[PATCH devicetree v3] dt-bindings: phy: Add `tx-p2p-microvolt` property binding

[Marc Kleine-Budde]

On 20.01.2022 19:01:55, Marek Behún wrote:
> On Thu, 20 Jan 2022 09:49:14 +0100
> Marc Kleine-Budde <mkl at pengutronix.de> wrote:
> 
> > On 19.01.2022 14:11:17, Marek Behún wrote:
> > > Common PHYs and network PCSes often have the possibility to specify
> > > peak-to-peak voltage on the differential pair - the default voltage
> > > sometimes needs to be changed for a particular board.
> > > 
> > > Add properties `tx-p2p-microvolt` and `tx-p2p-microvolt-names` for this
> > > purpose. The second property is needed to specify the mode for the
> > > corresponding voltage in the `tx-p2p-microvolt` property, if the voltage
> > > is to be used only for speficic mode. More voltage-mode pairs can be
> > > specified.
> > > 
> > > Example usage with only one voltage (it will be used for all supported
> > > PHY modes, the `tx-p2p-microvolt-names` property is not needed in this
> > > case):
> > > 
> > >   tx-p2p-microvolt = <915000>;
> > > 
> > > Example usage with voltages for multiple modes:
> > > 
> > >   tx-p2p-microvolt = <915000>, <1100000>, <1200000>;
> > >   tx-p2p-microvolt-names = "2500base-x", "usb", "pcie";
> > > 
> > > Add these properties into a separate file phy/transmit-amplitude.yaml,
> > > which should be referenced by any binding that uses it.  
> > 
> > If I understand your use-case correctly, you need different voltage p2p
> > levels in the connection between the Ethernet MAC and the Ethernet
> > switch or Ethernet-PHY?
> 
> This is a SerDes differential pair amplitude. So yes to your question,
> if the MII interface uses differential pair, like sgmii, 10gbase-r, ...
> 
> > Some of the two wire Ethernet standards (10base-T1S, 10base-T1L,
> > 100base-T1, 1000base-T1) defines several p2p voltage levels on the wire,
> > i.e. between the PHYs. Alexandru has posed a series where you can
> > specify the between-PHY voltage levels:
> > 
> > | https://lore.kernel.org/all/20211210110509.20970-8-alexandru.tachici@analog.com/
> 
> Copper ethernet is something different, so no conflict
> 
> > Can we make clear that your binding specifies the voltage level on the
> > MII interface, in contrast Alexandru's binding?
> 
> The binding explicitly says "common PHY", not ethernet PHY. I don't
> thing there will be any confusion. It can also be specified for USB3+
> differential pairs, or PCIe differential pairs, or DisplayPort
> differential pairs...

Thanks for the clarification.

regards,
Marc

-- 
Pengutronix e.K.                 | Marc Kleine-Budde           |
Embedded Linux                   | https://www.pengutronix.de  |
Vertretung West/Dortmund         | Phone: +49-231-2826-924     |
Amtsgericht Hildesheim, HRA 2686 | Fax:   +49-5121-206917-5555 |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 488 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-phy/attachments/20220120/94ceb650/attachment.sig>