Re: [PATCH v4 09/23] phy: qcom-qmp-ufs: Avoid setting HS G3 specific registers

[Dmitry Baryshkov]

On 1 December 2022 20:43:14 GMT+03:00, Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org> wrote:
>SM8350 default init sequence sets some PCS registers to HS G3, thereby
>disabling HS G4 mode. This has the effect on MPHY capability negotiation
>between the host and the device during link startup and causes the
>PA_MAXHSGEAR to G3 irrespective of device max gear.
>
>Due to that, the agreed gear speed determined by the UFS core will become
>G3 only and the platform won't run at G4.
>
>So, let's remove setting these registers for SM8350 as like other G4
>compatible platforms. One downside of this is that, when the board design
>uses non-G4 compatible device, then MPHY will continue to run in the

QMP PHY?

>default mode (G4) even if UFSHCD runs in G3. But this is the case for
>other platforms as well.

Should this be fixed by adding a separate set of tables used to setup g3?


>
>Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
>---
> drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 7 -------
> 1 file changed, 7 deletions(-)
>
>diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>index d5324c4e8513..6c7c6a06fe3b 100644
>--- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>+++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>@@ -567,13 +567,6 @@ static const struct qmp_phy_init_tbl sm8350_ufsphy_pcs[] = {
> 	QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
> 	QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_DEBUG_BUS_CLKSEL, 0x1f),
> 	QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_RX_MIN_HIBERN8_TIME, 0xff),
>-	QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_PLL_CNTL, 0x03),
>-	QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TIMER_20US_CORECLK_STEPS_MSB, 0x16),
>-	QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TIMER_20US_CORECLK_STEPS_LSB, 0xd8),
>-	QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_PWM_GEAR_BAND, 0xaa),
>-	QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_HS_GEAR_BAND, 0x06),
>-	QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x03),
>-	QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x03),
> 	QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_RX_SIGDET_CTRL1, 0x0e),
> 	QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
> };

-- 
With best wishes
Dmitry