Unable to map card memory, no io/mem-probe at all
Robert Schulze
rob at net-pr.de
Thu Mar 2 08:17:12 EST 2006
Hi,
I postet my problems with my Cardbus O2 OZ6812 some months ago, well I will
try it again now.
Always, when I insert a card (I tried my Cisco Aironet 350 and a Siemens
WLAN-Card)
the message "cs: unable to map card memory" occurs.
I also noticed, that no memory or io addresses get probed on
driver-startup - I don't know why.
Functionality of the devices is proved: when I boot e.g. a knoppix with old
pre-2.6.13 kernel and cardmgr, WLAN
ist working immediatly.
What the hell can I do to solve the problem?
with kind regards,
Robert Schulze
lsmod:
---
Module Size Used by
yenta_socket 24372 -
rsrc_nonstatic 11784 -
pcmcia 23984 -
pcmcia_core 35096 -
af_packet 16528 -
snd_es1938 18116 -
snd_pcm_oss 47776 -
snd_mixer_oss 16744 -
snd_pcm 80008 -
snd_page_alloc 8368 -
snd_opl3_lib 8744 -
snd_timer 20140 -
snd_hwdep 6720 -
snd_mpu401_uart 5736 -
snd_rawmidi 19456 -
snd_seq_device 6804 -
sis900 18504 -
mii 4328 -
uhci_hcd 30328 -
usbcore 108160 -
rtc 9472 -
---
lspci -vvv:
0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host
bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge
(rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f4000000-f7ffffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
0000:00:03.0 CardBus bridge: O2 Micro, Inc. OZ6812 Cardbus Controller (rev
05)
Subsystem: O2 Micro, Inc. OZ6812 Cardbus Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 14020000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10000000-11fff000 (prefetchable)
Memory window 1: 12000000-13fff000
I/O window 0: 00001c00-00001cff
I/O window 1: 00002000-000020ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+
PostWrite+
16-bit legacy interface ports at 0001
0000:00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900
PCI Fast Ethernet (rev 02)
Subsystem: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet
Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 173 (13000ns min, 2750ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1400 [size=256]
Region 1: Memory at f0000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 14000000 [disabled] [size=128K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:05.0 Modem: PCTel Inc HSP MicroModem 56 (rev 02) (prog-if 00
[Generic])
Subsystem: Uniwill Computer Corp: Unknown device 4000
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 1080 [size=64]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA
PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D3 PME-Enable- DSel=0 DScale=0 PME-
0000:00:06.0 Multimedia audio controller: ESS Technology ES1969 Solo-1
Audiodrive (rev 02)
Subsystem: ESS Technology: Unknown device 8898
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 10c0 [size=64]
Region 1: I/O ports at 1800 [size=16]
Region 2: I/O ports at 1830 [size=16]
Region 3: I/O ports at 1824 [size=4]
Region 4: I/O ports at 1820 [size=4]
Capabilities: [c0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 1810 [size=16]
0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 1060 [size=32]
0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
0000:01:00.0 VGA compatible controller: Silicon Motion, Inc. SM720 Lynx3DM
(rev b1) (prog-if 00 [VGA])
Subsystem: Silicon Motion, Inc. SM720 Lynx3DM
Control: I/O+ Mem+ BusMaster- SpecCycle+ MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 2.0
Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x2
Command: RQ=16 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW-
Rate=x2
---
dmesg:
Linux version 2.6.14 (root at mobil) (gcc-Version 3.3.5 (Debian 1:3.3.5-13)) #1
Mon Nov 7 21:20:30 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000eb400 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000bff0000 (usable)
BIOS-e820: 000000000bff0000 - 000000000bfff400 (ACPI data)
BIOS-e820: 000000000bfff400 - 000000000c000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
191MB LOWMEM available.
On node 0 totalpages: 49136
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 45040 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f6fd0
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @
0x0bffc63c
ACPI: FADT (v001 PTL BX-Arvrk 0x06040000 PTL 0x000f4240) @ 0x0bfff364
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x0bfff3d8
ACPI: DSDT (v001 UNIWIL 514I 0x06040000 MSFT 0x0100000b) @ 0x00000000
Allocating PCI resources starting at 10000000 (gap: 0c000000:f3f80000)
Built 1 zonelists
Kernel command line: root=/dev/hda3 ro vga=0x317
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 597.461 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 191892k/196544k available (1621k kernel code, 4144k reserved, 493k
data, 128k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1196.65 BogoMIPS
(lpj=2393307)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0e00)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd99e, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-103f claimed by PIIX4 ACPI
PCI quirk: region 1040-105f claimed by PIIX4 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *9 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 9) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs *10)
ACPI: PCI Interrupt Link [LNKD] (IRQs *11)
ACPI: Embedded Controller [EC0] (gpe 9)
ACPI: Power Resource [PFAN] (on)
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
PCI: Cannot allocate resource region 2 of device 0000:00:06.0
PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f4000000-f7ffffff
PREFETCH window: disabled.
PCI: Bus 2, cardbus bridge: 0000:00:03.0
IO window: 00001c00-00001cff
IO window: 00002000-000020ff
PREFETCH window: 10000000-11ffffff
MEM window: 12000000-13ffffff
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKB] -> GSI 9 (level, low) ->
IRQ 9
Simple Boot Flag at 0x36 set to 0x1
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
vesafb: framebuffer at 0xf4200000, mapped to 0xcc880000, using 3072k, total
8192k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at ca21:0001
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
mtrr: base(0xf4200000) is not aligned on a size(0x800000) boundary
mtrr: base(0xf4200000) is not aligned on a size(0x400000) boundary
vesafb: Mode is VGA compatible
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
ACPI: AC Adapter [AC] (off-line)
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SBTN]
ACPI: Fan [FAN] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (29 C)
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1818-0x181f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: FUJITSU MHM2060AT, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TORiSAN DVD-ROM DRD-U824, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 11733120 sectors (6007 MB) w/2048KiB Cache, CHS=12416/15/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 hda3
mice: PS/2 mouse device common for all mice
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12
08:13:09 2005 UTC).
ALSA device list:
No soundcards found.
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
Using IPI Shortcut mode
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 128k freed
Synaptics Touchpad, model: 1, fw: 4.1, id: 0x848a1, caps: 0x0/0x0
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
Adding 136544k swap on /dev/hda2. Priority:-1 extents:1 across:136544k
EXT3 FS on hda3, internal journal
Real Time Clock Driver v1.12
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) ->
IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x00001060
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: over-current change on port 2
sis900.c: v1.08.08 Jan. 22 2005
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKD] -> GSI 11 (level, low) ->
IRQ 11
0000:00:04.0: SiS 900 Internal MII PHY transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0x1400, IRQ 11, 00:a0:cc:c5:19:7f.
eth0: Media Link Off
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKC] -> GSI 10 (level, low) ->
IRQ 10
eth0: Media Link On 100mbps full-duplex
NET: Registered protocol family 17
eth0: Media Link On 100mbps full-duplex
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKB] -> GSI 9 (level, low) ->
IRQ 9
Yenta: CardBus bridge found at 0000:00:03.0 [1217:6872]
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: old bridge, disabling read prefetch/write burst
Yenta: ISA IRQ mask 0x0000, PCI irq 9
Socket status: 30000411
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!
cs: unable to map card memory!
---
More information about the linux-pcmcia
mailing list