O2 Micro OZ6812 (rev 05) with usb2.0 card

[Norbert Schmidt]

Hello,

realizing that my usb2.0/firewire-card works fine in a

02:00.0 CardBus bridge: Texas Instruments PCI1420
        Subsystem: IBM ThinkPad T23 (2647-4MG)
        Flags: bus master, medium devsel, latency 168, IRQ 11
        Memory at 50000000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
        Memory window 0: f0000000-f1fff000 (prefetchable)
        Memory window 1: c2000000-c3fff000
        I/O window 0: 00002000-000020ff
        I/O window 1: 00002400-000024ff
        16-bit legacy interface ports at 0001

02:00.1 CardBus bridge: Texas Instruments PCI1420
        Subsystem: IBM ThinkPad T23 (2647-4MG)
        Flags: bus master, medium devsel, latency 168, IRQ 11
        Memory at 51000000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=02, secondary=07, subordinate=07, sec-latency=176
        Memory window 0: f2000000-f3fff000 (prefetchable)
        Memory window 1: c4000000-c5fff000
        I/O window 0: 00002800-000028ff
        I/O window 1: 00002c00-00002cff
        16-bit legacy interface ports at 0001
 

lets me take another try to get it run in my

00:03.0 CardBus bridge: O2 Micro, Inc. OZ6812 CardBus Controller (rev 05)
        Subsystem: Uniwill Computer Corp Unknown device 3000
        Flags: bus master, stepping, slow devsel, latency 168, IRQ 10
        Memory at 28000000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
        Memory window 0: 20000000-23fff000 (prefetchable)
        Memory window 1: 24000000-27fff000
        I/O window 0: 00001000-000010ff
        I/O window 1: 00001400-000014ff
        16-bit legacy interface ports at 0001


inserting card here(usb2.0/firewire) looks good:

pccard: CardBus card inserted into slot 0
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:00.0[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:02:00.0: OHCI Host Controller
ohci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:02:00.0: irq 10, io mem 0x24000000
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.20-20070212152347-default ohci_hcd
usb usb3: SerialNumber: 0000:02:00.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Enabling device 0000:02:00.1 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:00.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:02:00.1: OHCI Host Controller
ohci_hcd 0000:02:00.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:02:00.1: irq 10, io mem 0x24001000
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.20-20070212152347-default ohci_hcd
usb usb4: SerialNumber: 0000:02:00.1
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
PCI: Enabling device 0000:02:00.3 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:00.3[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:02:00.3: EHCI Host Controller
ehci_hcd 0000:02:00.3: new USB bus registered, assigned bus number 5
ehci_hcd 0000:02:00.3: debug port 1
ehci_hcd 0000:02:00.3: irq 10, io mem 0x24002800
ehci_hcd 0000:02:00.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: new device found, idVendor=0000, idProduct=0000
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.20-20070212152347-default ehci_hcd
usb usb5: SerialNumber: 0000:02:00.3
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 6 ports detected
ieee1394: Initialized config rom entry `ip1394'
PCI: Enabling device 0000:02:00.4 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:00.4[C] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:02:00.4 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10]  MMIO=[24002000-240027ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0090e63900000201]


but inserting an high speed usb cardreader (as an example-device):

usb 5-1: new high speed USB device using ehci_hcd and address 2
usb 5-1: new device found, idVendor=0dda, idProduct=2005
usb 5-1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-1: Product: 2.0 Card Reader
usb 5-1: Manufacturer: USB Reader
usb 5-1: SerialNumber: ABCD12345678
usb 5-1: configuration #1 chosen from 1 choice
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: can't restore configuration #1 (error=-75)
usb 5-1: USB disconnect, address 2
scsi 0:0:0:0: scsi: Device offlined - not ready after error recovery
usb-storage: device scan complete


What information do you need to help here and what can I try?
(pcmcia-card and usb2.0-device work fine in the Texas Instruments PCI1420)

thanks,
Norbert