[PATCH v7 0/4] Rx mode support for Cadence DPHY

[Pratyush Yadav]

Hi,

This series adds support for Cadence DPHY Rx driver. It has been split
off from [0] to facilitate easier merging. I have still kept the version
number to maintain continuity with the previous patches. The earlier
version used the same binding for Tx and Rx DPHY. With the separate
driver, I have added a separate binding. But I am still keeping the old
conversion patch in this series since I have already done the work in
converting the binding to yaml, might as well get it merged.

Tested on TI's J721E with OV5640 sensor.

[0] https://patchwork.linuxtv.org/project/linux-media/list/?series=5526&state=%2A&archive=both

Changes in v7:
- Add spaces after { and before } in the bands table.
- Drop the wrapping around the for loop on cdns_dphy_rx_get_band_ctrl().
- Make cdns_dphy_rx_wait_for_bit() inline.
- Print an error message if registering PHY provider fails.

Changes in v6:
- Add a new binding for DPHY Rx.
- Move the DPHY Rx part to a separate driver.
- Drop Rx specific changes from the cdns,dphy.yaml binding. Keep those
  in cdns,dphy-rx.yaml

Changes in v5:
- Use the new cdns_dphy_info to specify PHY ops.
- Re-order include in alphabetical order.
- Make bands const.
- Drop num_bands.
- Make i, lanes unsigned.
- Drop the maximum check in cdns_dphy_rx_get_band_ctrl(). Let the loop
  complete and return -EOPNOTSUPP when we reach the end.
- Drop the "rate < bands[i].min_rate" check since the bands are in
  ascending order.
- Move data_lane_ctrl to start of function and make it static const.

Changes in v4:
- Drop the submode parts. Use a different compatible for the Rx ops.
- Make bands and num_bands static.
- Drop the submode patches. Use a different compatible for Rx mode DPHY
instead.

Changes in v3:
- Use a table to select the band.
- Use a table to poll the data lane ready bits.
- Multiply the DPHY HS clock rate by 2 to get the bit rate since the
  clock is DDR.
- Add Rob's R-by.

Changes in v2:
- Drop reg description.
- Add a description for each DPHY clock.
- Rename dphy at ... to phy at ... in example.
- Add Laurent's R-by.
- Re-order subject prefixes.
- Add power-domain to the example.
- Add Laurent's R-by.
- Re-order subject prefixes.

Pratyush Yadav (4):
  phy: cadence: Add Cadence D-PHY Rx driver
  phy: dt-bindings: Convert Cadence DPHY binding to YAML
  phy: dt-bindings: cdns,dphy: add power-domains property
  phy: dt-bindings: Add Cadence D-PHY Rx bindings

 .../devicetree/bindings/phy/cdns,dphy-rx.yaml |  42 +++
 .../devicetree/bindings/phy/cdns,dphy.txt     |  20 --
 .../devicetree/bindings/phy/cdns,dphy.yaml    |  56 ++++
 drivers/phy/cadence/Kconfig                   |   8 +
 drivers/phy/cadence/Makefile                  |   1 +
 drivers/phy/cadence/cdns-dphy-rx.c            | 255 ++++++++++++++++++
 6 files changed, 362 insertions(+), 20 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/phy/cdns,dphy-rx.yaml
 delete mode 100644 Documentation/devicetree/bindings/phy/cdns,dphy.txt
 create mode 100644 Documentation/devicetree/bindings/phy/cdns,dphy.yaml
 create mode 100644 drivers/phy/cadence/cdns-dphy-rx.c

-- 
2.33.1.835.ge9e5ba39a7