TI PCI1225 controller + any CardBus card == "no high memory space"
Adonis
4donis at gmail.com
Sun Nov 11 03:08:51 EST 2007
Hi everyone,
I have a PCI card which carries the Texas Instruments 1225 controller
chip on it, and no matter which CardBus card I try on it (WiFi,
USB2.0), I get the ugly "no high memory space" warning and the card is
rendered useless in the system. On the other hand a PC-Card (16bit)
WiFi works just dandy!
Here is the systems' information:
CPU/MOTHERBOARD:
--------------------------------------------------------------------------------------------
AMD Duron 1333Mhz
Biostar AMD-760 M7MIA version 2.0 (latest BIOS)
MIA1101F -- 11/01/2001-761-686B
http://www.biostar-usa.com/mbdetails.asp?model=M7MIA
Only used slots are the PCI PCMCIA card and the video card
BIOS settings:
USB ports: enabled
USB kbd support: enabled
audio/modem codec + SB support: enabled
IDE: enabled
IDE-RAID: disabled
parallel port (EPP): enabled
serial ports: enabled
BIOS shadowing: disabled
PNP: disabled
ACPI: enabled and forced on or off via kernel command line makes no difference
DISTRO:
--------------------------------------------------------------------------------------------
Knoppix 5.0.1 2006-06-01
UNAME:
--------------------------------------------------------------------------------------------
Linux Knoppix 2.6.17 #4 SMP PREEMPT Wed May 10 13:53:45 CEST 2006 i686 GNU/Linux
/ETC/PCMCIA/CONFIG.OPTS
--------------------------------------------------------------------------------------------
#
# Local PCMCIA Configuration File
#
#----------------------------------------------------------------------
# System resources available for PCMCIA devices
# Dell Notebooks freeze if something between 0x810-0x81f is included!
include port 0x100-0x4ff, port 0x800-0x80f, port 0x820-0x8ff, port 0xc00-0xcff
include memory 0xc0000-0xfffff
include memory 0xa0000000-0xa0ffffff, memory 0x60000000-0x60ffffff
# High port numbers do not always work...
# include port 0x1000-0x17ff
# Extra port range for IBM Token Ring
include port 0xa00-0xaff
# Resources we should not use, even if they appear to be available
# First built-in serial port
exclude irq 4
# Second built-in serial port
#exclude irq 3
# First built-in parallel port (if used by parport_pc)
#exclude irq 7
# PS/2 mouse
exclude irq 12
DMESG (both PCI card and CardBus card inserted before boot):
--------------------------------------------------------------------------------------------
Linux version 2.6.17 (root at Knoppix) (gcc version 4.0.4 20060507
(prerelease) (Debian 4.0.3-3)) #4 SMP PREEMPT Wed May 10 13:53:45 CEST
2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 61424 pages, LIFO batch:15
DMI 2.2 present.
ACPI: RSDP (v000 BIOSTA ) @ 0x000f5f40
ACPI: RSDT (v001 BIOSTA AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3000
ACPI: FADT (v001 BIOSTA AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3040
ACPI: DSDT (v001 BIOSTA AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: BIOS age (2001) fails cutoff (2002), acpi=force is required to enable ACPI
ACPI: Disabling ACPI support
Allocating PCI resources starting at 20000000 (gap: 10000000:efff0000)
Built 1 zonelists
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us
apm=power-off vga=791 initrd=minirt.gz nomce quiet BOOT_IMAGE=knoppix
BOOT_IMAGE=linux dma 2
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0120a000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Detected 1333.560 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 254740k/262080k available (2225k kernel code, 6720k reserved,
807k data, 324k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2671.64 BogoMIPS (lpj=5343296)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff c1cbf9ff 00000000 00000000
00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000420
00000000 00000000 00000000
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
CPU0: AMD Duron(tm) processor stepping 01
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 729k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfb4f0, last bus=1
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbed0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbf00, dseg 0xf0000
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 6000-607f claimed by vt82c686 HW-mon
PCI quirk: region 5000-500f claimed by vt82c686 SMB
Boot video device is 0000:01:05.0
PCI: Using IRQ router VIA [1106/0686] at 0000:00:07.0
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e0000000-e1ffffff
PREFETCH window: d8000000-dfffffff
PCI: Bus 2, cardbus bridge: 0000:00:09.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bus 6, cardbus bridge: 0000:00:09.1
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 24000000-25ffffff
MEM window: 26000000-27ffffff
PCI: Found IRQ 11 for device 0000:00:09.0
PCI: Sharing IRQ 11 with 0000:00:09.1
PCI: Sharing IRQ 11 with 0000:01:05.0
PCI: Found IRQ 11 for device 0000:00:09.1
PCI: Sharing IRQ 11 with 0000:00:09.0
PCI: Sharing IRQ 11 with 0000:01:05.0
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 98304 bytes)
TCP bind hash table entries: 4096 (order: 3, 49152 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1194729079.448:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
PCI: Disabling Via external APIC routing
vesafb: framebuffer at 0xd8000000, mapped to 0xd0880000, using 3072k,
total 32768k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:0eb9
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0xc400-0xc407, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xc408-0xc40f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: QUANTUM FIREBALLlct10 10, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HITACHI DVD-ROM GD-7000, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 20044080 sectors (10262 MB) w/418KiB Cache, CHS=19885/16/63
hda: cache flushes not supported
hda: hda1
hdc: ATAPI 40X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
EISA: Detected 0 cards.
NET: Registered protocol family 1
NET: Registered protocol family 15
Using IPI No-Shortcut mode
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
input: AT Translated Set 2 keyboard as /class/input/input0
VFS: Mounted root (ext2 filesystem).
Failed initialization of WD-7000 SCSI card!
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
PCI: Found IRQ 11 for device 0000:00:07.2
PCI: Sharing IRQ 11 with 0000:00:07.3
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x0000c800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Found IRQ 11 for device 0000:00:07.3
PCI: Sharing IRQ 11 with 0000:00:07.2
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.3: irq 11, io base 0x0000cc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Initializing USB Mass Storage driver...
usb 1-1: new low speed USB device using uhci_hcd and address 2
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon!
Unable to identify CD-ROM format.
VFS: Can't find an ext2 filesystem on dev hda.
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev hda.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.04
cloop: loaded (max 8 devices)
cloop: /cdrom/KNOPPIX/KNOPPIX: 31120 blocks, 65536 bytes/block,
largest block is 65552 bytes.
ISO 9660 Extensions: RRIP_1991A
Registering unionfs 20060221-0341
Freeing unused kernel memory: 324k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
PCI: Found IRQ 11 for device 0000:00:09.0
PCI: Sharing IRQ 11 with 0000:00:09.1
PCI: Sharing IRQ 11 with 0000:01:05.0
Yenta: CardBus bridge found at 0000:00:09.0 [133f:2023]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:09.0, mfunc 0x0cc07d92, devctl 0x60
Yenta: ISA IRQ mask 0x0000, PCI irq 11
Socket status: 30000020
PCI: Found IRQ 11 for device 0000:00:09.1
PCI: Sharing IRQ 11 with 0000:00:09.0
PCI: Sharing IRQ 11 with 0000:01:05.0
Yenta: CardBus bridge found at 0000:00:09.1 [133f:2023]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:09.1, mfunc 0x0cc07d92, devctl 0x60
Yenta: ISA IRQ mask 0x0000, PCI irq 11
Socket status: 30000010
pccard: CardBus card inserted into slot 0
cs: pcmcia_socket1: time out after reset.
pcmcia: Detected deprecated PCMCIA ioctl usage.
pcmcia: This interface will soon be removed from the kernel; please
expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html
for details.
cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x200-0x207 0x220-0x22f
0x2f8-0x2ff 0x330-0x337 0x378-0x37f 0x388-0x38f 0x3f8-0x3ff
0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x200-0x207 0x220-0x22f
0x2f8-0x2ff 0x330-0x337 0x378-0x37f 0x388-0x38f 0x3f8-0x3ff
0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
usbcore: registered new driver hiddev
input: Belkin Components USB-PS2 Adapter as /class/input/input2
input: USB HID v1.00 Keyboard [Belkin Components USB-PS2 Adapter ] on
usb-0000:00:07.2-1
input: Belkin Components USB-PS2 Adapter as /class/input/input3
input: USB HID v1.00 Mouse [Belkin Components USB-PS2 Adapter ] on
usb-0000:00:07.2-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
EDAC MC: Ver: 2.0.0 May 10 2006
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
shpchp: HPC vendor_id 1022 device_id 700f ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ts: Compaq touchscreen protocol output
EDAC MC0: Giving out device to "amd76x_edac" AMD761: PCI 0000:00:00.0
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0e: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
PCI: Found IRQ 10 for device 0000:00:07.5
PCI: Setting latency timer of device 0000:00:07.5 to 64
fuse init (API version 7.6)
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel at redhat.com
cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff
cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
cs: warning: no high memory space available!
cs: warning: no high memory space available!
cs: warning: no high memory space available!
cs: warning: no high memory space available!
cs: warning: no high memory space available!
cs: warning: no high memory space available!
LSPCI
--------------------------------------------------------------------------------------------
0000:00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760
[IGD4-1P] System Controller (rev 13)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e3008000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at c000 [disabled] [size=4]
Capabilities: [a0] AGP version 2.0
Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
0000:00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760
[IGD4-1P] AGP Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e0000000-e1ffffff
Prefetchable memory behind bridge: d8000000-dfffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc.
VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at c400 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at cc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.5 Multimedia audio controller: VIA Technologies, Inc.
VT82C686 AC97 Audio Controller (rev 50)
Subsystem: Sigmatel Inc Onboard Audio
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at d000 [size=256]
Region 1: I/O ports at d400 [size=4]
Region 2: I/O ports at d800 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:09.0 CardBus bridge: Texas Instruments PCI1225 (rev 01)
Subsystem: SCM Microsystems: Unknown device 2023
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x20 (128 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e3000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 20000000-21fff000 (prefetchable)
Memory window 1: 22000000-23fff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
0000:00:09.1 CardBus bridge: Texas Instruments PCI1225 (rev 01)
Subsystem: SCM Microsystems: Unknown device 2023
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x20 (128 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e3004000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 24000000-25fff000 (prefetchable)
Memory window 1: 26000000-27fff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:01:05.0 VGA compatible controller: nVidia Corporation NV11
[GeForce2 MX/MX 400] (rev a1) (prog-if 00 [VGA])
Subsystem: Palit Microsystems Inc.: Unknown device 0110
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at e1000000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
LSPCMCIA
--------------------------------------------------------------------------------------------
Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:00:09.0)
Configuration: state: on ready: yes
Voltage: 3.3V Vcc: 3.3V Vpp: 3.3V
Available IRQs: none
Available iomem: 0x00000100 - 0x000001ff
0x00000208 - 0x0000021f
0x00000230 - 0x000002f7
0x00000300 - 0x0000032f
0x00000338 - 0x00000377
0x00000380 - 0x00000387
0x00000390 - 0x000003af
0x000003bb - 0x000003d2
0x000003d4 - 0x000003f7
0x00000400 - 0x000004cf
0x000004d8 - 0x000004ff
0x00000800 - 0x0000080f
0x00000820 - 0x000008ff
0x00000a00 - 0x00000aff
0x00000c00 - 0x00000cf7
Available ioports: 0x000c0000 - 0x000fffff
CardBus card -- see "lspci" for more information
Socket 1 Bridge: [yenta_cardbus] (bus ID: 0000:00:09.1)
Configuration: state: on ready: yes
Available IRQs: none
Available iomem: 0x00000100 - 0x000001ff
0x00000208 - 0x0000021f
0x00000230 - 0x000002f7
0x00000300 - 0x0000032f
0x00000338 - 0x00000377
0x00000380 - 0x00000387
0x00000390 - 0x000003af
0x000003bb - 0x000003d2
0x000003d4 - 0x000003f7
0x00000400 - 0x000004cf
0x000004d8 - 0x000004ff
0x00000800 - 0x0000080f
0x00000820 - 0x000008ff
0x00000a00 - 0x00000aff
0x00000c00 - 0x00000cf7
Available ioports: 0x000c0000 - 0x000fffff
0x60000000 - 0x60ffffff
0xa0000000 - 0xa0ffffff
CARDCTL*
--------------------------------------------------------------------------------------------
STATUS:
Socket 0:
3.3V CardBus card
function 0: [ready]
Socket 1:
no card
CONFIG:
Socket 0:
Vcc 3.3V Vpp1 3.3V Vpp2 3.3V
interface type is "cardbus"
irq 11 [exclusive] [level]
function 0:
Socket 1:
not configured
IDENT:
Socket 0:
cs: warning: no high memory space available!
no product info available
cs: warning: no high memory space available!
cs: warning: no high memory space available!
Socket 1:
no product info available
INFO:
cs: warning: no high memory space available!
PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
cs: warning: no high memory space available!
MANFID=0000,0000
cs: warning: no high memory space available!
FUNCID=255
PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
FUNCID=255
/PROC/IO*
--------------------------------------------------------------------------------------------
00000000-0009fbff : System RAM
00000000-00000000 : Crash kernel
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cb7ff : Video ROM
000f0000-000fffff : System ROM
00100000-0ffeffff : System RAM
00100000-0032c7b8 : Kernel code
0032c7b9-003f6737 : Kernel data
0fff0000-0fff2fff : ACPI Non-volatile Storage
0fff3000-0fffffff : ACPI Tables
20000000-21ffffff : PCI CardBus #02
22000000-23ffffff : PCI CardBus #02
24000000-25ffffff : PCI CardBus #06
26000000-27ffffff : PCI CardBus #06
d0000000-d7ffffff : 0000:00:00.0
d8000000-dfffffff : PCI Bus #01
d8000000-dfffffff : 0000:01:05.0
d8000000-d9ffffff : vesafb
e0000000-e1ffffff : PCI Bus #01
e0000000-e0ffffff : 0000:01:05.0
e1000000-e100ffff : 0000:01:05.0
e3000000-e3000fff : 0000:00:09.0
e3000000-e3000fff : yenta_socket
e3004000-e3004fff : 0000:00:09.1
e3004000-e3004fff : yenta_socket
e3008000-e3008fff : 0000:00:00.0
ffff0000-ffffffff : reserved
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial
0320-0323 : b_hpsb_iso_recv_flush
0350-0353 : b_hpsb_iso_recv_flush
0376-0376 : ide1
0378-037a : parport0
037b-037f : parport0
03c0-03df : vesafb
03f6-03f6 : ide0
03f8-03ff : serial
1000-10ff : PCI CardBus #02
1400-14ff : PCI CardBus #02
1800-18ff : PCI CardBus #06
1c00-1cff : PCI CardBus #06
5000-500f : 0000:00:07.4
5000-5007 : vt596_smbus
6000-607f : 0000:00:07.4
6000-607f : via686a
c000-c003 : 0000:00:00.0
c400-c40f : 0000:00:07.1
c400-c407 : ide0
c408-c40f : ide1
c800-c81f : 0000:00:07.2
c800-c81f : uhci_hcd
cc00-cc1f : 0000:00:07.3
cc00-cc1f : uhci_hcd
d000-d0ff : 0000:00:07.5
d000-d0ff : VIA686A
d400-d403 : 0000:00:07.5
d400-d403 : VIA686A
d800-d803 : 0000:00:07.5
d800-d803 : VIA686A
/PROC/INTERRUPTS
--------------------------------------------------------------------------------------------
CPU0
0: 330780 XT-PIC timer
1: 8 XT-PIC i8042
2: 0 XT-PIC cascade
7: 0 XT-PIC parport0
8: 0 XT-PIC rtc
10: 0 XT-PIC VIA686A
11: 2585 XT-PIC uhci_hcd:usb1, uhci_hcd:usb2, yenta, yenta
12: 449 XT-PIC i8042
14: 193 XT-PIC ide0
15: 4336 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
DMESG WITH WORKING CARD
--------------------------------------------------------------------------------------------
Linux version 2.6.17 (root at Knoppix) (gcc version 4.0.4 20060507
(prerelease) (Debian 4.0.3-3)) #4 SMP PREEMPT Wed May 10 13:53:45 CEST
2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 61424 pages, LIFO batch:15
DMI 2.2 present.
ACPI: RSDP (v000 BIOSTA ) @ 0x000f5f40
ACPI: RSDT (v001 BIOSTA AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3000
ACPI: FADT (v001 BIOSTA AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3040
ACPI: DSDT (v001 BIOSTA AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: BIOS age (2001) fails cutoff (2002), acpi=force is required to enable ACPI
ACPI: Disabling ACPI support
Allocating PCI resources starting at 20000000 (gap: 10000000:efff0000)
Built 1 zonelists
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us
apm=power-off vga=791 initrd=minirt.gz nomce quiet BOOT_IMAGE=knoppix
BOOT_IMAGE=linux dma 2
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0120a000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Detected 1010.088 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 254740k/262080k available (2225k kernel code, 6720k reserved,
807k data, 324k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2023.64 BogoMIPS (lpj=4047283)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff c1cbf9ff 00000000 00000000
00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000420
00000000 00000000 00000000
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
CPU0: AMD Duron(tm) processor stepping 01
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 729k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfb4f0, last bus=1
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbed0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbf00, dseg 0xf0000
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 6000-607f claimed by vt82c686 HW-mon
PCI quirk: region 5000-500f claimed by vt82c686 SMB
Boot video device is 0000:01:05.0
PCI: Using IRQ router VIA [1106/0686] at 0000:00:07.0
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e0000000-e1ffffff
PREFETCH window: d8000000-dfffffff
PCI: Bus 2, cardbus bridge: 0000:00:09.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bus 6, cardbus bridge: 0000:00:09.1
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 24000000-25ffffff
MEM window: 26000000-27ffffff
PCI: Found IRQ 11 for device 0000:00:09.0
PCI: Sharing IRQ 11 with 0000:00:09.1
PCI: Sharing IRQ 11 with 0000:01:05.0
PCI: Found IRQ 11 for device 0000:00:09.1
PCI: Sharing IRQ 11 with 0000:00:09.0
PCI: Sharing IRQ 11 with 0000:01:05.0
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 98304 bytes)
TCP bind hash table entries: 4096 (order: 3, 49152 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1194732288.472:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
PCI: Disabling Via external APIC routing
vesafb: framebuffer at 0xd8000000, mapped to 0xd0880000, using 3072k,
total 32768k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:0eb9
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0xc400-0xc407, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xc408-0xc40f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: QUANTUM FIREBALLlct10 10, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HITACHI DVD-ROM GD-7000, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 20044080 sectors (10262 MB) w/418KiB Cache, CHS=19885/16/63
hda: cache flushes not supported
hda: hda1
hdc: ATAPI 40X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
EISA: Detected 0 cards.
NET: Registered protocol family 1
NET: Registered protocol family 15
Using IPI No-Shortcut mode
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
input: AT Translated Set 2 keyboard as /class/input/input0
VFS: Mounted root (ext2 filesystem).
Failed initialization of WD-7000 SCSI card!
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
PCI: Found IRQ 11 for device 0000:00:07.2
PCI: Sharing IRQ 11 with 0000:00:07.3
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x0000c800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Found IRQ 11 for device 0000:00:07.3
PCI: Sharing IRQ 11 with 0000:00:07.2
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.3: irq 11, io base 0x0000cc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Initializing USB Mass Storage driver...
usb 1-1: new low speed USB device using uhci_hcd and address 2
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon!
Unable to identify CD-ROM format.
VFS: Can't find an ext2 filesystem on dev hda.
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev hda.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.04
cloop: loaded (max 8 devices)
cloop: /cdrom/KNOPPIX/KNOPPIX: 31120 blocks, 65536 bytes/block,
largest block is 65552 bytes.
ISO 9660 Extensions: RRIP_1991A
Registering unionfs 20060221-0341
Freeing unused kernel memory: 324k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
PCI: Found IRQ 11 for device 0000:00:09.0
PCI: Sharing IRQ 11 with 0000:00:09.1
PCI: Sharing IRQ 11 with 0000:01:05.0
Yenta: CardBus bridge found at 0000:00:09.0 [133f:2023]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:09.0, mfunc 0x0cc07d92, devctl 0x60
Yenta: ISA IRQ mask 0x0000, PCI irq 11
Socket status: 30000010
PCI: Found IRQ 11 for device 0000:00:09.1
PCI: Sharing IRQ 11 with 0000:00:09.0
PCI: Sharing IRQ 11 with 0000:01:05.0
Yenta: CardBus bridge found at 0000:00:09.1 [133f:2023]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:09.1, mfunc 0x0cc07d92, devctl 0x60
Yenta: ISA IRQ mask 0x0000, PCI irq 11
Socket status: 30000010
pccard: PCMCIA card inserted into slot 0
cs: pcmcia_socket1: time out after reset.
pcmcia: Detected deprecated PCMCIA ioctl usage.
pcmcia: This interface will soon be removed from the kernel; please
expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html
for details.
cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x200-0x207 0x220-0x22f
0x2f8-0x2ff 0x330-0x337 0x378-0x37f 0x388-0x38f 0x3f8-0x3ff
0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x200-0x207 0x220-0x22f
0x2f8-0x2ff 0x330-0x337 0x378-0x37f 0x388-0x38f 0x3f8-0x3ff
0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco 0.15rc3 (David Gibson <hermes at gibson.dropbear.id.au>, Pavel
Roskin <proski at gnu.org>, et al)
orinoco_cs 0.15rc3 (David Gibson <hermes at gibson.dropbear.id.au>, Pavel
Roskin <proski at gnu.org>, et al)
pcmcia: registering new device pcmcia0.0
eth0: Hardware identity 0001:0001:0004:0000
eth0: Station identity 001f:0001:0006:0010
eth0: Firmware determined as Lucent/Agere 6.16
eth0: Ad-hoc demo mode supported
eth0: IEEE standard IBSS ad-hoc mode supported
eth0: WEP supported, 104-bit key
eth0: MAC address 00:60:1D:F2:9C:A6
eth0: Station name "HERMES I"
eth0: ready
eth0: index 0x01: , irq 11, io 0x0100-0x013f
eth0: New link status: Connected (0001)
NET: Registered protocol family 17
usbcore: registered new driver hiddev
input: Belkin Components USB-PS2 Adapter as /class/input/input2
input: USB HID v1.00 Keyboard [Belkin Components USB-PS2 Adapter ] on
usb-0000:00:07.2-1
input: Belkin Components USB-PS2 Adapter as /class/input/input3
input: USB HID v1.00 Mouse [Belkin Components USB-PS2 Adapter ] on
usb-0000:00:07.2-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
EDAC MC: Ver: 2.0.0 May 10 2006
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
ts: Compaq touchscreen protocol output
parport_pc: VIA parallel port: io=0x378, irq=7
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0e: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
EDAC MC0: Giving out device to "amd76x_edac" AMD761: PCI 0000:00:00.0
Linux agpgart interface v0.101 (c) Dave Jones
shpchp: HPC vendor_id 1022 device_id 700f ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
PCI: Found IRQ 10 for device 0000:00:07.5
PCI: Setting latency timer of device 0000:00:07.5 to 64
fuse init (API version 7.6)
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel at redhat.com
eth0: New link status: Connected (0001)
eth0: New link status: AP Out of Range (0004)
LSPCI WITH WORKING CARD
--------------------------------------------------------------------------------------------
0000:00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760
[IGD4-1P] System Controller (rev 13)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e3008000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at c000 [disabled] [size=4]
Capabilities: [a0] AGP version 2.0
Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
0000:00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760
[IGD4-1P] AGP Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e0000000-e1ffffff
Prefetchable memory behind bridge: d8000000-dfffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc.
VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at c400 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at cc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.5 Multimedia audio controller: VIA Technologies, Inc.
VT82C686 AC97 Audio Controller (rev 50)
Subsystem: Sigmatel Inc Onboard Audio
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at d000 [size=256]
Region 1: I/O ports at d400 [size=4]
Region 2: I/O ports at d800 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:09.0 CardBus bridge: Texas Instruments PCI1225 (rev 01)
Subsystem: SCM Microsystems: Unknown device 2023
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x20 (128 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e3000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 20000000-21fff000 (prefetchable)
Memory window 1: 22000000-23fff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
16-bit legacy interface ports at 0001
0000:00:09.1 CardBus bridge: Texas Instruments PCI1225 (rev 01)
Subsystem: SCM Microsystems: Unknown device 2023
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x20 (128 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e3004000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 24000000-25fff000 (prefetchable)
Memory window 1: 26000000-27fff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:01:05.0 VGA compatible controller: nVidia Corporation NV11
[GeForce2 MX/MX 400] (rev a1) (prog-if 00 [VGA])
Subsystem: Palit Microsystems Inc.: Unknown device 0110
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at e1000000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
LSPCMCIA WITH WORKING CARD
--------------------------------------------------------------------------------------------
Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:00:09.0)
Configuration: state: on ready: yes
Voltage: 5.0V Vcc: 5.0V Vpp: 0.0V
Available IRQs: none
Available iomem: 0x00000100 - 0x000001ff
0x00000208 - 0x0000021f
0x00000230 - 0x000002f7
0x00000300 - 0x0000032f
0x00000338 - 0x00000377
0x00000380 - 0x00000387
0x00000390 - 0x000003af
0x000003bb - 0x000003d2
0x000003d4 - 0x000003f7
0x00000400 - 0x000004cf
0x000004d8 - 0x000004ff
0x00000800 - 0x0000080f
0x00000820 - 0x000008ff
0x00000a00 - 0x00000aff
0x00000c00 - 0x00000cf7
Available ioports: 0x000c0000 - 0x000fffff
0x60000000 - 0x60ffffff
0xa0000000 - 0xa0ffffff
Socket 0 Device 0: [orinoco_cs] (bus ID: 0.0)
Configuration: state: on
Product Name: Lucent Technologies WaveLAN/IEEE Version 01.01
Identification: manf_id: 0x0156 card_id: 0x0002
function: 6 (network)
prod_id(1): "Lucent Technologies" (0x23eb9949)
prod_id(2): "WaveLAN/IEEE" (0xc562e72a)
prod_id(3): "Version 01.01" (0xd27deb1a)
prod_id(4): --- (---)
Socket 1 Bridge: [yenta_cardbus] (bus ID: 0000:00:09.1)
Configuration: state: on ready: yes
Available IRQs: none
Available iomem: 0x00000100 - 0x000001ff
0x00000208 - 0x0000021f
0x00000230 - 0x000002f7
0x00000300 - 0x0000032f
0x00000338 - 0x00000377
0x00000380 - 0x00000387
0x00000390 - 0x000003af
0x000003bb - 0x000003d2
0x000003d4 - 0x000003f7
0x00000400 - 0x000004cf
0x000004d8 - 0x000004ff
0x00000800 - 0x0000080f
0x00000820 - 0x000008ff
0x00000a00 - 0x00000aff
0x00000c00 - 0x00000cf7
Available ioports: 0x000c0000 - 0x000fffff
0x60000000 - 0x60ffffff
0xa0000000 - 0xa0ffffff
CARDCTL* WITH WORKING CARD
--------------------------------------------------------------------------------------------
STATUS:
Socket 0:
5V 16-bit PC Card
function 0: [ready]
Socket 1:
no card
CONFIG:
Socket 0:
Vcc 0.2V Vpp1 99.2V Vpp2 109051904.0V
interface type is irq 11 [exclusive] [level]
function 0:
config base 0x0001
option 0x00
io 0x0100-0x013f [16bit]
Socket 1:
not configured
IDENT:
Socket 0:
product info: "Lucent Technologies", "WaveLAN/IEEE", "Version 01.01", ""
manfid: 0x0156, 0x0002
function: 6 (network)
Socket 1:
no product info available
INFO:
PRODID_1="Lucent Technologies"
PRODID_2="WaveLAN/IEEE"
PRODID_3="Version 01.01"
PRODID_4=""
MANFID=0156,0002
FUNCID=6
PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
FUNCID=255
/PROC/IO* WITH WORKING CARD
--------------------------------------------------------------------------------------------
00000000-0009fbff : System RAM
00000000-00000000 : Crash kernel
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cb7ff : Video ROM
000f0000-000fffff : System ROM
00100000-0ffeffff : System RAM
00100000-0032c7b8 : Kernel code
0032c7b9-003f6737 : Kernel data
0fff0000-0fff2fff : ACPI Non-volatile Storage
0fff3000-0fffffff : ACPI Tables
20000000-21ffffff : PCI CardBus #02
22000000-23ffffff : PCI CardBus #02
24000000-25ffffff : PCI CardBus #06
26000000-27ffffff : PCI CardBus #06
a0000000-a0000fff : pcmcia_socket0
d0000000-d7ffffff : 0000:00:00.0
d8000000-dfffffff : PCI Bus #01
d8000000-dfffffff : 0000:01:05.0
d8000000-d9ffffff : vesafb
e0000000-e1ffffff : PCI Bus #01
e0000000-e0ffffff : 0000:01:05.0
e1000000-e100ffff : 0000:01:05.0
e3000000-e3000fff : 0000:00:09.0
e3000000-e3000fff : yenta_socket
e3004000-e3004fff : 0000:00:09.1
e3004000-e3004fff : yenta_socket
e3008000-e3008fff : 0000:00:00.0
ffff0000-ffffffff : reserved
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0100-013f : pcmcia_socket0
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial
0320-0323 : b_hpsb_iso_recv_flush
0350-0353 : b_hpsb_iso_recv_flush
0376-0376 : ide1
0378-037a : parport0
037b-037f : parport0
03c0-03df : vesafb
03f2-03f5 : floppy
03f6-03f6 : ide0
03f7-03f7 : floppy DIR
03f8-03ff : serial
1000-10ff : PCI CardBus #02
1400-14ff : PCI CardBus #02
1800-18ff : PCI CardBus #06
1c00-1cff : PCI CardBus #06
5000-500f : 0000:00:07.4
5000-5007 : vt596_smbus
6000-607f : 0000:00:07.4
6000-607f : via686a
c000-c003 : 0000:00:00.0
c400-c40f : 0000:00:07.1
c400-c407 : ide0
c408-c40f : ide1
c800-c81f : 0000:00:07.2
c800-c81f : uhci_hcd
cc00-cc1f : 0000:00:07.3
cc00-cc1f : uhci_hcd
d000-d0ff : 0000:00:07.5
d000-d0ff : VIA686A
d400-d403 : 0000:00:07.5
d400-d403 : VIA686A
d800-d803 : 0000:00:07.5
d800-d803 : VIA686A
/PROC/INTERRUPTS WITH WORKING CARD
--------------------------------------------------------------------------------------------
CPU0
0: 66160 XT-PIC timer
1: 8 XT-PIC i8042
2: 0 XT-PIC cascade
6: 57 XT-PIC floppy
7: 0 XT-PIC parport0
8: 0 XT-PIC rtc
10: 0 XT-PIC VIA686A
11: 1972 XT-PIC uhci_hcd:usb1, uhci_hcd:usb2, yenta,
yenta, pcmcia0.0
12: 113 XT-PIC i8042
14: 193 XT-PIC ide0
15: 1170 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
I tried fiddling around with config.opts, but to no avail. I also
realize that a newer kernel might fix the problem, but I'd like to
exhaust any possibilities with this combination first.
Any suggestions?
And an off-topic question: is there a Linux supported USB (1.1 or 2.0)
PC-Card (16bit) ?? I've searched for a while but couldn't find
anything like that :(
Thank you very much for any assistance!
PS. Please CC me in your reply if you could.
More information about the linux-pcmcia
mailing list