cs: pcmcia_socket0: unable to apply power
debian.potato at libero.it
debian.potato at libero.it
Sat Aug 2 09:28:38 EDT 2008
Hi folks,
I have a problem with my wireless PCMCIA card. I have a slack 12.1 freshly installed, kernel 2.6.24.5 and a wifi pcmcia card "Digicom" (is an Italian device using the intersil isl3890 chip). The card is recognized by lspci as follows:
Intersil Corporation ISL3890 [Prism GT/Prism Duette]/ISL3886 [Prism Javelin/Prism Xbow]
But pccardctl didn’t recognize it:
root at giorgix:~# pccardctl info
PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
FUNCID=255
root at giorgix:~# pccardctl ident
Socket 0:
no product info available
The card works greatly with the same laptop, slack 11 with kernel 2.4.x, using module prism54. Some days ago I installed slack 12.1 and the card doesn't work anymore.
At first I supposed it was a module problem: so after a google search I discovered that prism54 released two different modules: one for the "fullmac" card (called prism54), and one for the "softmac" card (called islsm or p54)
I tried to use both drivers independently (using the blacklist to avoid one of them was loaded) because a user in a forum reported to me that he has the same card and (with a debian) it works better with the softmac module.
Here is what I obtained using the prism54 module and blacklisting p54 driver:
-The system load only prism54 module
-The led turns on, blinks and after few seconds turns off;
-/var/log/messages reports:
Jul 26 12:03:24 giorgix kernel: ACPI: PCI interrupt for device 0000:02:00.0 disabled
Jul 26 12:03:27 giorgix kernel: pccard: CardBus card inserted into slot 0
Jul 26 12:03:27 giorgix kernel: ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
-/var/log/syslog reports:
Jul 26 12:03:27 giorgix kernel: PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Jul 26 12:03:29 giorgix kernel: eth1: timeout waiting for mgmt response
Jul 26 12:03:29 giorgix kernel: eth1: mgt_commit_list: failure. oid=ff020003 err=-110
Jul 26 12:03:30 giorgix kernel: eth1: timeout waiting for mgmt response
Jul 26 12:03:30 giorgix kernel: eth1: mgt_commit_list: failure. oid=10000002 err=-110
Jul 26 12:03:31 giorgix kernel: eth1: timeout waiting for mgmt response
Jul 26 12:03:31 giorgix kernel: eth1: mgt_commit_list: failure. oid=12000002 err=-110
Jul 26 12:03:32 giorgix kernel: eth1: timeout waiting for mgmt response
Jul 26 12:03:32 giorgix kernel: eth1: mgt_commit_list: failure. oid=12000007 err=-110
Jul 26 12:03:33 giorgix kernel: eth1: timeout waiting for mgmt response
Jul 26 12:03:33 giorgix kernel: eth1: mgt_commit_list: failure. oid=ff020003 err=-110
Jul 26 12:03:33 giorgix kernel: eth1: interface reset failure
Jul 26 12:03:33 giorgix kernel: prism54: Your card/socket may be faulty, or IRQ line too
busy :(
-/var/log/debug reports:
Jul 26 12:03:24 giorgix kernel: eth1: hot unplug detected
Jul 26 12:03:24 giorgix kernel: eth1: removing device
Jul 26 12:03:28 giorgix kernel: eth1: resetting device...
Jul 26 12:03:28 giorgix kernel: eth1: uploading firmware...
Jul 26 12:03:28 giorgix kernel: eth1: firmware version: 1.0.4.3
Jul 26 12:03:28 giorgix kernel: eth1: firmware upload complete
Jul 26 12:03:28 giorgix kernel: eth1: expecting oid 0xff020003, received 0x2009806.
Jul 26 12:03:28 giorgix kernel: eth1: timeout waiting for mgmt response 249, triggering device
Jul 26 12:03:28 giorgix kernel: eth1: timeout waiting for mgmt response 224, triggering d device
Jul 26 12:03:28 giorgix kernel: eth1: timeout waiting for mgmt response 199, triggering device (repeated many times)
Here is what I obtained using the p54 module and blacklisting prism54 driver:
-The system loads the following modules: p54pci, p54common. mac80211, cfg80211
-The led does not turn on
-/var/log/mssages reports:
Jul 26 12:11:21 giorgix kernel: pccard: CardBus card inserted into slot 0
Jul 26 12:11:22 giorgix kernel: ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
Jul 26 12:11:22 giorgix kernel: p54: LM86 firmware
Jul 26 12:11:22 giorgix kernel: p54: FW rev 2.7.0.0 - Softmac protocol 4.1
Jul 26 12:11:23 giorgix kernel: phy0: hwaddr 00:02:6f:20:ba:8b, isl3890
-/var/log/syslog reports:
Jul 26 12:11:21 giorgix kernel: cs: pcmcia_socket0: unable to apply power.
Jul 26 12:11:22 giorgix kernel: PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
-In /var/log/debug reports:
Jul 26 12:11:22 giorgix kernel: PCI: Setting latency timer of device 0000:02:00.0 to 64
Jul 26 12:11:23 giorgix kernel: phy0: Selected rate control algorithm 'simple'
I posted this information on the net, and a user pointed out my attention to the following lines:
Jul 26 12:11:21 giorgix kernel: cs: pcmcia_socket0: unable to apply power.
And
Jul 26 12:03:33 giorgix kernel: prism54: Your card/socket may be faulty, or IRQ line too busy :(
The problem concerns the PCMCIA socket and not the module. So I tried to post here hoping in some hint. Actually, the problem is similar to the one reported here http://www.kernel.org/pub/linux/utils/kernel/pcmcia/powerbugs.html.
Some additional info:
My laptop is an Acer Aspire 1350 series (specs: http://www.ciao.co.uk/Acer_Aspire_1355LM__6524138#productdetail)
The CardBus Bridge is a texas instruments pci1410.
Lspci –vv reports:
00:00.0 Host bridge: VIA Technologies, Inc. VT8378 [KM400/A] Chipset Host Bridge
Subsystem: VIA Technologies, Inc. Unknown device 7205
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [80] AGP version 3.5
Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: agpgart-via
Kernel modules: via-agp
00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d0100000-d01fffff
Prefetchable memory behind bridge: d8000000-dfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: shpchp
00:07.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02)
Subsystem: Acer Incorporated [ALI] Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 38000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 30000000-33fff000 (prefetchable)
Memory window 1: 34000000-37fff000
I/O window 0: 00002000-000020ff
I/O window 1: 00002400-000024ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
00:08.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 0033
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d0004000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ohci1394
Kernel modules: ohci1394
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 4
Region 4: I/O ports at 1c00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 1c20 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 9
Region 4: I/O ports at 1c40 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 11
Region 0: Memory at d0004800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: Acer Incorporated [ALI] Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: i2c-viapro, via-ircc
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Acer Incorporated [ALI] Unknown device 0033
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 4
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at 1c60 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: VIA_IDE
Kernel modules: pata_via
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
Subsystem: Acer Incorporated [ALI] Unknown device 0033
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 9
Region 0: I/O ports at 1000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: VIA 82xx Audio
Kernel modules: snd-via82xx
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80)
Subsystem: Acer Incorporated [ALI] Unknown device 0033
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 9
Region 0: I/O ports at 1400 [size=256]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: snd-via82xx-modem
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
Subsystem: Acer Incorporated [ALI] Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 4
Region 0: I/O ports at 1800 [size=256]
Region 1: Memory at d0004c00 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
Kernel modules: via-rhine
01:00.0 VGA compatible controller: ATI Technologies Inc M9+ 5C61 [Radeon Mobility 9200 (AGP)] (rev 01) (prog-if 00 [VGA controller])
Subsystem: Acer Incorporated [ALI] Unknown device 0033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B+ DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 4
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at d0120000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: radeonfb
02:00.0 Network controller: Intersil Corporation ISL3890 [Prism GT/Prism Duette]/ISL3886 [Prism Javelin/Prism Xbow] (rev 01)
Subsystem: Intersil Corporation WG511 Wireless Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 80 (2500ns min, 7000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 34000000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: prism54
Kernel modules: prism54, p54pci
Any help will be appreciated.
Giorgio
More information about the linux-pcmcia
mailing list