
>> { .compatible = "qcom,sm8150-usb-hs-phy", },
>> { .compatible = "qcom,usb-snps-hs-5nm-phy", },
>> - { .compatible = "qcom,usb-snps-hs-7nm-phy", },
>> + {
>> + .compatible = "qcom,usb-snps-hs-7nm-phy",
>> + .data = &sc7280_idp,
>> + },
>> { .compatible = "qcom,usb-snps-femto-v2-phy", },
>> { }
>> };
>> @@ -291,6 +503,49 @@ static const struct dev_pm_ops qcom_snps_hsphy_pm_ops = {
>> qcom_snps_hsphy_runtime_resume, NULL)
>> };
>>
>> +static void qcom_snps_hsphy_override_param_update_val(
>> + const struct override_param_map map,
>> + s32 dt_val, struct phy_override_seq *seq_entry)
>> +{
>> + int i;
>> +
>> + /*
>> + * Param table for each param is in increasing order
>> + * of dt values. We need to iterate over the list to
>> + * select the entry that has equal or the next highest value.
>> + */
> When is it useful to have this rounding to the higher value, over just
> doing an exact match with the available register values?
This was just implemented this way just in case some one provided a
values that doesn't
match the register mappings. But if it doesn't make sense to put it this
way, I can do a direct lookup
of register mapping tables.
>
>> + for (i = 0; i < map.table_size - 1; i++) {
>> + if (map.param_table[i].value >= dt_val)
>> + break;
>> + }
>> +
>> + seq_entry->need_update = true;
>> + seq_entry->offset = map.reg_offset;
>> + seq_entry->mask = map.param_mask;
>> + seq_entry->value = map.param_table[i].reg << __ffs(map.param_mask);
>> +}
>> +
>> +static void qcom_snps_hsphy_read_override_param_seq(struct device *dev)
>> +{
>> + struct device_node *node = dev->of_node;
>> + s32 val;
>> + int ret, i;
>> + struct qcom_snps_hsphy *hsphy;
>> + const struct override_param_map *cfg = of_device_get_match_data(dev);
>> +
>> + hsphy = dev_get_drvdata(dev);
> You only call this function from qcom_snps_hsphy_probe(), where you have
> hsphy already. If you pass that as your argument to the function instead
> you don't have to dig it out from the struct device.
Sure, Will do it in the next revision of the patch.
>> +
>> + for (i = 0; i < ARRAY_SIZE(phy_seq_props); i++) {
>> + ret = of_property_read_s32(node, phy_seq_props[i], &val);
>> + if (!ret) {
>> + dev_dbg(&hsphy->phy->dev, "Read param: %s val: %d\n",
>> + phy_seq_props[i], val);
> I think it's fair to assume that the reader of this debug print is
> looking at the register documentation and trying to figure out if they
> are getting the right values in the registers. So it would probably be a
> good idea to include those details in the print.
>
> For that to be useful I think you need to inline
> qcom_snps_hsphy_override_param_update_val() here, but that doesn't seem
> like a bad idea anyways (and turn the conditional above into if (ret)
> continue; to save the indentation level).
>
> Thanks,
> Bjorn
Thanks, Will add details to actual reg values as well in debug logs.
>
>> + qcom_snps_hsphy_override_param_update_val(cfg[i], val,
>> + &hsphy->update_seq_cfg[i]);
>> + }
>> + }
>> +}
>> +
>> static int qcom_snps_hsphy_probe(struct platform_device *pdev)
>> {
>> struct device *dev = &pdev->dev;
>> @@ -352,6 +607,7 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
>>
>> dev_set_drvdata(dev, hsphy);
>> phy_set_drvdata(generic_phy, hsphy);
>> + qcom_snps_hsphy_read_override_param_seq(dev);
>>
>> phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>> if (!IS_ERR(phy_provider))
>> --
>> 2.7.4
>>
More information about the linux-phy
mailing list