[PATCH 6/6] Alchemy: XXS1500 PCMCIA driver rewrite
Manuel Lauss
manuel.lauss at googlemail.com
Sun Oct 4 08:55:29 EDT 2009
Rewritten XXS1500 PCMCIA socket driver, standalone (doesn't
depend on au1000_generic.c) and added carddetect IRQ support.
Cc: Florian Fainelli <florian at openwrt.org>
Cc: Linux-PCMCIA <linux-pcmcia at lists.infradead.org>
Signed-off-by: Manuel Lauss <manuel.lauss at gmail.com>
---
Compile-tested only; I don't have hardware to test,
CC'ing Florian, he might still have one.
V2: this one depends on the previous db1xxx_ss.c patch to apply
cleanly; no other changes.
arch/mips/alchemy/xxs1500/Makefile | 2 +-
arch/mips/alchemy/xxs1500/board_setup.c | 16 --
arch/mips/alchemy/xxs1500/platform.c | 63 ++++++
drivers/pcmcia/Kconfig | 10 +
drivers/pcmcia/Makefile | 3 +-
drivers/pcmcia/au1000_xxs1500.c | 188 ----------------
drivers/pcmcia/xxs1500_ss.c | 357 +++++++++++++++++++++++++++++++
7 files changed, 433 insertions(+), 206 deletions(-)
create mode 100644 arch/mips/alchemy/xxs1500/platform.c
delete mode 100644 drivers/pcmcia/au1000_xxs1500.c
create mode 100644 drivers/pcmcia/xxs1500_ss.c
diff --git a/arch/mips/alchemy/xxs1500/Makefile b/arch/mips/alchemy/xxs1500/Makefile
index 545d8f5..68671c2 100644
--- a/arch/mips/alchemy/xxs1500/Makefile
+++ b/arch/mips/alchemy/xxs1500/Makefile
@@ -5,4 +5,4 @@
# Makefile for MyCable XXS1500 board.
#
-lib-y := init.o board_setup.o
+lib-y := init.o board_setup.o platform.o
diff --git a/arch/mips/alchemy/xxs1500/board_setup.c b/arch/mips/alchemy/xxs1500/board_setup.c
index cad14f8..eb31350 100644
--- a/arch/mips/alchemy/xxs1500/board_setup.c
+++ b/arch/mips/alchemy/xxs1500/board_setup.c
@@ -69,22 +69,6 @@ void __init board_setup(void)
/* Enable DTR = USB power up */
au_writel(0x01, UART3_ADDR + UART_MCR); /* UART_MCR_DTR is 0x01??? */
-#ifdef CONFIG_PCMCIA_XXS1500
- /* GPIO 0, 1, and 4 are inputs */
- alchemy_gpio_direction_input(0);
- alchemy_gpio_direction_input(1);
- alchemy_gpio_direction_input(4);
-
- /* GPIO2 208/9/10/11 are inputs */
- alchemy_gpio_direction_input(208);
- alchemy_gpio_direction_input(209);
- alchemy_gpio_direction_input(210);
- alchemy_gpio_direction_input(211);
-
- /* Turn off power */
- alchemy_gpio_direction_output(214, 0);
-#endif
-
#ifdef CONFIG_PCI
#if defined(__MIPSEB__)
au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
diff --git a/arch/mips/alchemy/xxs1500/platform.c b/arch/mips/alchemy/xxs1500/platform.c
new file mode 100644
index 0000000..c14dcaa
--- /dev/null
+++ b/arch/mips/alchemy/xxs1500/platform.c
@@ -0,0 +1,63 @@
+/*
+ * XXS1500 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-au1x00/au1000.h>
+
+static struct resource xxs1500_pcmcia_res[] = {
+ {
+ .name = "pseudo-io",
+ .flags = IORESOURCE_MEM,
+ .start = PCMCIA_IO_PSEUDO_PHYS,
+ .end = PCMCIA_IO_PSEUDO_PHYS + 0x00040000 - 1,
+ },
+ {
+ .name = "pseudo-attr",
+ .flags = IORESOURCE_MEM,
+ .start = PCMCIA_ATTR_PSEUDO_PHYS,
+ .end = PCMCIA_ATTR_PSEUDO_PHYS + 0x00040000 - 1,
+ },
+ {
+ .name = "pseudo-mem",
+ .flags = IORESOURCE_MEM,
+ .start = PCMCIA_IO_PSEUDO_PHYS,
+ .end = PCMCIA_IO_PSEUDO_PHYS + 0x00040000 - 1,
+ },
+};
+
+static struct platform_device xxs1500_pcmcia_dev = {
+ .name = "xxs1500_pcmcia",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(xxs1500_pcmcia_res),
+ .resource = xxs1500_pcmcia_res,
+};
+
+static struct platform_device *xxs1500_devs[] __initdata = {
+ &xxs1500_pcmcia_dev,
+};
+
+static int __init xxs1500_dev_init(void)
+{
+ return platform_add_devices(xxs1500_devs,
+ ARRAY_SIZE(xxs1500_devs));
+}
+device_initcall(xxs1500_dev_init);
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index 22f6814..5ed3b93 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -203,6 +203,16 @@ config PCMCIA_ALCHEMY_DEVBOARD
This driver is also available as a module called db1xxx_ss.ko
+config PCMCIA_XXS1500
+ tristate "MyCable XXS1500 PCMCIA socket support"
+ depends on PCMCIA && MIPS_XXS1500
+ select 64BIT_PHYS_ADDR
+ help
+ Support for the PCMCIA/CF socket interface on MyCable XXS1500
+ systems.
+
+ This driver is also available as a module called xxs1500_ss.ko
+
config PCMCIA_BCM63XX
tristate "bcm63xx pcmcia support"
depends on BCM63XX && PCMCIA
diff --git a/drivers/pcmcia/Makefile b/drivers/pcmcia/Makefile
index e58d162..8bd8b02 100644
--- a/drivers/pcmcia/Makefile
+++ b/drivers/pcmcia/Makefile
@@ -41,7 +41,6 @@ pxa2xx_core-y += soc_common.o pxa2xx_base.o
au1x00_ss-y += au1000_generic.o
au1x00_ss-$(CONFIG_MIPS_PB1000) += au1000_pb1x00.o
-au1x00_ss-$(CONFIG_MIPS_XXS1500) += au1000_xxs1500.o
sa1111_cs-y += sa1111_generic.o
sa1111_cs-$(CONFIG_ASSABET_NEPONSET) += sa1100_neponset.o
@@ -71,3 +70,5 @@ pxa2xx-obj-$(CONFIG_MACH_E740) += pxa2xx_e740.o
pxa2xx-obj-$(CONFIG_MACH_STARGATE2) += pxa2xx_stargate2.o
obj-$(CONFIG_PCMCIA_PXA2XX) += pxa2xx_core.o $(pxa2xx-obj-y)
+
+obj-$(CONFIG_PCMCIA_XXS1500) += xxs1500_ss.o
diff --git a/drivers/pcmcia/au1000_xxs1500.c b/drivers/pcmcia/au1000_xxs1500.c
deleted file mode 100644
index b43d47b..0000000
--- a/drivers/pcmcia/au1000_xxs1500.c
+++ /dev/null
@@ -1,188 +0,0 @@
-/*
- *
- * MyCable board specific pcmcia routines.
- *
- * Copyright 2003 MontaVista Software Inc.
- * Author: Pete Popov, MontaVista Software, Inc.
- * ppopov at mvista.com or source at mvista.com
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/ioport.h>
-#include <linux/kernel.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/proc_fs.h>
-#include <linux/types.h>
-
-#include <pcmcia/cs_types.h>
-#include <pcmcia/cs.h>
-#include <pcmcia/ss.h>
-#include <pcmcia/cistpl.h>
-#include <pcmcia/bus_ops.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-
-#include <asm/au1000.h>
-#include <asm/au1000_pcmcia.h>
-
-#define PCMCIA_MAX_SOCK 0
-#define PCMCIA_NUM_SOCKS (PCMCIA_MAX_SOCK + 1)
-#define PCMCIA_IRQ AU1000_GPIO_4
-
-#if 0
-#define DEBUG(x, args...) printk(__func__ ": " x, ##args)
-#else
-#define DEBUG(x,args...)
-#endif
-
-static int xxs1500_pcmcia_init(struct pcmcia_init *init)
-{
- return PCMCIA_NUM_SOCKS;
-}
-
-static int xxs1500_pcmcia_shutdown(void)
-{
- /* turn off power */
- au_writel(au_readl(GPIO2_PINSTATE) | (1<<14)|(1<<30),
- GPIO2_OUTPUT);
- au_sync_delay(100);
-
- /* assert reset */
- au_writel(au_readl(GPIO2_PINSTATE) | (1<<4)|(1<<20),
- GPIO2_OUTPUT);
- au_sync_delay(100);
- return 0;
-}
-
-
-static int
-xxs1500_pcmcia_socket_state(unsigned sock, struct pcmcia_state *state)
-{
- u32 inserted; u32 vs;
- unsigned long gpio, gpio2;
-
- if(sock > PCMCIA_MAX_SOCK) return -1;
-
- gpio = au_readl(SYS_PINSTATERD);
- gpio2 = au_readl(GPIO2_PINSTATE);
-
- vs = gpio2 & ((1<<8) | (1<<9));
- inserted = (!(gpio & 0x1) && !(gpio & 0x2));
-
- state->ready = 0;
- state->vs_Xv = 0;
- state->vs_3v = 0;
- state->detect = 0;
-
- if (inserted) {
- switch (vs) {
- case 0:
- case 1:
- case 2:
- state->vs_3v=1;
- break;
- case 3: /* 5V */
- default:
- /* return without setting 'detect' */
- printk(KERN_ERR "au1x00_cs: unsupported VS\n",
- vs);
- return;
- }
- state->detect = 1;
- }
-
- if (state->detect) {
- state->ready = 1;
- }
-
- state->bvd1= gpio2 & (1<<10);
- state->bvd2 = gpio2 & (1<<11);
- state->wrprot=0;
- return 1;
-}
-
-
-static int xxs1500_pcmcia_get_irq_info(struct pcmcia_irq_info *info)
-{
-
- if(info->sock > PCMCIA_MAX_SOCK) return -1;
- info->irq = PCMCIA_IRQ;
- return 0;
-}
-
-
-static int
-xxs1500_pcmcia_configure_socket(const struct pcmcia_configure *configure)
-{
-
- if(configure->sock > PCMCIA_MAX_SOCK) return -1;
-
- DEBUG("Vcc %dV Vpp %dV, reset %d\n",
- configure->vcc, configure->vpp, configure->reset);
-
- switch(configure->vcc){
- case 33: /* Vcc 3.3V */
- /* turn on power */
- DEBUG("turn on power\n");
- au_writel((au_readl(GPIO2_PINSTATE) & ~(1<<14))|(1<<30),
- GPIO2_OUTPUT);
- au_sync_delay(100);
- break;
- case 50: /* Vcc 5V */
- default: /* what's this ? */
- printk(KERN_ERR "au1x00_cs: unsupported VCC\n");
- case 0: /* Vcc 0 */
- /* turn off power */
- au_sync_delay(100);
- au_writel(au_readl(GPIO2_PINSTATE) | (1<<14)|(1<<30),
- GPIO2_OUTPUT);
- break;
- }
-
- if (!configure->reset) {
- DEBUG("deassert reset\n");
- au_writel((au_readl(GPIO2_PINSTATE) & ~(1<<4))|(1<<20),
- GPIO2_OUTPUT);
- au_sync_delay(100);
- au_writel((au_readl(GPIO2_PINSTATE) & ~(1<<5))|(1<<21),
- GPIO2_OUTPUT);
- }
- else {
- DEBUG("assert reset\n");
- au_writel(au_readl(GPIO2_PINSTATE) | (1<<4)|(1<<20),
- GPIO2_OUTPUT);
- }
- au_sync_delay(100);
- return 0;
-}
-
-struct pcmcia_low_level xxs1500_pcmcia_ops = {
- xxs1500_pcmcia_init,
- xxs1500_pcmcia_shutdown,
- xxs1500_pcmcia_socket_state,
- xxs1500_pcmcia_get_irq_info,
- xxs1500_pcmcia_configure_socket
-};
diff --git a/drivers/pcmcia/xxs1500_ss.c b/drivers/pcmcia/xxs1500_ss.c
new file mode 100644
index 0000000..4e36930
--- /dev/null
+++ b/drivers/pcmcia/xxs1500_ss.c
@@ -0,0 +1,357 @@
+/*
+ * PCMCIA socket code for the MyCable XXS1500 system.
+ *
+ * Copyright (c) 2009 Manuel Lauss <manuel.lauss at gmail.com>
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/mm.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/resource.h>
+#include <linux/spinlock.h>
+
+#include <pcmcia/cs_types.h>
+#include <pcmcia/cs.h>
+#include <pcmcia/ss.h>
+#include <pcmcia/cistpl.h>
+
+#include <asm/irq.h>
+#include <asm/system.h>
+#include <asm/mach-au1x00/au1000.h>
+
+#define MEM_MAP_SIZE 0x400000
+#define IO_MAP_SIZE 0x1000
+
+
+/*
+ * 3.3V cards only; all interfacing is done via gpios:
+ *
+ * 0/1: carddetect (00 = card present, xx = huh)
+ * 4: card irq
+ * 204: reset (high-act)
+ * 205: buffer enable (low-act)
+ * 208/209: card voltage key (00,01,10,11)
+ * 210: battwarn
+ * 211: batdead
+ * 214: power (low-act)
+ */
+#define GPIO_CDA 0
+#define GPIO_CDB 1
+#define GPIO_CARDIRQ 4
+#define GPIO_RESET 204
+#define GPIO_OUTEN 205
+#define GPIO_VSL 208
+#define GPIO_VSH 209
+#define GPIO_BATTDEAD 210
+#define GPIO_BATTWARN 211
+#define GPIO_POWER 214
+
+struct xxs1500_pcmcia_sock {
+ struct pcmcia_socket socket;
+ void *virt_io;
+
+ /* the "pseudo" addresses of the PCMCIA space. */
+ unsigned long phys_io;
+ unsigned long phys_attr;
+ unsigned long phys_mem;
+
+ /* previous flags for set_socket() */
+ unsigned int old_flags;
+};
+
+#define to_xxs_socket(x) container_of(x, struct xxs1500_pcmcia_sock, socket)
+
+static irqreturn_t cdirq(int irq, void *data)
+{
+ struct xxs1500_pcmcia_sock *sock = data;
+
+ pcmcia_parse_events(&sock->socket, SS_DETECT);
+
+ return IRQ_HANDLED;
+}
+
+static int xxs1500_pcmcia_configure(struct pcmcia_socket *skt,
+ struct socket_state_t *state)
+{
+ struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
+ unsigned int changed;
+
+ /* power control */
+ switch (state->Vcc) {
+ case 0:
+ gpio_set_value(GPIO_POWER, 1); /* power off */
+ break;
+ case 33:
+ gpio_set_value(GPIO_POWER, 0); /* power on */
+ break;
+ case 50:
+ default:
+ return -EINVAL;
+ }
+
+ changed = state->flags ^ sock->old_flags;
+
+ if (changed & SS_RESET) {
+ if (state->flags & SS_RESET) {
+ gpio_set_value(GPIO_RESET, 1); /* assert reset */
+ gpio_set_value(GPIO_OUTEN, 1); /* buffers off */
+ } else {
+ gpio_set_value(GPIO_RESET, 0); /* deassert reset */
+ gpio_set_value(GPIO_OUTEN, 0); /* buffers on */
+ msleep(500);
+ }
+ }
+
+ sock->old_flags = state->flags;
+
+ return 0;
+}
+
+static int xxs1500_pcmcia_get_status(struct pcmcia_socket *skt,
+ unsigned int *value)
+{
+ unsigned int status;
+ int i;
+
+ status = 0;
+
+ /* check carddetects: GPIO[0:1] must both be low */
+ if (!gpio_get_value(GPIO_CDA) && !gpio_get_value(GPIO_CDB))
+ status |= SS_DETECT;
+
+ /* determine card voltage: GPIO[208:209] binary value */
+ i = (!!gpio_get_value(GPIO_VSL)) | ((!!gpio_get_value(GPIO_VSH)) << 1);
+
+ switch (i) {
+ case 0:
+ case 1:
+ case 2:
+ status |= SS_3VCARD; /* 3V card */
+ break;
+ case 3: /* 5V card, unsupported */
+ default:
+ status |= SS_XVCARD; /* treated as unsupported in core */
+ }
+
+ /* GPIO214: low active power switch */
+ status |= gpio_get_value(GPIO_POWER) ? 0 : SS_POWERON;
+
+ /* GPIO204: high-active reset line */
+ status |= gpio_get_value(GPIO_RESET) ? SS_RESET : SS_READY;
+
+ /* other stuff */
+ status |= gpio_get_value(GPIO_BATTDEAD) ? 0 : SS_BATDEAD;
+ status |= gpio_get_value(GPIO_BATTWARN) ? 0 : SS_BATWARN;
+
+ *value = status;
+
+ return 0;
+}
+
+static int xxs1500_pcmcia_sock_init(struct pcmcia_socket *skt)
+{
+ gpio_direction_input(GPIO_CDA);
+ gpio_direction_input(GPIO_CDB);
+ gpio_direction_input(GPIO_VSL);
+ gpio_direction_input(GPIO_VSH);
+ gpio_direction_input(GPIO_BATTDEAD);
+ gpio_direction_input(GPIO_BATTWARN);
+ gpio_direction_output(GPIO_RESET, 1); /* assert reset */
+ gpio_direction_output(GPIO_OUTEN, 1); /* disable buffers */
+ gpio_direction_output(GPIO_POWER, 1); /* power off */
+
+ return 0;
+}
+
+static int xxs1500_pcmcia_sock_suspend(struct pcmcia_socket *skt)
+{
+ return 0;
+}
+
+static int au1x00_pcmcia_set_io_map(struct pcmcia_socket *skt,
+ struct pccard_io_map *map)
+{
+ struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
+
+ map->start = (u32)sock->virt_io;
+ map->stop = map->start + IO_MAP_SIZE;
+
+ return 0;
+}
+
+static int au1x00_pcmcia_set_mem_map(struct pcmcia_socket *skt,
+ struct pccard_mem_map *map)
+{
+ struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
+
+ if (map->flags & MAP_ATTRIB)
+ map->static_start = sock->phys_attr + map->card_start;
+ else
+ map->static_start = sock->phys_mem + map->card_start;
+
+ return 0;
+}
+
+static struct pccard_operations xxs1500_pcmcia_operations = {
+ .init = xxs1500_pcmcia_sock_init,
+ .suspend = xxs1500_pcmcia_sock_suspend,
+ .get_status = xxs1500_pcmcia_get_status,
+ .set_socket = xxs1500_pcmcia_configure,
+ .set_io_map = au1x00_pcmcia_set_io_map,
+ .set_mem_map = au1x00_pcmcia_set_mem_map,
+};
+
+static int __devinit xxs1500_pcmcia_probe(struct platform_device *pdev)
+{
+ struct xxs1500_pcmcia_sock *sock;
+ struct resource *r;
+ phys_t physio;
+ int ret, irq;
+
+ sock = kzalloc(sizeof(struct xxs1500_pcmcia_sock), GFP_KERNEL);
+ if (!sock)
+ return -ENOMEM;
+
+ ret = -ENODEV;
+
+ /*
+ * pseudo-attr: The 32bit address of the PCMCIA attribute space
+ * for this socket (usually the 36bit address shifted 4 to the
+ * right).
+ */
+ r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pseudo-attr");
+ if (!r) {
+ dev_err(&pdev->dev, "missing 'pseudo-attr' resource!\n");
+ goto out0;
+ }
+ sock->phys_attr = r->start;
+
+ /*
+ * pseudo-mem: The 32bit address of the PCMCIA memory space for
+ * this socket (usually the 36bit address shifted 4 to the right)
+ */
+ r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pseudo-mem");
+ if (!r) {
+ dev_err(&pdev->dev, "missing 'pseudo-mem' resource!\n");
+ goto out0;
+ }
+ sock->phys_mem = r->start;
+
+ /*
+ * pseudo-io: The 32bit address of the PCMCIA IO space for this
+ * socket (usually the 36bit address shifted 4 to the right).
+ */
+ r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pseudo-io");
+ if (!r) {
+ dev_err(&pdev->dev, "missing 'pseudo-io' resource!\n");
+ goto out0;
+ }
+ sock->phys_io = r->start;
+
+
+ /* for io must remap the full 36bit address (for reference see
+ * alchemy/common/setup.c::__fixup_bigphys_addr)
+ */
+ physio = ((phys_t)sock->phys_io) << 4;
+
+ /*
+ * PCMCIA client drivers use the inb/outb macros to access
+ * the IO registers. Since mips_io_port_base is added
+ * to the access address of the mips implementation of
+ * inb/outb, we need to subtract it here because we want
+ * to access the I/O or MEM address directly, without
+ * going through this "mips_io_port_base" mechanism.
+ */
+ sock->virt_io = (void *)(ioremap(physio, IO_MAP_SIZE) -
+ mips_io_port_base);
+
+ if (!sock->virt_io) {
+ dev_err(&pdev->dev, "cannot remap IO area\n");
+ ret = -ENOMEM;
+ goto out0;
+ }
+
+ sock->socket.ops = &xxs1500_pcmcia_operations;
+ sock->socket.owner = THIS_MODULE;
+ sock->socket.pci_irq = gpio_to_irq(GPIO_CARDIRQ);
+ sock->socket.features = SS_CAP_STATIC_MAP | SS_CAP_PCCARD;
+ sock->socket.map_size = MEM_MAP_SIZE;
+ sock->socket.io_offset = (unsigned long)sock->virt_io;
+ sock->socket.dev.parent = &pdev->dev;
+ sock->socket.resource_ops = &pccard_static_ops;
+
+ platform_set_drvdata(pdev, sock);
+
+ /* setup carddetect irq: use one of the 2 GPIOs as an
+ * edge detector.
+ */
+ irq = gpio_to_irq(GPIO_CDA);
+ set_irq_type(irq, IRQ_TYPE_EDGE_BOTH);
+ ret = request_irq(irq, cdirq, 0, "pcmcia_carddetect", sock);
+ if (ret) {
+ dev_err(&pdev->dev, "cannot setup cd irq\n");
+ goto out1;
+ }
+
+ ret = pcmcia_register_socket(&sock->socket);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to register\n");
+ goto out2;
+ }
+
+ printk(KERN_INFO "MyCable XXS1500 PCMCIA socket services\n");
+
+ return 0;
+
+out2:
+ free_irq(gpio_to_irq(GPIO_CDA), sock);
+out1:
+ iounmap((void *)(sock->virt_io + (u32)mips_io_port_base));
+out0:
+ kfree(sock);
+ return ret;
+}
+
+static int __devexit xxs1500_pcmcia_remove(struct platform_device *pdev)
+{
+ struct xxs1500_pcmcia_sock *sock = platform_get_drvdata(pdev);
+
+ pcmcia_unregister_socket(&sock->socket);
+ free_irq(gpio_to_irq(GPIO_CDA), sock);
+ iounmap((void *)(sock->virt_io + (u32)mips_io_port_base));
+ kfree(sock);
+
+ return 0;
+}
+
+static struct platform_driver xxs1500_pcmcia_socket_driver = {
+ .driver = {
+ .name = "xxs1500_pcmcia",
+ .owner = THIS_MODULE,
+ },
+ .probe = xxs1500_pcmcia_probe,
+ .remove = __devexit_p(xxs1500_pcmcia_remove),
+};
+
+int __init xxs1500_pcmcia_socket_load(void)
+{
+ return platform_driver_register(&xxs1500_pcmcia_socket_driver);
+}
+
+void __exit xxs1500_pcmcia_socket_unload(void)
+{
+ platform_driver_unregister(&xxs1500_pcmcia_socket_driver);
+}
+
+module_init(xxs1500_pcmcia_socket_load);
+module_exit(xxs1500_pcmcia_socket_unload);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("PCMCIA Socket Services for MyCable XXS1500 systems");
+MODULE_AUTHOR("Manuel Lauss");
--
1.6.5.rc2
More information about the linux-pcmcia
mailing list