[PATCH v3 0/9] add the imx8m pcie phy driver and imx8mm pcie support
Richard Zhu
hongxing.zhu at nxp.com
Tue Oct 26 23:18:38 PDT 2021
> -----Original Message-----
> From: Tim Harvey <tharvey at gateworks.com>
> Sent: Wednesday, October 27, 2021 12:06 AM
> To: Richard Zhu <hongxing.zhu at nxp.com>
> Cc: Lucas Stach <l.stach at pengutronix.de>; Kishon Vijay Abraham I
> <kishon at ti.com>; vkoul at kernel.org; Rob Herring <robh at kernel.org>;
> galak at kernel.crashing.org; Shawn Guo <shawnguo at kernel.org>;
> linux-phy at lists.infradead.org; Device Tree Mailing List
> <devicetree at vger.kernel.org>; Linux ARM Mailing List
> <linux-arm-kernel at lists.infradead.org>; open list
> <linux-kernel at vger.kernel.org>; Sascha Hauer <kernel at pengutronix.de>;
> dl-linux-imx <linux-imx at nxp.com>
> Subject: Re: [PATCH v3 0/9] add the imx8m pcie phy driver and imx8mm pcie
> support
>
> On Mon, Oct 25, 2021 at 10:41 PM Richard Zhu <hongxing.zhu at nxp.com>
> wrote:
> >
> > > -----Original Message-----
> > > From: Tim Harvey <tharvey at gateworks.com>
> > > Sent: Tuesday, October 26, 2021 1:15 AM
> > > To: Richard Zhu <hongxing.zhu at nxp.com>
> > > Cc: Lucas Stach <l.stach at pengutronix.de>; Kishon Vijay Abraham I
> > > <kishon at ti.com>; vkoul at kernel.org; Rob Herring <robh at kernel.org>;
> > > galak at kernel.crashing.org; Shawn Guo <shawnguo at kernel.org>;
> > > linux-phy at lists.infradead.org; Device Tree Mailing List
> > > <devicetree at vger.kernel.org>; Linux ARM Mailing List
> > > <linux-arm-kernel at lists.infradead.org>; open list
> > > <linux-kernel at vger.kernel.org>; Sascha Hauer
> > > <kernel at pengutronix.de>; dl-linux-imx <linux-imx at nxp.com>
> > > Subject: Re: [PATCH v3 0/9] add the imx8m pcie phy driver and imx8mm
> > > pcie support
> > >
> > > On Mon, Oct 25, 2021 at 12:23 AM Richard Zhu <hongxing.zhu at nxp.com>
> > > wrote:
> > > >
> > > > Snipped...
> > > >
> > > > > > > > > > > My boards do not use CLKREQ# so I do not have that
> > > > > > > > > > > defined in pinmux and I found that if I add
> > > > > > > > > > > MX8MM_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B
> > > > > > > > > PCIe
> > > > > > > > > > > works on my board but this isn't a solution just a
> > > > > > > > > > > work-around (I have boards that use the only two
> > > > > > > > > > > possible pins for CLKREQ as other
> > > > > > > > > features).
> > > > > > > > > > >
> > > > > > > > > > > Similarly you will find on the imx8mm-evk if you
> > > > > > > > > > > comment out the CLKREQ (which isn't required) the
> > > > > > > > > > > imx8mmevk will end up hanging like my
> > > > > > > > > boards:
> > > > > > > > > > [Richard Zhu] Hi Tim:
> > > > > > > > > > Regarding the SPEC, the CLKREQ# is mandatory required,
> > > > > > > > > > and should be
> > > > > > > > > configured as an open drain, active low signal.
> > > > > > > > > > And this signal should be driven low by the PCIe M.2
> > > > > > > > > > device to request the
> > > > > > > > > REF clock be available(active low).
> > > > > > > > > > So, there is such kind of CLKREQ# pin definition on
> > > > > > > > > > i.MX8MM EVK
> > > > > > board.
> > > > > > > > > >
> > > > > > > > > > Anyway, I think the external OSC circuit should be
> > > > > > > > > > always running if there is
> > > > > > > > > no CLKREQ# on your HW board design.
> > > > > > > > > >
> > > > > > > > >
> > > > > > > > > The way I understand it is CLKREQ# allows the host to
> > > > > > > > > disable the REFCLK when not needed for power savings so
> > > > > > > > > it would seem optional to implement that and if not
> > > > > > > > > implemented should be left unconnected on
> > > > > > the card.
> > > > > > > > >
> > > > > > > > [Richard Zhu] No, not that way. Regarding the SPEC, this
> > > > > > > > signal is
> > > > > > mandatory required.
> > > > > > > > Especially for the L1ss usages. This signal would be
> > > > > > > > OD(open drain), bi-directional, and might be driven
> > > > > > > > low/high by RC or EP automatically if
> > > > > > L1ss modes are enabled.
> > > > > > > > You can make reference to the
> > > > > > > > "ECN_L1_PM_Substates_with_CLKREQ_31_May_2013_Rev10a",
> or
> > > the
> > > > > > chapter 5.5 L1 PM Substates of "PCI Express Base Specification, Rev.
> > > > > > 4.0 Version 1.0".
> > > > > > > >
> > > > > > >
> > > > > > > CLKREQ is only mandatory if you wish to support clock power
> > > > > > > management. Many boards with a PCI host controller do not
> > > > > > > support this.
> > > > > [Richard Zhu] Okay, understood.
> > > > >
> > > > > > >
> > > > > > > > > > > diff --git
> > > > > > > > > > > a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > > > > > > > > > > b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > > > > > > > > > > index 5ce43daa0c8b..f0023b48f475 100644
> > > > > > > > > > > --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > > > > > > > > > > +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
> > > > > > > > > > > @@ -448,7 +448,9 @@
> > > > > > > > > > >
> > > > > > > > > > > pinctrl_pcie0: pcie0grp {
> > > > > > > > > > > fsl,pins = <
> > > > > > > > > > > +/*
> > > > > > > > > > >
> > > > > > > > > > > MX8MM_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B 0x61
> > > > > > > > > > > +*/
> > > > > > > > > > >
> > > > > > > > > MX8MM_IOMUXC_SAI2_RXFS_GPIO4_IO21
> > > > > > > > > > > 0x41
> > > > > > > > > > > >;
> > > > > > > > > > > };
> > > > > > > > > > >
> > > > > > > > > > > I have PCIe working with a driver that I ported from
> > > > > > > > > > > NXP's kernel which differs from your driver in that
> > > > > > > > > > > the PCIe PHY is not abstracted to its own driver so
> > > > > > > > > > > I think this has something to do with the order in
> > > > > > > > > > > which the phy is reset or
> > > > > initialized?
> > > > > > > > > > > The configuration of
> > > > > > > > > gpr14 bits looks correct to me.
> > > > > > > > > > [Richard Zhu] The CLKREQ# PIN definition shouldn't be
> masked.
> > > > > > > > > > In the NXP's local BSP kernel, I just force CLKREQ#
> > > > > > > > > > low to level up the HW
> > > > > > > > > compatibility.
> > > > > > > > > > That's might the reason why the PCIe works on your HW
> > > > > > > > > > board although the
> > > > > > > > > CLKREQ# PIN is not defined.
> > > > > > > > > > This method is a little rude and violate the SPEC, and
> > > > > > > > > > not recommended
> > > > > > > > > although it levels up the HW compatibility.
> > > > > > > > > > So I drop this method in this series.
> > > > > > > > > >
> > > > > > > > >
> > > > > > > > > Sorry, I don't understand what you are saying here. Is
> > > > > > > > > there a change you are going to make to v4 that will
> > > > > > > > > make this work for the evk and my boards? What is that change
> exactly?
> > > > > > > > [Richard Zhu] No. What I said above is that the CLKREQ# is
> > > > > > > > forced to be low in NXP local BSP kernel. I guess this
> > > > > > > > might be the reason why your
> > > > > > board works.
> > > > > > > >
> > > > > > > > BIT11 and BIT10 of IOMUXC_GPR14 can be used to force the
> > > > > > > > CLKREQ# to
> > > > > > be low.
> > > > > > > > Set CLKREQ_OVERRIDE_EN(bit10) 1b1, then write one zero to
> > > > > > CLKREQ_OVERRIDE(bit11).
> > > > > > > >
> > > > > > >
> > > > > > > Ok, that makes sense. Those bits are not explained well in
> > > > > > > the IMX8MMRM. As my board's external REFCLK is always
> > > > > > > enabled that must gate the clock internally to the host controller
> block.
> > > > > > >
> > > > > > > I can confirm that asserting those GPR14 bits does resolve my
> issue:
> > > > > > >
> > > > > > > #define IMX8MM_GPR_PCIE_CLKREQ_OVERRIDE_VAL BIT(11)
> > > > > > > #define IMX8MM_GPR_PCIE_CLKREQ_OVERRIDE_EN
> BIT(10)
> > > > > > >
> > > > > > > /*
> > > > > > > * for boards that do not connect CLKREQ#,
> > > > > > > * override CLKREQ# and drive it low internally
> > > > > > > */
> > > > > > > regmap_update_bits(imx8_phy->iomuxc_gpr,
> > > IOMUXC_GPR14,
> > > > > > >
> > > > > > IMX8MM_GPR_PCIE_CLKREQ_OVERRIDE_VAL, 0);
> > > > > > > regmap_update_bits(imx8_phy->iomuxc_gpr,
> > > IOMUXC_GPR14,
> > > > > > >
> > > > > > IMX8MM_GPR_PCIE_CLKREQ_OVERRIDE_EN, 1);
> > > > > [Richard Zhu] regmap bits operations should manipulate according
> bits.
> > > > > The BIT(10) and BIT(11) should be touched actually.
> > > > >
> > > > > > >
> > > > > > > Should this be added as a 'fsl,clkreq-unsupported' flag that
> > > > > > > needs to be set true to implement the above code?
> > > > > > >
> > > > > >
> > > > > > Richard,
> > > > > >
> > > > > > Sorry - spoke too soon. My test was flawed as I still was
> > > > > > pinmuxing CLKREQ in my dt to work around the issue and after
> > > > > > removed the above did not resolve my issue. The setting of
> > > > > > OVERRIDE_EN was wrong above (should not be set to '1' but
> > > > > > BIT(10)
> > > > > > instead) but this code already exists in
> > > > > > imx6_pcie_enable_ref_clk and is used for IMX8MM per your patch
> so this is not the issue.
> > > > > >
> > > > > > What makes my board work is to clear GPR14 bit9 (like the NXP
> > > > > > kernel
> > > > > > does) so I don't think this bit does what we think it does
> > > > > > (select between internal and ext clk). I think setting it
> > > > > > enables clock gating via
> > > > > CLKREQ#.
> > > > > >
> > > > > > This also points out that perhaps the CLKREQ_OVERRIDE logic
> > > > > > should be moved to the new phy driver for IMX8MM.
> > > > > [Richard Zhu] It sounds reasonable to consider to force the
> > > > > CLKREQ# to be low.
> > > > > I will think about that and add this in later v5 patch-set if
> > > > > nobody has different concerns.
> > > > > Thanks.
> > > > [Richard Zhu] Hi Tim:
> > > > As you mentioned above, the CLKREQ# GPIO PIN is not used for PCIe
> > > > on
> > > your board, right?
> > > > " (I have boards that use the only two possible pins for CLKREQ as
> > > > other
> > > features)"
> > > >
> > > > Did the override configuration of the clkreq# will bring
> > > > unexpected results
> > > for other features on your board?
> > > >
> > >
> > > What I mean is that imx8mm-venice-gw7901.dts uses both I2C4 and
> > > UART4 and because I2C4_SCL and UART4_RXD are the only two pads that
> > > could be pinmuxed for CLKREQ# I can't use the workaround of pin muxing
> it.
> > >
> > > Currently your driver only works on my imx8mm-venice-* boards if I
> > > add one of the following on boards that don't connect those pads (or
> > > if I clear
> > > IMX8MM_GPR_PCIE_REF_USE_PAD):
> > > MX8MM_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B
> > > MX8MM_IOMUXC_UART4_RXD_PCIE1_CLKREQ_B
> > >
> > > Note your 'PCI: imx: add the imx8mm pcie support' patch [1] does
> > > enable this code already in the imx6_pcie_enable_ref_clk function to
> > > override REF_CLK and drive it low:
> > >
> > > offset = imx6_pcie_grp_offset(imx6_pcie);
> > > /*
> > > * Set the over ride low and enabled
> > > * make sure that REF_CLK is turned on.
> > > */
> > > regmap_update_bits(imx6_pcie->iomuxc_gpr, offset,
> > > IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE,
> > > 0);
> > > regmap_update_bits(imx6_pcie->iomuxc_gpr, offset,
> > > IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN,
> > > IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN);
> > >
> > > So this is already being run and yet my boards still do not work
> > > unless I clr IMX8MM_GPR_PCIE_REF_USE_PAD like this which is what the
> > > NXP downstream driver does:
> > > regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > > IMX8MM_GPR_PCIE_REF_USE_PAD, 0);
> > >
> > > This is why I'm not sure that bit does what you think it does... I
> > > feel like that bit enables 'Use CLKREQ# to enable CLK'.
> > >
> > > You tell me the descriptions for GPR14 are wrong in the reference manual.
> > > Please provide correct descriptions for us so we can sort this out.
> > >
> > [Richard Zhu] Hi Tim:
> > The BIT9 of GPR14 is used as "GPR_PCIE1_PHY_I_AUX_EN_OVERRIDE_EN"
> > and BIT19 is used as "GPR_PCIE1_PHY_FUNC_I_AUX_EN" on i.MX8MM.
> > I think the two bits descriptions are used to describe the BIT19 and BIT9
> together refer to my guess.
> > {GPR_PCIE1_PHY_I_AUX_EN_OVERRIDE_EN(BIT9),
> > GPR_PCIE1_PHY_FUNC_I_AUX_EN(BIT19) }
> > 2'b00: External Reference Clock I/O (for PLL) Disable
> > 2'b01: External Reference Clock I/O (for PLL) Enable
> > 2'b10: External Reference Clock I/O (for PLL) Disable
> > 2'b11: External Reference Clock I/O (for PLL) output is controlled by
> > CLKREQ#
> >
> > The option1&3 should be forbidden, since the external REF CLK I/O should
> be enabled on your board and EVK board.
> > In the option2&4, the BIT19 should be set to be 1'b1.'
> >
> > So, regarding my understand, if the CLKREQ# is not pinmuxed in your use
> case, the IMX8MM_GPR_PCIE_REF_USE_PAD (BIT9) should be 1'b0.
> >
>
> Richard,
>
> Ok, if this is the case then drivers/pci/controller/dwc/pci-imx6.c for IMX8MM
> should not touch GPR14 and '[v3,9/9] PCI: imx: add the imx8mm pcie support'
> should have this on top and squashed:
> diff --git a/drivers/pci/controller/dwc/pci-imx6.c
> b/drivers/pci/controller/dwc/pci-imx6.c
> index 7c89bd1a6441..458d54c8e385 100644
> --- a/drivers/pci/controller/dwc/pci-imx6.c
> +++ b/drivers/pci/controller/dwc/pci-imx6.c
> @@ -452,8 +452,12 @@ static int imx6_pcie_enable_ref_clk(struct
> imx6_pcie *imx6_pcie)
> break;
> case IMX7D:
> break;
> - case IMX8MQ:
> case IMX8MM:
> + ret = clk_prepare_enable(imx6_pcie->pcie_aux);
> + if (ret)
> + dev_err(dev, "unable to enable pcie_aux
> clock\n");
> + break;
> + case IMX8MQ:
> ret = clk_prepare_enable(imx6_pcie->pcie_aux);
> if (ret) {
> dev_err(dev, "unable to enable pcie_aux
> clock\n");
>
[Richard Zhu] Sorry, I might don't understand what's meaning of the changes.
What're the differences between before and after the changes?
>
> And your '[v3,5/9] phy: freescale: pcie: initialize the imx8 pcie standalone phy
> driver' should have this on top and squashed:
> diff --git a/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> index 317cf61bff37..27ca0b9f1d92 100644
> --- a/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> +++ b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> @@ -43,7 +43,7 @@
> #define IMX8MM_GPR_PCIE_CMN_RST BIT(18)
> #define IMX8MM_GPR_PCIE_POWER_OFF BIT(17)
> #define IMX8MM_GPR_PCIE_SSC_EN BIT(16)
> -#define IMX8MM_GPR_PCIE_REF_USE_PAD BIT(9)
> +#define IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE BIT(9)
>
> struct imx8_pcie_phy {
> u32 refclk_pad_mode;
> @@ -63,12 +63,12 @@ static int imx8_pcie_phy_init(struct phy *phy)
> reset_control_assert(imx8_phy->reset);
>
> regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> - IMX8MM_GPR_PCIE_REF_USE_PAD,
> - imx8_phy->refclk_pad_mode == 1 ?
> - IMX8MM_GPR_PCIE_REF_USE_PAD : 0);
> + IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE,
> + 0);
> regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> IMX8MM_GPR_PCIE_AUX_EN,
> - IMX8MM_GPR_PCIE_AUX_EN);
> + imx8_phy->refclk_pad_mode ==
> IMX8_PCIE_REFCLK_PAD_INPUT ?
> + IMX8MM_GPR_PCIE_AUX_EN : 0);
> regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> IMX8MM_GPR_PCIE_POWER_OFF, 0);
> regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14, @@
> -76,7 +76,7 @@ static int imx8_pcie_phy_init(struct phy *phy)
>
> regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> IMX8MM_GPR_PCIE_REF_CLK_SEL,
> - imx8_phy->refclk_pad_mode == 1 ?
> + imx8_phy->refclk_pad_mode ==
> IMX8_PCIE_REFCLK_PAD_INPUT ?
> IMX8MM_GPR_PCIE_REF_CLK_EXT :
> IMX8MM_GPR_PCIE_REF_CLK_PLL);
> usleep_range(100, 200);
>
> I tested this and it works both on imx8mm-evk and imx8mm-venice-* which
> both have external clkgen.
>
> However, the above does not set IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE
> for the case where CLKREQ# is connected and thus should be used so I think
> we need to add a property for that to define if CLKREQ# is hooked up or not. I
> tested enabling IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE and as expected
> that worked on the imx8mm-evk which hooks up CLKREQ# but not
> imx8mm-venice which does not hook up CLKREQ#.
>
> What do you think about adding a property for this?
[Richard Zhu] First of all, thanks a lot for your help to figure out the details.
Agree with your proposal.
One optional property "fsl,clkreq-unsupported" would be added for the CLKREQ# not hooked case later.
diff --git a/Documentation/devicetree/bindings/phy/fsl,imx8-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/fsl,imx8-pcie-phy.yaml
index 097ba2a28fb4..2264452924cc 100644
--- a/Documentation/devicetree/bindings/phy/fsl,imx8-pcie-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/fsl,imx8-pcie-phy.yaml
@@ -58,6 +58,11 @@ properties:
$ref: /schemas/types.yaml#/definitions/uint32
default: 0
+ fsl,clkreq-unsupported:
+ type: boolean
+ description: A boolean property whoes presence indicates the CLKREQ#
+ signal isn't supported in the HW board design (optional required).
+
diff --git a/drivers/phy/freescale/phy-fsl-imx8m-pcie.c b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
index 07eea39283ed..4b4402eaddcc 100644
--- a/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
+++ b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
@@ -43,7 +43,7 @@
#define IMX8MM_GPR_PCIE_CMN_RST BIT(18)
#define IMX8MM_GPR_PCIE_POWER_OFF BIT(17)
#define IMX8MM_GPR_PCIE_SSC_EN BIT(16)
-#define IMX8MM_GPR_PCIE_REF_USE_PAD BIT(9)
+#define IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE BIT(9)
struct imx8_pcie_phy {
void __iomem *base;
@@ -54,6 +54,7 @@ struct imx8_pcie_phy {
u32 refclk_pad_mode;
u32 tx_deemph_gen1;
u32 tx_deemph_gen2;
+ bool clkreq_unused;
};
static int imx8_pcie_phy_init(struct phy *phy)
@@ -65,13 +66,15 @@ static int imx8_pcie_phy_init(struct phy *phy)
reset_control_assert(imx8_phy->reset);
pad_mode = imx8_phy->refclk_pad_mode;
+ /* Set AUX_EN_OVERRIDE 1'b0, when the CLKREQ# isn't hooked */
regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
- IMX8MM_GPR_PCIE_REF_USE_PAD,
- pad_mode == IMX8MM_GPR_PCIE_REF_USE_PAD ?
- IMX8MM_GPR_PCIE_REF_USE_PAD : 0);
+ IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE,
+ imx8_phy->clkreq_unused ?
+ 0 : IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE);
regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
IMX8MM_GPR_PCIE_AUX_EN,
- IMX8MM_GPR_PCIE_AUX_EN);
+ pad_mode == IMX8_PCIE_REFCLK_PAD_INPUT ?
+ IMX8MM_GPR_PCIE_AUX_EN : 0);
regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
IMX8MM_GPR_PCIE_POWER_OFF, 0);
regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
@@ -171,6 +174,11 @@ static int imx8_pcie_phy_probe(struct platform_device *pdev)
&imx8_phy->tx_deemph_gen2))
imx8_phy->tx_deemph_gen2 = 0;
+ if (of_property_read_bool(np, "fsl,clkreq-unsupported"))
+ imx8_phy->clkreq_unused = true;
+ else
+ imx8_phy->clkreq_unused = false;
+
imx8_phy->clk = devm_clk_get(dev, "ref");
if (IS_ERR(imx8_phy->clk)) {
dev_err(dev, "failed to get imx pcie phy clock\n");
Best Regards
Richard Zhu
>
> Best regards,
>
> Tim
More information about the linux-phy
mailing list