[RFC PATCH v4 3/4] phy: rockchip: add naneng combo phy for RK3568
Vinod Koul
vkoul at kernel.org
Tue Dec 14 01:11:13 PST 2021
On 08-12-21, 19:54, Johan Jonker wrote:
> From: Yifeng Zhao <yifeng.zhao at rock-chips.com>
>
> This patch implements a combo phy driver for Rockchip SoCs
> with NaNeng IP block. This phy can be used as pcie-phy, usb3-phy,
> sata-phy or sgmii-phy.
>
> Signed-off-by: Yifeng Zhao <yifeng.zhao at rock-chips.com>
> Signed-off-by: Johan Jonker <jbx6244 at gmail.com>
> ---
>
> TEST COMPILED ONLY!
> Driver not verified with hardware!
> ---
>
> Changed V4:
> restyle
> add devm_reset_control_array_get()
> remove clk structure
> change refclk DT parse
> change dev_err message
> add dot to phrase
> add ext_refclk variable
> add enable_ssc variable
> rename rockchip_combphy_param_write
> remove param_read
> replace rockchip-naneng-combphy driver name
> ---
> drivers/phy/rockchip/Kconfig | 8 +
> drivers/phy/rockchip/Makefile | 1 +
> .../rockchip/phy-rockchip-naneng-combphy.c | 608 ++++++++++++++++++
> 3 files changed, 617 insertions(+)
> create mode 100644 drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
>
> diff --git a/drivers/phy/rockchip/Kconfig b/drivers/phy/rockchip/Kconfig
> index e812adad7..9022e395c 100644
> --- a/drivers/phy/rockchip/Kconfig
> +++ b/drivers/phy/rockchip/Kconfig
> @@ -66,6 +66,14 @@ config PHY_ROCKCHIP_INNO_DSIDPHY
> Enable this to support the Rockchip MIPI/LVDS/TTL PHY with
> Innosilicon IP block.
>
> +config PHY_ROCKCHIP_NANENG_COMBO_PHY
> + tristate "Rockchip NANENG COMBO PHY Driver"
> + depends on ARCH_ROCKCHIP && OF
> + select GENERIC_PHY
> + help
> + Enable this to support the Rockchip PCIe/USB3.0/SATA/QSGMII
> + combo PHY with NaNeng IP block.
> +
> config PHY_ROCKCHIP_PCIE
> tristate "Rockchip PCIe PHY Driver"
> depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST
> diff --git a/drivers/phy/rockchip/Makefile b/drivers/phy/rockchip/Makefile
> index f0eec212b..a5041efb5 100644
> --- a/drivers/phy/rockchip/Makefile
> +++ b/drivers/phy/rockchip/Makefile
> @@ -6,6 +6,7 @@ obj-$(CONFIG_PHY_ROCKCHIP_INNO_CSIDPHY) += phy-rockchip-inno-csidphy.o
> obj-$(CONFIG_PHY_ROCKCHIP_INNO_DSIDPHY) += phy-rockchip-inno-dsidphy.o
> obj-$(CONFIG_PHY_ROCKCHIP_INNO_HDMI) += phy-rockchip-inno-hdmi.o
> obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2) += phy-rockchip-inno-usb2.o
> +obj-$(CONFIG_PHY_ROCKCHIP_NANENG_COMBO_PHY) += phy-rockchip-naneng-combphy.o
> obj-$(CONFIG_PHY_ROCKCHIP_PCIE) += phy-rockchip-pcie.o
> obj-$(CONFIG_PHY_ROCKCHIP_TYPEC) += phy-rockchip-typec.o
> obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
> diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> new file mode 100644
> index 000000000..56aaeed62
> --- /dev/null
> +++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> @@ -0,0 +1,608 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Rockchip PIPE USB3.0 PCIE SATA combphy driver
> + *
> + * Copyright (C) 2021 Rockchip Electronics Co., Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/phy/phy.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <dt-bindings/phy/phy.h>
> +
> +#define BIT_WRITEABLE_SHIFT 16
> +#define REF_CLOCK_24MHz 24000000
How about 24 * MEGA (see units.h)
> +#define REF_CLOCK_25MHz 25000000
> +#define REF_CLOCK_100MHz 100000000
empty line here pls
> +/* RK3568 T22 COMBO PHY REG */
> +#define RK3568_T22_PHYREG5 0x14
> +#define T22_PHYREG5_PLL_DIV_MASK GENMASK(7, 6)
> +#define T22_PHYREG5_PLL_DIV_SHIFT 6
> +#define T22_PHYREG5_PLL_DIV_2 1
> +
> +#define RK3568_T22_PHYREG6 0x18
> +#define T22_PHYREG6_TX_RTERM_MASK GENMASK(7, 4)
> +#define T22_PHYREG6_TX_RTERM_SHIFT 4
> +#define T22_PHYREG6_TX_RTERM_50OHM 0x8
> +#define T22_PHYREG6_RX_RTERM_MASK GENMASK(3, 0)
> +#define T22_PHYREG6_RX_RTERM_SHIFT 0
You can avoid using SHIFT macros by defining register masks using BIT,
GENMASK and then use FIELD_PREP() and FIELD_GET() to set and get
register values
> +#define T22_PHYREG6_RX_RTERM_44OHM 0xF
> +
> +#define RK3568_T22_PHYREG7 0x1C
> +#define T22_PHYREG7_SSC_EN BIT(4)
> +
> +#define RK3568_T22_PHYREG10 0x28
> +#define T22_PHYREG10_SU_TRIM_0_7 0xF0
GENMASK() ?
> +
> +#define RK3568_T22_PHYREG11 0x2C
> +#define T22_PHYREG11_PLL_LPF_ADJ 0x4
BIT(), here and other places applicable
> +
> +#define RK3568_T22_PHYREG12 0x30
> +#define T22_PHYREG12_RESISTER_MASK GENMASK(5, 4)
> +#define T22_PHYREG12_RESISTER_SHIFT 0x4
> +#define T22_PHYREG12_RESISTER_HIGH_Z 0x3
> +#define T22_PHYREG12_CKRCV_AMP0 BIT(7)
> +
> +#define RK3568_T22_PHYREG13 0x34
> +#define T22_PHYREG13_CKRCV_AMP1 BIT(0)
> +
> +#define RK3568_T22_PHYREG14 0x38
> +#define T22_PHYREG14_CTLE_EN BIT(0)
> +#define T22_PHYREG14_SSC_CNT_MASK GENMASK(7, 6)
> +#define T22_PHYREG14_SSC_CNT_SHIFT 6
> +#define T22_PHYREG14_SSC_CNT_VALUE 0x1
> +
> +#define RK3568_T22_PHYREG15 0x3C
> +#define T22_PHYREG15_SSC_CNT_VALUE 0x5f
> +
> +#define RK3568_T22_PHYREG17 0x44
> +#define T22_PHYREG17_PLL_LOOP 0x32
> +
> +#define RK3568_T22_PHYREG31 0x7C
> +#define T22_PHYREG31_SSC_MASK GENMASK(7, 4)
> +#define T22_PHYREG31_SSC_DIR_SHIFT 4
> +#define T22_PHYREG31_SSC_UPWARD 0
> +#define T22_PHYREG31_SSC_DOWNWARD 1
> +#define T22_PHYREG31_SSC_OFFSET_SHIFT 6
> +#define T22_PHYREG31_SSC_OFFSET_500PPM 1
> +
> +#define RK3568_T22_PHYREG32 0x80
> +#define T22_PHYREG32_PLL_KVCO_MASK GENMASK(4, 2)
> +#define T22_PHYREG32_PLL_KVCO_SHIFT 2
> +#define T22_PHYREG32_PLL_KVCO_VALUE 2
> +
> +struct rockchip_combphy_priv;
> +
> +struct combphy_reg {
> + u16 offset;
> + u16 bitend;
> + u16 bitstart;
> + u16 disable;
> + u16 enable;
> +};
> +
> +struct rockchip_combphy_grfcfg {
> + struct combphy_reg pcie_mode_set;
> + struct combphy_reg usb_mode_set;
> + struct combphy_reg sgmii_mode_set;
> + struct combphy_reg qsgmii_mode_set;
> + struct combphy_reg pipe_rxterm_set;
> + struct combphy_reg pipe_txelec_set;
> + struct combphy_reg pipe_txcomp_set;
> + struct combphy_reg pipe_clk_25m;
> + struct combphy_reg pipe_clk_100m;
> + struct combphy_reg pipe_phymode_sel;
> + struct combphy_reg pipe_rate_sel;
> + struct combphy_reg pipe_rxterm_sel;
> + struct combphy_reg pipe_txelec_sel;
> + struct combphy_reg pipe_txcomp_sel;
> + struct combphy_reg pipe_clk_ext;
> + struct combphy_reg pipe_sel_usb;
> + struct combphy_reg pipe_sel_qsgmii;
> + struct combphy_reg pipe_phy_status;
> + struct combphy_reg con0_for_pcie;
> + struct combphy_reg con1_for_pcie;
> + struct combphy_reg con2_for_pcie;
> + struct combphy_reg con3_for_pcie;
> + struct combphy_reg con0_for_sata;
> + struct combphy_reg con1_for_sata;
> + struct combphy_reg con2_for_sata;
> + struct combphy_reg con3_for_sata;
> + struct combphy_reg pipe_con0_for_sata;
> + struct combphy_reg pipe_sgmii_mac_sel;
> + struct combphy_reg pipe_xpcs_phy_ready;
> + struct combphy_reg u3otg0_port_en;
> + struct combphy_reg u3otg1_port_en;
> +};
> +
> +struct rockchip_combphy_cfg {
> + const struct rockchip_combphy_grfcfg *grfcfg;
> + int (*combphy_cfg)(struct rockchip_combphy_priv *priv);
> +};
> +
> +struct rockchip_combphy_priv {
> + u8 mode;
> + void __iomem *mmio;
> + int num_clks;
> + struct clk_bulk_data *clks;
> + struct device *dev;
> + struct regmap *pipe_grf;
> + struct regmap *phy_grf;
> + struct phy *phy;
> + struct reset_control *phy_rst;
> + const struct rockchip_combphy_cfg *cfg;
> + bool enable_ssc;
> + bool ext_refclk;
> + struct clk *refclk;
> +};
> +
> +static int rockchip_combphy_param_write(struct regmap *base,
> + const struct combphy_reg *reg, bool en)
pls align to previous line open brace (hint, checkpatch with --strict
will find these for you)
> +{
> + u32 val, mask, tmp;
> +
> + tmp = en ? reg->enable : reg->disable;
> + mask = GENMASK(reg->bitend, reg->bitstart);
> + val = (tmp << reg->bitstart) | (mask << BIT_WRITEABLE_SHIFT);
> +
> + return regmap_write(base, reg->offset, val);
> +}
> +
> +static u32 rockchip_combphy_is_ready(struct rockchip_combphy_priv *priv)
> +{
> + const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> + u32 mask, val;
> +
> + mask = GENMASK(cfg->pipe_phy_status.bitend,
> + cfg->pipe_phy_status.bitstart);
> +
> + regmap_read(priv->phy_grf, cfg->pipe_phy_status.offset, &val);
> + val = (val & mask) >> cfg->pipe_phy_status.bitstart;
> +
> + return val;
> +}
> +
> +static int rockchip_combphy_set_mode(struct rockchip_combphy_priv *priv)
> +{
> + int ret = 0;
> +
> + switch (priv->mode) {
> + case PHY_TYPE_PCIE:
> + case PHY_TYPE_USB3:
> + case PHY_TYPE_SATA:
> + case PHY_TYPE_SGMII:
> + case PHY_TYPE_QSGMII:
> + if (priv->cfg->combphy_cfg)
> + ret = priv->cfg->combphy_cfg(priv);
> + break;
> + default:
> + dev_err(priv->dev, "incompatible PHY type\n");
> + return -EINVAL;
> + }
> +
> + if (ret)
> + dev_err(priv->dev, "failed to init phy for phy mode %x\n", priv->mode);
> +
> + return ret;
> +}
> +
> +static int rockchip_combphy_init(struct phy *phy)
> +{
> + struct rockchip_combphy_priv *priv = phy_get_drvdata(phy);
> + const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> + u32 val;
> + int ret;
> +
> + ret = clk_bulk_prepare_enable(priv->num_clks, priv->clks);
> + if (ret) {
> + dev_err(priv->dev, "failed to enable clks\n");
> + return ret;
> + }
> +
> + ret = rockchip_combphy_set_mode(priv);
> + if (ret)
> + goto err_clk;
> +
> + ret = reset_control_deassert(priv->phy_rst);
> + if (ret)
> + goto err_clk;
> +
> + if (priv->mode == PHY_TYPE_USB3) {
> + ret = readx_poll_timeout_atomic(rockchip_combphy_is_ready,
> + priv, val,
> + val == cfg->pipe_phy_status.enable,
> + 10, 1000);
> + if (ret)
> + dev_warn(priv->dev, "wait phy status ready timeout\n");
> + }
> +
> + return 0;
> +
> +err_clk:
> + clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
> +
> + return ret;
> +}
> +
> +static int rockchip_combphy_exit(struct phy *phy)
> +{
> + struct rockchip_combphy_priv *priv = phy_get_drvdata(phy);
> +
> + clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
> + reset_control_assert(priv->phy_rst);
> +
> + return 0;
> +}
> +
> +static const struct phy_ops rochchip_combphy_ops = {
> + .init = rockchip_combphy_init,
> + .exit = rockchip_combphy_exit,
> + .owner = THIS_MODULE,
> +};
> +
> +static struct phy *rockchip_combphy_xlate(struct device *dev, struct of_phandle_args *args)
> +{
> + struct rockchip_combphy_priv *priv = dev_get_drvdata(dev);
> +
> + if (args->args_count != 1) {
> + dev_err(dev, "invalid number of arguments\n");
> + return ERR_PTR(-EINVAL);
> + }
> +
> + if (priv->mode != PHY_NONE && priv->mode != args->args[0])
> + dev_warn(dev, "phy type select %d overwriting type %d\n",
> + args->args[0], priv->mode);
> +
> + priv->mode = args->args[0];
> +
> + return priv->phy;
> +}
> +
> +static int rockchip_combphy_parse_dt(struct device *dev, struct rockchip_combphy_priv *priv)
> +{
> + const struct rockchip_combphy_cfg *phy_cfg = priv->cfg;
> + int mac_id;
> + int i;
> +
> + priv->num_clks = devm_clk_bulk_get_all(dev, &priv->clks);
> + if (priv->num_clks < 1)
> + return -EINVAL;
> +
> + priv->refclk = NULL;
> + for (i = 0; i < priv->num_clks; i++) {
> + if (!strncmp(priv->clks[i].id, "ref", 3)) {
> + priv->refclk = priv->clks[i].clk;
> + break;
> + }
> + }
> +
> + if (!priv->refclk) {
> + dev_err(dev, "no refclk found\n");
> + return -EINVAL;
> + }
> +
> + priv->pipe_grf = syscon_regmap_lookup_by_phandle(dev->of_node, "rockchip,pipe-grf");
> + if (IS_ERR(priv->pipe_grf)) {
> + dev_err(dev, "failed to find peri_ctrl pipe-grf regmap\n");
> + return PTR_ERR(priv->pipe_grf);
> + }
> +
> + priv->phy_grf = syscon_regmap_lookup_by_phandle(dev->of_node, "rockchip,pipe-phy-grf");
> + if (IS_ERR(priv->phy_grf)) {
> + dev_err(dev, "failed to find peri_ctrl pipe-phy-grf regmap\n");
> + return PTR_ERR(priv->phy_grf);
> + }
> +
> + if (device_property_present(dev, "rockchip,dis-u3otg0-port"))
> + rockchip_combphy_param_write(priv->pipe_grf, &phy_cfg->grfcfg->u3otg0_port_en,
> + false);
> +
> + if (device_property_present(dev, "rockchip,dis-u3otg1-port"))
> + rockchip_combphy_param_write(priv->pipe_grf, &phy_cfg->grfcfg->u3otg1_port_en,
> + false);
> +
> + priv->enable_ssc = device_property_present(dev, "rockchip,enable-ssc");
> +
> + priv->ext_refclk = device_property_present(dev, "rockchip,ext-refclk");
> +
> + if (!device_property_read_u32(dev, "rockchip,sgmii-mac-sel", &mac_id) &&
> + (mac_id > 0))
> + rockchip_combphy_param_write(priv->pipe_grf, &phy_cfg->grfcfg->pipe_sgmii_mac_sel,
> + true);
> + else
> + rockchip_combphy_param_write(priv->pipe_grf, &phy_cfg->grfcfg->pipe_sgmii_mac_sel,
> + false);
> +
> + priv->phy_rst = devm_reset_control_array_get(dev, false, false);
> + if (IS_ERR(priv->phy_rst))
> + return dev_err_probe(dev, PTR_ERR(priv->phy_rst), "failed to get phy reset\n");
> +
> + return 0;
> +}
> +
> +static int rockchip_combphy_probe(struct platform_device *pdev)
> +{
> + struct phy_provider *phy_provider;
> + struct device *dev = &pdev->dev;
> + struct rockchip_combphy_priv *priv;
> + const struct rockchip_combphy_cfg *phy_cfg;
> + struct resource *res;
> + int ret;
> +
> + phy_cfg = of_device_get_match_data(dev);
> + if (!phy_cfg) {
> + dev_err(dev, "no OF match data provided\n");
> + return -EINVAL;
> + }
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + priv->mmio = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
> + if (IS_ERR(priv->mmio)) {
> + ret = PTR_ERR(priv->mmio);
> + return ret;
> + }
> +
> + priv->dev = dev;
> + priv->mode = PHY_NONE;
> + priv->cfg = phy_cfg;
> +
> + ret = rockchip_combphy_parse_dt(dev, priv);
> + if (ret)
> + return ret;
> +
> + ret = reset_control_assert(priv->phy_rst);
> + if (ret) {
> + dev_err(dev, "failed to reset phy\n");
> + return ret;
> + }
> +
> + priv->phy = devm_phy_create(dev, NULL, &rochchip_combphy_ops);
> + if (IS_ERR(priv->phy)) {
> + dev_err(dev, "failed to create combphy\n");
> + return PTR_ERR(priv->phy);
> + }
> +
> + dev_set_drvdata(dev, priv);
> + phy_set_drvdata(priv->phy, priv);
> +
> + phy_provider = devm_of_phy_provider_register(dev, rockchip_combphy_xlate);
> +
> + return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
> +{
> + const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> + unsigned long rate;
> + u32 val;
> +
> + switch (priv->mode) {
> + case PHY_TYPE_PCIE:
> + /* Set SSC downward spread spectrum. */
> + val = readl(priv->mmio + RK3568_T22_PHYREG31);
> + val &= ~T22_PHYREG31_SSC_MASK;
> + val |= T22_PHYREG31_SSC_DOWNWARD << T22_PHYREG31_SSC_DIR_SHIFT;
> + writel(val, priv->mmio + RK3568_T22_PHYREG31);
> +
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
> + break;
empty line here helps readability
> + case PHY_TYPE_USB3:
> + /* Set SSC downward spread spectrum. */
> + val = readl(priv->mmio + RK3568_T22_PHYREG31);
> + val &= ~T22_PHYREG31_SSC_MASK;
> + val |= T22_PHYREG31_SSC_DOWNWARD << T22_PHYREG31_SSC_DIR_SHIFT;
> + writel(val, priv->mmio + RK3568_T22_PHYREG31);
perhaps a updatel() macro to help with this?
> +
> + /* Enable adaptive CTLE for USB3.0 Rx. */
> + val = readl(priv->mmio + RK3568_T22_PHYREG14);
> + val |= T22_PHYREG14_CTLE_EN;
> + writel(val, priv->mmio + RK3568_T22_PHYREG14);
> +
> + /* Set PLL KVCO fine tuning signals. */
> + val = readl(priv->mmio + RK3568_T22_PHYREG32);
> + val &= ~T22_PHYREG32_PLL_KVCO_MASK;
> + val |= T22_PHYREG32_PLL_KVCO_VALUE << T22_PHYREG32_PLL_KVCO_SHIFT;
> + writel(val, priv->mmio + RK3568_T22_PHYREG32);
> +
> + /* Enable controlling random jitter. */
> + writel(T22_PHYREG11_PLL_LPF_ADJ, priv->mmio + RK3568_T22_PHYREG11);
> +
> + /* Set PLL input clock divider 1/2. */
> + val = readl(priv->mmio + RK3568_T22_PHYREG5);
> + val &= ~T22_PHYREG5_PLL_DIV_MASK;
> + val |= T22_PHYREG5_PLL_DIV_2 << T22_PHYREG5_PLL_DIV_SHIFT;
> + writel(val, priv->mmio + RK3568_T22_PHYREG5);
> +
> + writel(T22_PHYREG17_PLL_LOOP, priv->mmio + RK3568_T22_PHYREG17);
> + writel(T22_PHYREG10_SU_TRIM_0_7, priv->mmio + RK3568_T22_PHYREG10);
> +
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_sel_usb, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->usb_mode_set, true);
> + break;
> + case PHY_TYPE_SATA:
> + /* Enable adaptive CTLE for SATA Rx. */
> + val = readl(priv->mmio + RK3568_T22_PHYREG14);
> + val |= T22_PHYREG14_CTLE_EN;
> + writel(val, priv->mmio + RK3568_T22_PHYREG14);
> + /*
> + * Set tx_rterm=50ohm and rx_rterm=44ohm for SATA.
> + * 0: 60ohm, 8: 50ohm 15: 44ohm (by step abort 1ohm)
> + */
> + val = T22_PHYREG6_TX_RTERM_50OHM << T22_PHYREG6_TX_RTERM_SHIFT;
> + val |= T22_PHYREG6_RX_RTERM_44OHM << T22_PHYREG6_RX_RTERM_SHIFT;
> + writel(val, priv->mmio + RK3568_T22_PHYREG6);
> +
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_sata, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_sata, true);
> + rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con0_for_sata, true);
> + break;
> + case PHY_TYPE_SGMII:
> + rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_xpcs_phy_ready, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_phymode_sel, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_sel_qsgmii, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->sgmii_mode_set, true);
> + break;
> + case PHY_TYPE_QSGMII:
> + rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_xpcs_phy_ready, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_phymode_sel, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_rate_sel, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_sel_qsgmii, true);
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->qsgmii_mode_set, true);
> + break;
> + default:
> + dev_err(priv->dev, "incompatible PHY type\n");
> + return -EINVAL;
> + }
> +
> + rate = clk_get_rate(priv->refclk);
> +
> + switch (rate) {
> + case REF_CLOCK_24MHz:
> + if (priv->mode == PHY_TYPE_USB3 || priv->mode == PHY_TYPE_SATA) {
> + /* Set ssc_cnt[9:0]=0101111101 & 31.5KHz. */
> + val = readl(priv->mmio + RK3568_T22_PHYREG14);
> + val &= ~T22_PHYREG14_SSC_CNT_MASK;
> + val |= T22_PHYREG14_SSC_CNT_VALUE << T22_PHYREG14_SSC_CNT_SHIFT;
> + writel(val, priv->mmio + RK3568_T22_PHYREG14);
> + writel(T22_PHYREG15_SSC_CNT_VALUE, priv->mmio + RK3568_T22_PHYREG15);
> + }
> + break;
> + case REF_CLOCK_25MHz:
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_25m, true);
> + break;
> + case REF_CLOCK_100MHz:
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
> + if (priv->mode == PHY_TYPE_PCIE) {
> + /* PLL KVCO fine tuning. */
> + val = readl(priv->mmio + RK3568_T22_PHYREG32);
> + val &= ~T22_PHYREG32_PLL_KVCO_MASK;
> + val |= T22_PHYREG32_PLL_KVCO_VALUE << T22_PHYREG32_PLL_KVCO_SHIFT;
> + writel(val, priv->mmio + RK3568_T22_PHYREG32);
> +
> + /* Enable controlling random jitter. */
> + writel(T22_PHYREG11_PLL_LPF_ADJ, priv->mmio + RK3568_T22_PHYREG11);
> +
> + val = readl(priv->mmio + RK3568_T22_PHYREG5);
> + val &= ~T22_PHYREG5_PLL_DIV_MASK;
> + val |= T22_PHYREG5_PLL_DIV_2 << T22_PHYREG5_PLL_DIV_SHIFT;
> + writel(val, priv->mmio + RK3568_T22_PHYREG5);
> +
> + writel(T22_PHYREG17_PLL_LOOP, priv->mmio + RK3568_T22_PHYREG17);
> + writel(T22_PHYREG10_SU_TRIM_0_7, priv->mmio + RK3568_T22_PHYREG10);
> + } else if (priv->mode == PHY_TYPE_SATA) {
> + /* downward spread spectrum +500ppm */
> + val = readl(priv->mmio + RK3568_T22_PHYREG31);
> + val &= ~T22_PHYREG31_SSC_MASK;
> + val |= T22_PHYREG31_SSC_DOWNWARD << T22_PHYREG31_SSC_DIR_SHIFT;
> + val |= T22_PHYREG31_SSC_OFFSET_500PPM << T22_PHYREG31_SSC_OFFSET_SHIFT;
> + writel(val, priv->mmio + RK3568_T22_PHYREG31);
> + }
> + break;
> + default:
> + dev_err(priv->dev, "unsupported rate: %lu\n", rate);
> + return -EINVAL;
> + }
> +
> + if (priv->ext_refclk) {
> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
> + if (priv->mode == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
> + val = readl(priv->mmio + RK3568_T22_PHYREG12);
> + val &= ~T22_PHYREG12_RESISTER_MASK;
> + val |= T22_PHYREG12_RESISTER_HIGH_Z << T22_PHYREG12_RESISTER_SHIFT;
> + val |= T22_PHYREG12_CKRCV_AMP0;
> + writel(val, priv->mmio + RK3568_T22_PHYREG12);
> +
> + val = readl(priv->mmio + RK3568_T22_PHYREG13);
> + val |= T22_PHYREG13_CKRCV_AMP1;
> + writel(val, priv->mmio + RK3568_T22_PHYREG13);
> + }
> + }
> +
> + if (priv->enable_ssc) {
> + val = readl(priv->mmio + RK3568_T22_PHYREG7);
> + val |= T22_PHYREG7_SSC_EN;
> + writel(val, priv->mmio + RK3568_T22_PHYREG7);
> + }
> +
> + return 0;
> +}
> +
> +static const struct rockchip_combphy_grfcfg rk3568_combphy_grfcfgs = {
> + /* pipe-phy-grf */
> + .pcie_mode_set = { 0x0000, 5, 0, 0x00, 0x11 },
> + .usb_mode_set = { 0x0000, 5, 0, 0x00, 0x04 },
> + .sgmii_mode_set = { 0x0000, 5, 0, 0x00, 0x01 },
> + .qsgmii_mode_set = { 0x0000, 5, 0, 0x00, 0x21 },
> + .pipe_rxterm_set = { 0x0000, 12, 12, 0x00, 0x01 },
> + .pipe_txelec_set = { 0x0004, 1, 1, 0x00, 0x01 },
> + .pipe_txcomp_set = { 0x0004, 4, 4, 0x00, 0x01 },
> + .pipe_clk_25m = { 0x0004, 14, 13, 0x00, 0x01 },
> + .pipe_clk_100m = { 0x0004, 14, 13, 0x00, 0x02 },
> + .pipe_phymode_sel = { 0x0008, 1, 1, 0x00, 0x01 },
> + .pipe_rate_sel = { 0x0008, 2, 2, 0x00, 0x01 },
> + .pipe_rxterm_sel = { 0x0008, 8, 8, 0x00, 0x01 },
> + .pipe_txelec_sel = { 0x0008, 12, 12, 0x00, 0x01 },
> + .pipe_txcomp_sel = { 0x0008, 15, 15, 0x00, 0x01 },
> + .pipe_clk_ext = { 0x000c, 9, 8, 0x02, 0x01 },
> + .pipe_sel_usb = { 0x000c, 14, 13, 0x00, 0x01 },
> + .pipe_sel_qsgmii = { 0x000c, 15, 13, 0x00, 0x07 },
> + .pipe_phy_status = { 0x0034, 6, 6, 0x01, 0x00 },
> + .con0_for_pcie = { 0x0000, 15, 0, 0x00, 0x1000 },
> + .con1_for_pcie = { 0x0004, 15, 0, 0x00, 0x0000 },
> + .con2_for_pcie = { 0x0008, 15, 0, 0x00, 0x0101 },
> + .con3_for_pcie = { 0x000c, 15, 0, 0x00, 0x0200 },
> + .con0_for_sata = { 0x0000, 15, 0, 0x00, 0x0119 },
> + .con1_for_sata = { 0x0004, 15, 0, 0x00, 0x0040 },
> + .con2_for_sata = { 0x0008, 15, 0, 0x00, 0x80c3 },
> + .con3_for_sata = { 0x000c, 15, 0, 0x00, 0x4407 },
> + /* pipe-grf */
> + .pipe_con0_for_sata = { 0x0000, 15, 0, 0x00, 0x2220 },
> + .pipe_sgmii_mac_sel = { 0x0040, 1, 1, 0x00, 0x01 },
> + .pipe_xpcs_phy_ready = { 0x0040, 2, 2, 0x00, 0x01 },
> + .u3otg0_port_en = { 0x0104, 15, 0, 0x0181, 0x1100 },
> + .u3otg1_port_en = { 0x0144, 15, 0, 0x0181, 0x1100 },
> +};
> +
> +static const struct rockchip_combphy_cfg rk3568_combphy_cfgs = {
> + .grfcfg = &rk3568_combphy_grfcfgs,
> + .combphy_cfg = rk3568_combphy_cfg,
> +};
> +
> +static const struct of_device_id rockchip_combphy_of_match[] = {
> + {
> + .compatible = "rockchip,rk3568-naneng-combphy",
> + .data = &rk3568_combphy_cfgs,
> + },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, rockchip_combphy_of_match);
> +
> +static struct platform_driver rockchip_combphy_driver = {
> + .probe = rockchip_combphy_probe,
> + .driver = {
> + .name = "rockchip-naneng-combphy",
> + .of_match_table = rockchip_combphy_of_match,
> + },
> +};
> +module_platform_driver(rockchip_combphy_driver);
> +
> +MODULE_DESCRIPTION("Rockchip NANENG COMBPHY driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.20.1
--
~Vinod
More information about the linux-phy
mailing list