[PATCH v4 5/8] phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver
Tim Harvey
tharvey at gateworks.com
Fri Oct 29 10:44:57 PDT 2021
On Fri, Oct 29, 2021 at 1:45 AM Richard Zhu <hongxing.zhu at nxp.com> wrote:
>
>
> > -----Original Message-----
> > From: Marcel Ziswiler <marcel.ziswiler at toradex.com>
> > Sent: Friday, October 29, 2021 4:13 PM
> > To: kishon at ti.com; vkoul at kernel.org; robh at kernel.org;
> > l.stach at pengutronix.de; shawnguo at kernel.org;
> > tharvey at gateworks.com; galak at kernel.crashing.org; Richard Zhu
> > <hongxing.zhu at nxp.com>
> > Cc: linux-phy at lists.infradead.org; linux-arm-kernel at lists.infradead.org;
> > kernel at pengutronix.de; devicetree at vger.kernel.org;
> > linux-kernel at vger.kernel.org; dl-linux-imx <linux-imx at nxp.com>
> > Subject: Re: [PATCH v4 5/8] phy: freescale: pcie: Initialize the imx8 pcie
> > standalone phy driver
> >
> > On Thu, 2021-10-28 at 15:27 +0800, Richard Zhu wrote:
> > > Add the standalone i.MX8 PCIe PHY driver.
> > >
> > > Signed-off-by: Richard Zhu <hongxing.zhu at nxp.com>
> > > Tested-by: Marcel Ziswiler <marcel.ziswiler at toradex.com>
> >
> > Unfortunately, this version no longer works for our
> > IMX8_PCIE_REFCLK_PAD_OUTPUT use-case. Further comments in- lined
> > below.
> >
> [Richard Zhu] Sorry to hear about that. Then, it seems that this bit should be
> set anyway.
> It's hard to understand this bit refer to the RM document. Sigh ☹.
> Would set the AUX_EN bit later.
>
> > > ---
> > > drivers/phy/freescale/Kconfig | 9 +
> > > drivers/phy/freescale/Makefile | 1 +
> > > drivers/phy/freescale/phy-fsl-imx8m-pcie.c | 234
> > > +++++++++++++++++++++
> > > 3 files changed, 244 insertions(+)
> > > create mode 100644 drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> > >
> > > diff --git a/drivers/phy/freescale/Kconfig
> > > b/drivers/phy/freescale/Kconfig index 320630ffe3cd..de9ee7020f76
> > > 100644
> > > --- a/drivers/phy/freescale/Kconfig
> > > +++ b/drivers/phy/freescale/Kconfig
> > > @@ -14,3 +14,12 @@ config PHY_MIXEL_MIPI_DPHY
> > > help
> > > Enable this to add support for the Mixel DSI PHY as
> > found
> > > on NXP's i.MX8 family of SOCs.
> > > +
> > > +config PHY_FSL_IMX8M_PCIE
> > > + tristate "Freescale i.MX8 PCIE PHY"
> >
> > Above description is missing the M as in i.MX 8M.
> [Richard Zhu] Okay, would be added later.
> Thanks.
>
> >
> > > + depends on OF && HAS_IOMEM
> > > + select GENERIC_PHY
> > > + default ARCH_MXC && ARM64
> > > + help
> > > + Enable this to add support for the PCIE PHY as found on
> > > + i.MX8M family of SOCs.
> > > diff --git a/drivers/phy/freescale/Makefile
> > > b/drivers/phy/freescale/Makefile index 1d02e3869b45..55d07c742ab0
> > > 100644
> > > --- a/drivers/phy/freescale/Makefile
> > > +++ b/drivers/phy/freescale/Makefile
> > > @@ -1,3 +1,4 @@
> > > # SPDX-License-Identifier: GPL-2.0-only
> > > obj-$(CONFIG_PHY_FSL_IMX8MQ_USB) +=
> > phy-fsl-imx8mq-usb.o
> > > obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY) +=
> > phy-fsl-imx8-mipi-dphy.o
> > > +obj-$(CONFIG_PHY_FSL_IMX8M_PCIE) +=
> > phy-fsl-imx8m-pcie.o
> > > diff --git a/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> > > b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> > > new file mode 100644
> > > index 000000000000..4b4402eaddcc
> > > --- /dev/null
> > > +++ b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> > > @@ -0,0 +1,234 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +/*
> > > + * Copyright 2021 NXP
> > > + */
> > > +
> > > +#include <linux/clk.h>
> > > +#include <linux/io.h>
> > > +#include <linux/iopoll.h>
> > > +#include <linux/delay.h>
> > > +#include <linux/mfd/syscon.h>
> > > +#include <linux/mfd/syscon/imx7-iomuxc-gpr.h>
> > > +#include <linux/module.h>
> > > +#include <linux/phy/phy.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/regmap.h>
> > > +#include <linux/reset.h>
> > > +#include <dt-bindings/phy/phy-imx8-pcie.h>
> > > +
> > > +#define IMX8MM_PCIE_PHY_CMN_REG061 0x184 #define
> > > +ANA_PLL_CLK_OUT_TO_EXT_IO_EN BIT(0) #define
> > > +IMX8MM_PCIE_PHY_CMN_REG062 0x188 #define
> > > +ANA_PLL_CLK_OUT_TO_EXT_IO_SEL BIT(3) #define
> > > +IMX8MM_PCIE_PHY_CMN_REG063 0x18C #define
> > > +AUX_PLL_REFCLK_SEL_SYS_PLL GENMASK(7, 6) #define
> > > +IMX8MM_PCIE_PHY_CMN_REG064 0x190
> > #define ANA_AUX_RX_TX_SEL_TX
> > > +BIT(7)
> > #define ANA_AUX_RX_TERM_GND_EN BIT(3)
> > #define
> > > +ANA_AUX_TX_TERM BIT(2) #define
> > > +IMX8MM_PCIE_PHY_CMN_REG065 0x194
> > #define ANA_AUX_RX_TERM
> > > +(BIT(7) | BIT(4))
> > #define ANA_AUX_TX_LVL
> > > +GENMASK(3, 0) #define
> > IMX8MM_PCIE_PHY_CMN_REG75 0x1D4 #define
> > > +PCIE_PHY_CMN_REG75_PLL_DONE 0x3 #define
> > PCIE_PHY_TRSV_REG5
> > > +0x414 #define PCIE_PHY_TRSV_REG5_GEN1_DEEMP 0x2D #define
> > > +PCIE_PHY_TRSV_REG6 0x418 #define
> > > +PCIE_PHY_TRSV_REG6_GEN2_DEEMP 0xF
> > > +
> > > +#define IMX8MM_GPR_PCIE_REF_CLK_SEL GENMASK(25, 24)
> > #define
> > > +IMX8MM_GPR_PCIE_REF_CLK_PLL
> > > +FIELD_PREP(IMX8MM_GPR_PCIE_REF_CLK_SEL, 0x3) #define
> > > +IMX8MM_GPR_PCIE_REF_CLK_EXT
> > > +FIELD_PREP(IMX8MM_GPR_PCIE_REF_CLK_SEL, 0x2) #define
> > > +IMX8MM_GPR_PCIE_AUX_EN BIT(19) #define
> > > +IMX8MM_GPR_PCIE_CMN_RST BIT(18)
> > #define
> > > +IMX8MM_GPR_PCIE_POWER_OFF BIT(17) #define
> > IMX8MM_GPR_PCIE_SSC_EN
> > > +BIT(16) #define
> > IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE BIT(9)
> > > +
> > > +struct imx8_pcie_phy {
> > > + void __iomem *base;
> > > + struct clk *clk;
> > > + struct phy *phy;
> > > + struct regmap *iomuxc_gpr;
> > > + struct reset_control *reset;
> > > + u32 refclk_pad_mode;
> > > + u32 tx_deemph_gen1;
> > > + u32 tx_deemph_gen2;
> > > + bool clkreq_unused; };
> > > +
> > > +static int imx8_pcie_phy_init(struct phy *phy) {
> > > + int ret;
> > > + u32 val, pad_mode;
> > > + struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
> > > +
> > > + reset_control_assert(imx8_phy->reset);
> > > +
> > > + pad_mode = imx8_phy->refclk_pad_mode;
> > > + /* Set AUX_EN_OVERRIDE 1'b0, when the CLKREQ# isn't
> > hooked */
> > > + regmap_update_bits(imx8_phy->iomuxc_gpr,
> > IOMUXC_GPR14,
> > >
> > + IMX8MM_GPR_PCIE_AUX_EN_
> > OVERRIDE,
> > > + imx8_phy->clkreq_unused ?
> > > + 0 :
> > IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE);
> > > + regmap_update_bits(imx8_phy->iomuxc_gpr,
> > IOMUXC_GPR14,
> > > + IMX8MM_GPR_PCIE_AUX_EN,
> > > + pad_mode ==
> > IMX8_PCIE_REFCLK_PAD_INPUT ?
> > > + IMX8MM_GPR_PCIE_AUX_EN :
> > 0);
> >
> > V3 had IMX8MM_GPR_PCIE_AUX_EN always enabled. Turns out V4
> > stopped working for our output use-case as it only enables it for the input
> > use-case. If I enable this one always it starts working again.
> [Richard Zhu] See my comment above.
> Sorry to bring the regression on your board.
>
Marcel,
Your board does not use an external clk, but does it hook up CLKREQ#
from the socket to either I2C4_SCL or UART4_RXD and pin muxed as such?
For my board that uses an external clk and does not connect CLKREQ# to
the IMX8MM I need to disable that bit. As Richard says we have invalid
documentation for these bits unfortunately which is not helping.
Richard, when we do figure out proper documentation for these bits I
suggest you also add a comment block right above their #defines in the
phy driver with the correct documentation to avoid future confusion.
NXP has had so many mistakes in the various IMX8M RM's and I fear they
will never get fixed.
Best regards,
Tim
More information about the linux-phy
mailing list