[PATCH v2 2/6] PCI: qcom: add support for IPQ60xx PCIe controller
Rob Herring
robh+dt at kernel.org
Fri Aug 6 12:59:44 PDT 2021
On Wed, May 5, 2021 at 3:18 AM Baruch Siach <baruch at tkos.co.il> wrote:
>
> From: Selvam Sathappan Periakaruppan <speriaka at codeaurora.org>
>
> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
> platform.
>
> The code is based on downstream Codeaurora kernel v5.4. Split out the
> DBI registers access part from .init into .post_init. DBI registers are
> only accessible after phy_power_on().
>
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka at codeaurora.org>
> Signed-off-by: Baruch Siach <baruch at tkos.co.il>
> ---
> v2:
> * Drop ATU configuration; rely on common code instead
>
> * Use more common register macros
>
> * Use bulk clk and reset APIs
> ---
> drivers/pci/controller/dwc/pcie-designware.h | 1 +
> drivers/pci/controller/dwc/pcie-qcom.c | 150 +++++++++++++++++++
> 2 files changed, 151 insertions(+)
>
> diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
> index ceb359b6e6a6..346462c74a3e 100644
> --- a/drivers/pci/controller/dwc/pcie-designware.h
> +++ b/drivers/pci/controller/dwc/pcie-designware.h
> @@ -76,6 +76,7 @@
>
> #define GEN3_RELATED_OFF 0x890
> #define GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL BIT(0)
> +#define GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS BIT(13)
> #define GEN3_RELATED_OFF_GEN3_EQ_DISABLE BIT(16)
> #define GEN3_RELATED_OFF_RATE_SHADOW_SEL_SHIFT 24
> #define GEN3_RELATED_OFF_RATE_SHADOW_SEL_MASK GENMASK(25, 24)
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index 8a7a300163e5..93766aee3e7c 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -52,6 +52,10 @@
> #define PCIE20_PARF_DBI_BASE_ADDR 0x168
> #define PCIE20_PARF_SLV_ADDR_SPACE_SIZE 0x16C
> #define PCIE20_PARF_MHI_CLOCK_RESET_CTRL 0x174
> +#define AHB_CLK_EN BIT(0)
> +#define MSTR_AXI_CLK_EN BIT(1)
> +#define BYPASS BIT(4)
> +
> #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT 0x178
> #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 0x1A8
> #define PCIE20_PARF_LTSSM 0x1B0
> @@ -94,6 +98,12 @@
> #define SLV_ADDR_SPACE_SZ 0x10000000
>
> #define PCIE20_LNK_CONTROL2_LINK_STATUS2 0xa0
> +#define PCIE_CAP_CURR_DEEMPHASIS BIT(16)
Isn't this a standard register field?
> +#define SPEED_GEN1 0x1
> +#define SPEED_GEN2 0x2
> +#define SPEED_GEN3 0x3
And these?
There's already some common DWC code for setting the link speed.
> +#define AXI_CLK_RATE 200000000
> +#define RCHNG_CLK_RATE 100000000
>
> #define DEVICE_TYPE_RC 0x4
>
> @@ -168,6 +178,11 @@ struct qcom_pcie_resources_2_7_0 {
> struct clk *pipe_clk;
> };
>
> +struct qcom_pcie_resources_2_9_0 {
> + struct clk_bulk_data clks[5];
> + struct reset_control *rst;
> +};
> +
> union qcom_pcie_resources {
> struct qcom_pcie_resources_1_0_0 v1_0_0;
> struct qcom_pcie_resources_2_1_0 v2_1_0;
> @@ -175,6 +190,7 @@ union qcom_pcie_resources {
> struct qcom_pcie_resources_2_3_3 v2_3_3;
> struct qcom_pcie_resources_2_4_0 v2_4_0;
> struct qcom_pcie_resources_2_7_0 v2_7_0;
> + struct qcom_pcie_resources_2_9_0 v2_9_0;
> };
>
> struct qcom_pcie;
> @@ -1266,6 +1282,130 @@ static void qcom_pcie_post_deinit_2_7_0(struct qcom_pcie *pcie)
> clk_disable_unprepare(res->pipe_clk);
> }
>
> +static int qcom_pcie_get_resources_2_9_0(struct qcom_pcie *pcie)
> +{
> + struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> + struct dw_pcie *pci = pcie->pci;
> + struct device *dev = pci->dev;
> + int ret;
> +
> + res->clks[0].id = "iface";
> + res->clks[1].id = "axi_m";
> + res->clks[2].id = "axi_s";
> + res->clks[3].id = "axi_bridge";
> + res->clks[4].id = "rchng";
> +
> + ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
> + if (ret < 0)
> + return ret;
> +
> + res->rst = devm_reset_control_array_get_exclusive(dev);
> + if (IS_ERR(res->rst))
> + return PTR_ERR(res->rst);
> +
> + return 0;
> +}
> +
> +static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
> +{
> + struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> +
> + clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> +}
> +
> +static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
> +{
> + struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> + struct device *dev = pcie->pci->dev;
> + int ret;
> +
> + ret = reset_control_assert(res->rst);
> + if (ret) {
> + dev_err(dev, "reset assert failed (%d)\n", ret);
> + return ret;
> + }
> +
> + usleep_range(2000, 2500);
> +
> + ret = reset_control_deassert(res->rst);
> + if (ret) {
> + dev_err(dev, "reset deassert failed (%d)\n", ret);
> + return ret;
> + }
> +
> + /*
> + * Don't have a way to see if the reset has completed.
> + * Wait for some time.
> + */
> + usleep_range(2000, 2500);
> +
> + ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> + if (ret)
> + goto err_reset;
> +
> + return 0;
> +
> + /*
> + * Not checking for failure, will anyway return
> + * the original failure in 'ret'.
> + */
> +err_reset:
> + reset_control_assert(res->rst);
> +
> + return ret;
> +}
> +
> +static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
> +{
> + struct dw_pcie *pci = pcie->pci;
> + u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
> + u32 val;
> + int i;
> +
> + writel(SLV_ADDR_SPACE_SZ,
> + pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
> +
> + val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
> + val &= ~BIT(0);
> + writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
> +
> + writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
> +
> + writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
> + writel(BYPASS | MSTR_AXI_CLK_EN | AHB_CLK_EN,
> + pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
> + writel(GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS
> + | GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL,
> + pci->dbi_base + GEN3_RELATED_OFF);
> +
> + writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS
> + | SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS |
> + AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS,
> + pcie->parf + PCIE20_PARF_SYS_CTRL);
> +
> + writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
> +
> + dw_pcie_dbi_ro_wr_en(pci);
> + writel(PCIE_CAP_LINK1_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
> +
> + /* Configure PCIe link capabilities for ASPM */
> + val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP);
> + val &= ~PCI_EXP_LNKCAP_ASPMS;
> + writel(val, pci->dbi_base + offset + PCI_EXP_LNKCAP);
> +
> + writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base + offset +
> + PCI_EXP_DEVCTL2);
> +
> + writel(PCIE_CAP_CURR_DEEMPHASIS | SPEED_GEN3,
> + pci->dbi_base + offset + PCI_EXP_DEVCTL2);
Doesn't this overwrite the prior register write?
> +
> + for (i = 0;i < 256;i++)
> + writel(0x0, pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N
> + + (4 * i));
> +
> + return 0;
> +}
> +
> static int qcom_pcie_link_up(struct dw_pcie *pci)
> {
> u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
> @@ -1456,6 +1596,15 @@ static const struct qcom_pcie_ops ops_1_9_0 = {
> .config_sid = qcom_pcie_config_sid_sm8250,
> };
>
> +/* Qcom IP rev.: 2.9.0 Synopsys IP rev.: 5.00a */
> +static const struct qcom_pcie_ops ops_2_9_0 = {
> + .get_resources = qcom_pcie_get_resources_2_9_0,
> + .init = qcom_pcie_init_2_9_0,
> + .post_init = qcom_pcie_post_init_2_9_0,
> + .deinit = qcom_pcie_deinit_2_9_0,
> + .ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
> +};
> +
> static const struct dw_pcie_ops dw_pcie_ops = {
> .link_up = qcom_pcie_link_up,
> .start_link = qcom_pcie_start_link,
> @@ -1555,6 +1704,7 @@ static const struct of_device_id qcom_pcie_match[] = {
> { .compatible = "qcom,pcie-qcs404", .data = &ops_2_4_0 },
> { .compatible = "qcom,pcie-sdm845", .data = &ops_2_7_0 },
> { .compatible = "qcom,pcie-sm8250", .data = &ops_1_9_0 },
> + { .compatible = "qcom,pcie-ipq6018", .data = &ops_2_9_0 },
> { }
> };
>
> --
> 2.30.2
>
More information about the linux-phy
mailing list