acpi=off pci=biosirq irqfixup SLOT2

Cyrille Grinner cyrille at grinner.fr
Tue Mar 23 15:52:47 EDT 2010


[    1.478062] device-mapper: uevent: version 1.0.3
[    1.478808] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised:

dm-devel at redhat.com
[    1.479474] device-mapper: multipath: version 1.1.0 loaded
[    1.479570] device-mapper: multipath round-robin: version 1.0.0 loaded
[    1.480568] EISA: Probing bus 0 at eisa.0
[    1.480665] Cannot allocate resource for EISA slot 1
[    1.480738] Cannot allocate resource for EISA slot 2
[    1.480809] Cannot allocate resource for EISA slot 3
[    1.480908] EISA: Detected 0 cards.
[    1.481311] cpuidle: using governor ladder
[    1.481391] cpuidle: using governor menu
[    1.484101] TCP cubic registered
[    1.484967] NET: Registered protocol family 10
[    1.487047] lo: Disabled Privacy Extensions
[    1.488655] NET: Registered protocol family 17
[    1.488841] Bluetooth: L2CAP ver 2.13
[    1.488909] Bluetooth: L2CAP socket layer initialized
[    1.488983] Bluetooth: SCO (Voice Link) ver 0.6
[    1.489051] Bluetooth: SCO socket layer initialized
[    1.489313] Bluetooth: RFCOMM TTY layer initialized
[    1.489394] Bluetooth: RFCOMM socket layer initialized
[    1.489465] Bluetooth: RFCOMM ver 1.11
[    1.489573] Using IPI No-Shortcut mode
[    1.489995] PM: Resume from disk failed.
[    1.490049] registered taskstats version 1
[    1.490475]   Magic number: 2:413:650
[    1.490689] rtc_cmos 00:05: setting system clock to 2010-03-23 20:37:46

UTC (1269376666)
[    1.490788] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.490859] EDD information not available.
[    1.507744] input: AT Translated Set 2 keyboard as

/devices/platform/i8042/serio0/input/input1
[    1.632575] ata2.00: ATAPI: HL-DT-ST DVDRAM GMA-4082N, HJ02,

max UDMA/33
[    1.633437] ata1.00: ATA-5: FUJITSU MHM2100AT, 5823, max

UDMA/66
[    1.633521] ata1.00: 19640880 sectors, multi 16: LBA
[    1.648396] ata2.00: configured for UDMA/33
[    1.649098] ata1.00: configured for UDMA/66
[    1.649787] scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHM2100A

5823 PQ: 0 ANSI: 5
[    1.650593] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.650909] sd 0:0:0:0: [sda] 19640880 512-byte logical blocks: (10.0

GB/9.36 GiB)
[    1.651261] sd 0:0:0:0: [sda] Write Protect is off
[    1.651340] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.651481] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,

doesn't support DPO or FUA
[    1.652307]  sda:
[    1.656515] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GMA-4082N

HJ02 PQ: 0 ANSI: 5
[    1.668523] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw

xa/form2 cdda tray
[    1.668633] Uniform CD-ROM driver Revision: 3.20
[    1.669110] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.669358] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.670834]  sda1 < sda5 sda6 > sda3
[    1.693480] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.693644] Freeing unused kernel memory: 540k freed
[    1.697428] Write protecting the kernel text: 4568k
[    1.697676] Write protecting the kernel read-only data: 1836k
[    1.784051] usb 1-2: new full speed USB device using uhci_hcd and 
address

2
[    2.110574] usb 1-2: configuration #1 chosen from 1 choice
[    2.572160] Linux agpgart interface v0.103
[    2.905010] agpgart-intel 0000:00:00.0: Intel i815 Chipset
[    3.070808] agpgart-intel 0000:00:00.0: AGP aperture is 64M @

0xf8000000
[    3.176764] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10]  

MMIO=[f4104000-f41047ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[    4.270299] PM: Starting manual resume from disk
[    4.270397] PM: Resume from partition 8:6
[    4.270405] PM: Checking hibernation image.
[    4.270934] PM: Resume from disk failed.
[    4.346555] kjournald starting.  Commit interval 5 seconds
[    4.346700] EXT3-fs: mounted filesystem with writeback data mode.
[    4.452392] ieee1394: Host added: ID:BUS[0-00:1023]  

GUID[0800460300a53ece]
[    5.955923] type=1505 audit(1269376670.965:2):

operation="profile_load" pid=298

name=/usr/share/gdm/guest-session/Xsession
[    6.031994] type=1505 audit(1269376671.041:3): operation="profile_load"

pid=299 name=/sbin/dhclient3
[    6.034135] type=1505 audit(1269376671.041:4): operation="profile_load"

pid=299 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[    6.035318] type=1505 audit(1269376671.041:5): operation="profile_load"

pid=299 name=/usr/lib/connman/scripts/dhclient-script
[    6.143674] type=1505 audit(1269376671.149:6): operation="profile_load"

pid=300 name=/usr/bin/evince
[    6.178958] type=1505 audit(1269376671.185:7): operation="profile_load"

pid=300 name=/usr/bin/evince-previewer
[    6.202090] type=1505 audit(1269376671.209:8):

operation="profile_load" pid=300 name=/usr/bin/evince-thumbnailer
[    6.285969] type=1505 audit(1269376671.293:9):

operation="profile_load" pid=302 name=/usr/lib/cups/backend/cups-pdf
[    6.288713] type=1505 audit(1269376671.297:10):

operation="profile_load" pid=302 name=/usr/sbin/cupsd
[    6.311426] type=1505 audit(1269376671.317:11): operation="profile_load"

pid=303 name=/usr/sbin/tcpdump
[    8.593422] Adding 546168k swap on /dev/sda6.  Priority:-1 extents:1

across:546168k
[    9.472767] EXT3 FS on sda5, internal journal
[   12.417836] udev: starting version 147
[   15.131750] cfg80211: Calling CRDA to update world regulatory domain
[   15.676077] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   16.225996] Intel 82802 RNG detected
[   16.818671] lp: driver loaded but no devices found
[   17.128084] input: PS/2 Mouse as

/devices/platform/i8042/serio1/input/input2
[   17.164891] input: AlpsPS/2 ALPS GlidePoint as

/devices/platform/i8042/serio1/input/input3
[   18.153465] yenta_cardbus 0000:01:02.0: CardBus bridge found

[104d:80df]
[   18.153507] yenta_cardbus 0000:01:02.0: no PCI IRQ, CardBus support

disabled for this socket.
[   18.153520] yenta_cardbus 0000:01:02.0: check your BIOS CardBus,

BIOS IRQ or ACPI settings.
[   18.280324] yenta_cardbus 0000:01:02.0: ISA IRQ mask 0x0098, PCI irq

0
[   18.280341] yenta_cardbus 0000:01:02.0: Socket status: 30000826
[   18.280355] pci_bus 0000:01: Raising subordinate bus# of parent bus

(#01) from #01 to #05
[   18.280386] yenta_cardbus 0000:01:02.0: pcmcia: parent PCI bridge I/O

window: 0x3000 - 0x3fff
[   18.280403] pcmcia_socket pcmcia_socket0: cs: IO port probe

0x3000-0x3fff: clean.
[   18.281125] yenta_cardbus 0000:01:02.0: pcmcia: parent PCI bridge

Memory window: 0xf4100000 - 0xf41fffff
[   18.281139] yenta_cardbus 0000:01:02.0: pcmcia: parent PCI bridge

Memory window: 0x20000000 - 0x27ffffff
[   18.281677] yenta_cardbus 0000:01:02.1: CardBus bridge found

[104d:80df]
[   18.281716] yenta_cardbus 0000:01:02.1: no PCI IRQ, CardBus support

disabled for this socket.
[   18.281728] yenta_cardbus 0000:01:02.1: check your BIOS CardBus, BIOS

IRQ or ACPI settings.
[   18.420102] yenta_cardbus 0000:01:02.1: ISA IRQ mask 0x00b8, PCI irq

0
[   18.420120] yenta_cardbus 0000:01:02.1: Socket status: 30000820
[   18.420136] pci_bus 0000:01: Raising subordinate bus# of parent bus

(#01) from #05 to #09
[   18.420168] yenta_cardbus 0000:01:02.1: pcmcia: parent PCI bridge I/O

window: 0x3000 - 0x3fff
[   18.420184] pcmcia_socket pcmcia_socket1: cs: IO port probe

0x3000-0x3fff: clean.
[   18.420907] yenta_cardbus 0000:01:02.1: pcmcia: parent PCI bridge

Memory window: 0xf4100000 - 0xf41fffff
[   18.420924] yenta_cardbus 0000:01:02.1: pcmcia: parent PCI bridge

Memory window: 0x20000000 - 0x27ffffff
[   18.571588] pcmcia_socket pcmcia_socket1: cs: cardbus cards are not

supported.
[   19.180326] cfg80211: World regulatory domain updated:
[   19.180344]  (start_freq - end_freq @ bandwidth), (max_antenna_gain,

max_eirp)
[   19.180359]  (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,

2000 mBm)
[   19.180372]  (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi,

2000 mBm)
[   19.180384]  (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,

2000 mBm)
[   19.180397]  (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,

2000 mBm)
[   19.180409]  (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,

2000 mBm)
[   19.540142] pcmcia_socket pcmcia_socket0: cs: IO port probe

0x100-0x3af: clean.
[   19.542300] pcmcia_socket pcmcia_socket0: cs: IO port probe

0x3e0-0x4ff: clean.
[   19.543310] pcmcia_socket pcmcia_socket0: cs: IO port probe

0x820-0x8ff: clean.
[   19.546687] pcmcia_socket pcmcia_socket0: cs: IO port probe

0xc00-0xcf7: clean.
[   19.548313] pcmcia_socket pcmcia_socket0: cs: IO port probe

0xa00-0xaff: clean.
[   19.732830] ip_tables: (C) 2000-2006 Netfilter Core Team
[   19.813279] pcmcia_socket pcmcia_socket1: cs: IO port probe

0x100-0x3af: clean.
[   19.815374] pcmcia_socket pcmcia_socket1: cs: IO port probe

0x3e0-0x4ff: clean.
[   19.816515] pcmcia_socket pcmcia_socket1: cs: IO port probe

0x820-0x8ff: clean.
[   19.817359] pcmcia_socket pcmcia_socket1: cs: IO port probe

0xc00-0xcf7: clean.
[   19.818850] pcmcia_socket pcmcia_socket1: cs: IO port probe

0xa00-0xaff: clean.
[   21.739095] type=1505 audit(1269373086.744:12):

operation="profile_replace" pid=633

name=/usr/share/gdm/guest-session/Xsession
[   21.751395] type=1505 audit(1269373086.756:13):

operation="profile_replace" pid=634 name=/sbin/dhclient3
[   21.755070] type=1505 audit(1269373086.760:14):

operation="profile_replace" pid=634

name=/usr/lib/NetworkManager/nm-dhcp-client.action
[   21.756378] type=1505 audit(1269373086.764:15):

operation="profile_replace" pid=634

name=/usr/lib/connman/scripts/dhclient-script
[   21.790542] type=1505 audit(1269373086.796:16):

operation="profile_replace" pid=635 name=/usr/bin/evince
[   21.852864] type=1505 audit(1269373086.860:17):

operation="profile_replace" pid=635 name=/usr/bin/evince-previewer
[   21.889159] type=1505 audit(1269373086.896:18):

operation="profile_replace" pid=635 name=/usr/bin/evince-thumbnailer
[   21.922727] type=1505 audit(1269373086.928:19):

operation="profile_replace" pid=647

name=/usr/lib/cups/backend/cups-pdf
[   21.927570] type=1505 audit(1269373086.932:20):

operation="profile_replace" pid=647 name=/usr/sbin/cupsd
[   21.937971] type=1505 audit(1269373086.944:21):

operation="profile_replace" pid=648 name=/usr/sbin/tcpdump
[   22.099068] phy0: Selected rate control algorithm 'minstrel'
[   22.102200] Registered led device: rt73usb-phy0::radio
[   22.102286] Registered led device: rt73usb-phy0::assoc
[   22.102361] Registered led device: rt73usb-phy0::quality
[   22.106494] usbcore: registered new interface driver rt73usb
[   24.520216] Intel ICH 0000:00:1f.5: found PCI INT B -> IRQ 5
[   24.520268] Intel ICH 0000:00:1f.5: sharing IRQ 5 with 0000:00:1f.3
[   24.520292] Intel ICH 0000:00:1f.5: sharing IRQ 5 with 0000:00:1f.6
[   24.520374] Intel ICH 0000:00:1f.5: setting latency timer to 64
[   24.943502] intel8x0_measure_ac97_clock: measured 58907 usecs (2832

samples)
[   24.943518] intel8x0: clocking to 48000
[   33.073874] rt73usb 1-2:1.0: firmware: requesting rt73.bin
[   33.862442] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   39.007540] [drm] Initialized drm 1.1.0 20060810
[   39.082874] PCI: setting IRQ 10 as level-triggered
[   39.082895] pci 0000:00:02.0: found PCI INT A -> IRQ 10
[   39.082965] pci 0000:00:02.0: setting latency timer to 64
[   39.089314] [drm] Initialized i810 1.4.0 20030605 for 0000:00:02.0 on

minor 0
[   39.101105] mtrr: base(0xf8000000) is not aligned on a size(0x12c000)

boundary
[   39.343197] [drm] Using v1.4 init.
[   39.485208] ppdev: user-space parallel port driver
[   42.993991] [drm:drm_reclaim_locked_buffers] *ERROR*

reclaim_buffers_locked() deadlock. Please rework this
[   42.994006]  driver to use reclaim_buffers_idlelocked() instead.
[   42.994012]  I will go on reclaiming the buffers anyway.
[  222.971995] wlan0: authenticate with AP ce:3d:6a:0b:95:f8
[  222.974350] wlan0: authenticated
[  222.974418] wlan0: associate with AP ce:3d:6a:0b:95:f8
[  222.982407] wlan0: RX AssocResp from ce:3d:6a:0b:95:f8 (capab=0x411

status=0 aid=1)
[  222.982426] wlan0: associated
[  223.187360] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready




More information about the linux-pcmcia mailing list