Yenta Socket work with 32-bit card but not 16-bit

[David Clark]

> What's the output of lspcmcia -vvv ?

Below are the outputs of both lspcmcia -vvv and lspci -vvv.  

One important note is that on our board we are only using slot A of the
PCI1620.  Slot B is not physically connected and is explicitly disabled
in the bootloader.  

The one thing that jump out at me from the following lspcmcia output is
the Available iomem from Socket 0 being equal to "--none--".


*********  lspcmcia -vvv  *********************
lspcmcia -vvv
Socket 0 Bridge:   	[yenta_cardbus] 	(bus ID: 0000:00:14.0)
	Configuration:	state: suspended	ready: yes
			Voltage: 5.0V Vcc: 5.0V Vpp: 5.0V
			Available IRQs: none
			Available ioports:	0xfe000000 - 0xfebfffff
			Available iomem:	--none--
Socket 1 Bridge:   	[yenta_cardbus] 	(bus ID: 0000:00:14.1)
	Configuration:	state: suspended	ready: yes
			Available IRQs: none
			Available ioports:	0xfe000000 - 0xfebfffff
			Available iomem:	0x80000000 - 0xfcffffff



*********  lspci -vvv  *********************
~ # lspci -vvv
00:00.0 Host bridge: Motorola MPC8245 [Unity] (rev 14)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-Step
ping- SERR- FastB2B-
	Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- 
<MAbort+ >SERR- <PERR-
	Latency: 64, Cache Line Size 08
	Interrupt: pin A routed to IRQ 0
	Region 0: Memory at <unassigned> (32-bit, prefetchable)
	Region 2: Memory at <unassigned> (32-bit, prefetchable)

00:10.0 I2O: Anchor Chips Inc. AN3042Q CO-MEM Lite (rev 02) (prog-if 01)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
	Latency: 128, Cache Line Size 08
	Interrupt: pin ? routed to IRQ 20
	Region 0: Memory at 00000000bfff8000 (32-bit, non-prefetchable)
[size=32
K]
	Region 1: I/O ports at bffff8 [size=8]

00:12.0 Ethernet controller: Digital Equipment Corporation DECchip
21142/43 (rev
 41)
	Subsystem: Unknown device 0400:0001
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
	Latency: 128 (5000ns min, 10000ns max), Cache Line Size 08
	Interrupt: pin A routed to IRQ 16
	Region 0: I/O ports at bfff00 [size=128]
	Region 1: Memory at 00000000bfff7c00 (32-bit, non-prefetchable)
[size=1K
]
	Expansion ROM at 00000000dfbc0000 [disabled] [size=256K]

00:13.0 PCI bridge: Texas Instruments PCI2250 PCI-to-PCI Bridge (rev 02)
(prog-i
f 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
	Latency: 128, Cache Line Size 08
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=128
	I/O behind bridge: 00bfe000-00bfefff
	Memory behind bridge: bfe00000-bfefffff
	Prefetchable memory behind bridge: bfd00000-bfdfffff
	Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot
-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:14.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
(rev 01)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
	Latency: 168, Cache Line Size 08
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at 00000000bfcff000 (32-bit, non-prefetchable)
[size=4K
]
	Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
	Memory window 0: bf8ff000-bfcfe000 (prefetchable)
	Memory window 1: 80000000-803ff000
	I/O window 0: 00000000-000001ff
	I/O window 1: 00000400-000005ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
	16-bit legacy interface ports at 0001

00:14.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller
(rev 01)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
	Latency: 168, Cache Line Size 08
	Interrupt: pin B routed to IRQ 0
	Region 0: Memory at 00000000bf8fe000 (32-bit, non-prefetchable)
[size=4K
]
	Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
	Memory window 0: bf4fe000-bf8fd000 (prefetchable)
	Memory window 1: 80400000-807ff000
	I/O window 0: 00000800-000009ff
	I/O window 1: 00000c00-00000dff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt-
PostWrite+
	16-bit legacy interface ports at 0001

00:14.2 System peripheral: Texas Instruments PCI1620 Firmware Loading
Function (
rev 01)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort
- <MAbort- >SERR- <PERR-
	Latency: 128 (1750ns min, 1000ns max), Cache Line Size 08
	Interrupt: pin ? routed to IRQ 19
	Region 0: I/O ports at bf5fc0 [size=64]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot
-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

~ #